• Current Optics and Photonics
• /
• v.2 no.1
• /
• pp.27-33
• /
• 2018

We report the physical implementation of a tunable photonic microwave delay line filter based on injection locking of a single Fabry-Perot laser diode (FP-LD) to a reflective semiconductor optical amplifier (RSOA). The laser generates equally spaced multiple wavelengths and a single tapped-delay line can be obtained with a dispersive single mode fiber. The filter frequency response depends on the wavelength spacing and can be tuned by the temperature of the FP-LD varying lasing wavelength. For amplitude control of the wavelengths, we use gain saturation of the RSOA and the offset between the peak wavelengths of the FP-LD and the RSOA to decrease the amplitude difference in the wavelengths. From the temperature change of total $15^{\circ}C$, the filter, consisting of four flat wavelengths and two wavelengths with slightly lower amplitudes on both sides, has shown tunability of about 390 MHz.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.11 no.1
• /
• pp.171-182
• /
• 2015

The general wavelet transform has profitable property in non-stationary signal analysis specially. The tunable Q-factor wavelet transform is a fully-discrete wavelet transform for which the Q-factor Q and the asymptotic redundancy r, of the transform are easily and independently specified. In particular, the specified parameters Q and r can be real-valued. Therefore, by tuning Q, the oscillatory behavior of the wavelet can be chosen to match the oscillatory behavior of the signal of interest, so as to enhance the sparsity of a sparse signal representation. The TQWT is well suited to fast algorithms for sparsity-based inverse problems because it is a Parseval frame, easily invertible, and can be efficiently implemented. The transform is based on a real valued scaling factor and is implemented using a perfect reconstruction over-sampled filter bank with real-valued sampling factors. The transform is parameterized by its Q-factor and its over-sampling rate, with modest over-sampling rates being sufficient for the analysis/synthesis functions to be well localized. This paper describes filter design of 2D discrete-time wavelet transform for which the Q-factor is easily specified. With the advantage of this transform, perfect reconstruction filter design and implementation for performance improvement are focused in this paper. Hence, the 2D transform can be tuned according to the oscillatory behavior of the image signal to which it is applied. Therefore, application for performance improvement in multimedia communication field was evaluated.

• Journal of information and communication convergence engineering
• /
• v.8 no.3
• /
• pp.263-266
• /
• 2010

In this paper, a novel defected ground structure (DGS) pattern with enhanced effective capacitance (varactor diode) and a hole in PCB center is presented. The increase in effective capacitance enables the new DGS pattern to achieve a lower resonance than the DGS pattern for the same etched square dimension. The hole in the center also can make resonator frequency lower with better characteristic. According to the tunable characteristic of varactor diode, the resonant frequencies can be tunable. Simulation results show that a lower resonance is achieved with active device, compared to a common DGS pattern.

• Current Optics and Photonics
• /
• v.6 no.6
• /
• pp.634-641
• /
• 2022

A frequency stable and tunable optoelectronic oscillator (OEO) incorporating an optical phase shifter and a phase-shifted fiber Bragg grating (PS-FBG) is designed and analyzed. The frequency tunability of the OEO can be realized by using a tunable microwave photonic bandpass filter consisting of a PS-FBG, a phase modulator. The optical phase compensation loop is used to compensate for the phase variations of the RF signal from the OEO by adjusting an optical phase shifter. Simulation results demonstrate that the output RF signals of the OEO can be tuned in a frequency range of 118 MHz to 24.092 GHz. When the ambient temperature fluctuates within ±3.9 ℃, the frequency drifts of the output RF signals are less than 68 Hz, the side-mode suppression ratios are more than 69.39 dB, and the phase noise is less than -92.49 dBc/Hz at a 10 kHz offset frequency.

• Proceedings of the Optical Society of Korea Conference
• /
• 1998.08a
• /
• pp.168-169
• /
• 1998

• Proceedings of the Optical Society of Korea Conference
• /
• 1998.08a
• /
• pp.166-167
• /
• 1998

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.344-344
• /
• 2001

• Proceedings of the Optical Society of Korea Conference
• /
• 1999.08a
• /
• pp.90-91
• /
• 1999

• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.99-103
• /
• 2006

A tunable wavelength filter was proposed and demonstrated by using the UV nanoimprint technique. It consists of a Bragg grating in polymer waveguides and a heating electrode. The manufacturing of the grating was substantially simplified with the introduction of a smart imprint stamp containing a waveguide pattern integrated with the grating pattern. The center wavelength of the filter was successfully tuned by taking advantage of the thermooptic effect in polymers, which was induced by supplying electrical power to the electrode. For the fabricated device, a transmission dip of ${\~}$15 dB and a 3-dB bandwidth of 0.8 nm were obtained at the Bragg wavelength of ${\~}$l560 nm. The achieved thermooptic tuning efficiency was ${\~}$0.28 nm/mW, while the center wavelength was shifted from 1560 nm to 1558 nm with the electrical power consumption of 7 mW.

• Korean Journal of Optics and Photonics
• /
• v.19 no.1
• /
• pp.36-42
• /
• 2008

Implementation of a wavelength-swept source with constant tuning rate adopting a PZT-type tunable filter, requires the knowledge of hysteresis of the filter used. The hysteresis must be considered to avoid any degradation in resolution of the optical frequency domain reflectometry (OFDR) system. An optical spectrum analyzer (OSA) could be used to do the hysteresis measurement, but its measurement time is too long for the high-speed driving conditions for the filter. We proposed a new hysteresis measurement method based on OFDR, which could measure the hysteresis in a real driving condition. A hysteresis measurement apparatus consisted of wavelength-swept source, interferometer, signal processing unit, and PC program is built and used to do the measurement. It is concluded that the new method is useful in the measurement of hysteresis at real driving conditions by successfully implementing a swept-wavelength source whose wavelength change is linear in time.