• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 제5회 박판성형 SYMPOSIUM
• /
• pp.45-48
• /
• 2006

Recently, the use of tubular hydroforming technology has seen increased usage and increased consideration for wide range of tubular automotive applications. In manufacturing hydroformed parts, bending and pre-forming operations are often required prior to the hydroforming process. Higher bending quality of bent tubes is crucial for the successful hydroforming operation because most of plastic strains and wall thinning at the extrados of bend area occur in the bending operation. Springback is also observed due to elastic recovery of tube material after bending. Proper correction of springback is required not only to well place the bent tube into a hydroforming die cavity but also to avoid pinching when the upper die is brought down to closing position. Therefore, prediction of springback at early development stage is one of the key factors to produce high quality hydroformed parts. In this study, a variety of bending experiments has been carried out to investigate springback amount under change in bending angle and material boosting. Throughout the experimental approach, springback characteristics of bent tubes are quantified according to the change in various bending parameters, and a mathematical model to predict correction amount of springback to a given bend angle is found.

• 한국산학기술학회논문지
• /
• 제12권1호
• /
• pp.7-14
• /
• 2011

연질 동관은 조선, 자동차, 플랜드, 냉동공조 기기 등에 많이 사용되는 대표적인 파이프 재료 중의 하나이다. 그러나 이러한 재료들은 벤딩가공시 외부의 주름, 스프링백, 관이 얇아지는 현상들이 자주 발생하여 문제가 된다. 본 논문에서는 연성재질을 벤딩시 맨드럴이 슬라이딩 가이드 레일을 따라서 파이프를 누르는 벤딩방식을 선택한 연성재질 전용 벤딩머시인을 제작하여 이와 같은 현상을 줄였다. 이의 성능을 확인하는 과정에서 재료로 사용한 동관의 직경이 작을수록 스프링백 현상은 증가하였고 또한 굽힘각도가 클수록 컸다. 또한 동관의 벤딩시 주름이 거의 발생하지 않는 성형품을 제작할 수 있었다.

• Structural Engineering and Mechanics
• /
• 제9권4호
• /
• pp.339-347
• /
• 2000

The creep deformation of pure bending (hold constant moment for a period of time) tests were conducted in this paper. Thin-walled tubes of 304 stainless steel were used in this investigation. The curvature-ovalization measurement apparatus, designed by Pan et al. (1998), was used for conducting the present experiments. It has been found that as soon as the creep deformation is started, the magnitudes of the tube curvature and ovalization of tube cross-section quickly increase. The magnitudes of the creep curvature and ovalization of tube cross-section increase fast with a higher hold moment than that with a lower one. Owing to the continuously increasing curvature during the creep deformation, the tube specimen buckles eventually.

• Composites Research
• /
• 제20권3호
• /
• pp.8-16
• /
• 2007

자동차 충돌이나 전복사고에 있어서 부재들의 변형은 축방향 압축붕괴와 함께 굽힘붕괴가 혼합된 변형양상을 보여주고 있으며, 자동차에 사용되는 대부분의 박벽관 부재는 굽힘붕괴가 주된 붕괴형태로 나타나고 있다. 하지만 혼성 사각관의 굽힘붕괴에 대한 연구는 축방향 붕괴의 연구에 비해 많이 부족한 현실이다. 본 논문에서는 알루미늄-복합재료 혼성 사각관의 굽힘 붕괴 거동 및 에너지 흡수 특성을 실험적 방법으로 연구하여 경량화 구조부재로서의 적용가능성을 조사하였다. 접착필름 살입형 경화법으로 제작된 알루미늄-복합재료 혼성 사각관 보에 대해 복합 재료 층의 적층두께와 적층 각에 따른 굽힘 성능을 평가하였다. 본 혼성 사각관 보는 복합재료만으로 구성된 사각관 보에서 발생할 수 있는 불안정한 붕괴모드를 안정적인 붕괴로 전환시키면서, 단순 알루미늄 사각관에 비해 에너지 흡수 능력이 향상되었고, 특히 $[0^{\circ}/90^{\circ}]s$를 적층한 혼성 사각관의 경우 벽두께 1mm인 알루미늄 사각관 시험편과 비교하여 흡수에너지가 1.78배 증가하였고 단위무게당 흡수에너지는 1.29배로 증가함을 보였다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.261-266
• /
• 1998

In this study, crush characteristics of thin-walled rectangular tube is investigated. The stiffness of the element is obtained from analytical moment-rotation relationship and approximated load-deflection relationship of thin-walled rectangular tube. A computer program is developed for the large deformation analysis of frame. An incremental displacement method is used in the program and at each incremental stage, the stiffness matrix of the total structure is checked with the state each element for bending and compression.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 봄 학술발표회 논문집
• /
• pp.317-322
• /
• 2001

A mathematical modelling technique is proposed for estimating the additional bending stresses of tube(s)-in-tube structures due to tube-tube interaction, which has a significant effects on the shear-lag phenomenon. The proposed method simulates the framed-tube structures with multiple internal tubes as equivalent multiple tubes, each composed of four equivalent orthotropic plate panels. Hence, the tube(s)-in-tube structure can be analysed by using an analogy approach where each tube is individually modelled by a continuous beam that can account for the flexural and shear deformations as well as the shear-lag effects. The numerical analysis is applicable for the structural analysis of framed-tube structures with single and multiple internal tubes, as well as those without internal tubes. The shear-lag phenomenon of such structures is studied with additiona] bending stresses and shear-lag reversal points.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제11권3호
• /
• pp.105-113
• /
• 2003

This study developed a practical two-microphone impedance tube method to measure the sound transmission loss of sound isolation materials without the use of an expensive reverberation room or an acoustic intensity probe. In order to evaluate the validation and applicability of the two-microphone impedance tube method, sound transmission losses for several sound isolation materials with different surface density and bending stiffness were measured, and the measured values were compared with the results from the reverberation room method and the theory. From the experimental results, it was found that the accuracy of sound transmission loss obtained by the impedance tube method depends upon the diameter size of the impedance tube (i.e., tested sample size). For sound isolation materials having relatively large bending stiffness such as acryl, wood, and aluminum plates, it was found that the impedance tube method proposed by this study was not valid to measure the sound transmission loss. On the other hand, for sound isolation materials having relatively small bending stiffness such as rubber, polyvinyl, and asphalt sheets, the comparisons of transmission loss between the results from the impedance tube method and the theory showed a good agreement within the range of the frequencies satisfying the normal incidence mass law. Therefore, the two-microphone impedance tube method proposed by this study can be an effective measurement method to evaluate the sound transmission loss for soft sound isolation sheets having relatively small bending stiffness.

• 소성∙가공
• /
• 제18권4호
• /
• pp.336-341
• /
• 2009

Hydroformed parts have higher dimensional accuracy, structural strength, and dimensional repeatability. Particularly in the automotive industry, manufacturing of parts with complex shapes from tubular materials sometimes requires one or more pre-forming operations such as bending before the hydroforming process. The pre-bending process is an important process for the successful hydroforming in the case where the perimeter of the blank is nearly the same as that of final product. The bendability of a tube depends on the parameters such as the bending radius, welding methods, mechanical properties and hardness. Through the stainless steel tubes bent by rotary draw bending machine, this study shows the following : (1) The influence on spring back ratio variation with stress level in the welded bent tube. (2) The Cross-section ovality variation with weld seam position and bending radius. (3) The relation between elongation and thickness reduction of tension zone with weld seam position and bending radius. (4) Workability evaluation of bent stainless steel tubes through the hardness of materials and hardness increment. The results of this study may help to understanding of characteristics on bendability of stainless steel tubes.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1852-1857
• /
• 2003

This study is concerned about the development of three-dimensional bending machine for heat exchanger. Recently, three-dimensional bending is required for various heat exchanger. The purpose of this study is design of three-dimensional bending machine by analysis of bending process and structural analysis simulation. The analysis is carried out by FEM simulation using DEFORM and CATIA V5 software. The copper-tube is modeled by shell elements and the machine is modeled by placing proper shell and solid finite elements and fictitious mass properties to represent the real one. The final results of analysis are applied to the design of three-dimensional bending machine and the machine is successfully developed.

• 소성∙가공
• /
• 제32권4호
• /
• pp.221-227
• /
• 2023

While tube bending is a conventional forming technique, it is still used to make curved products for load-bearing members or aesthetically pleasing parts in various manufacturing industries such as automotive, aerospace, and others. Whole or local deformation of the final product such as springback, distortion, or local buckling are of interest in metal forming or precision manufacturing. In this paper, the factors affecting the cross-sectional deformation are explored. A 5-axis stretch bending machine was used for two-dimensional bending with extruded AA6082-T4 rectangular tubes. Three different bending sequences were employed: stretch before bending, stretch after bending, simultaneous bending and stretch. Furthermore, by considering both the stretch and bending angle, cross-sectional deformation was also analyzed. It was observed that employing stretch bending techniques can effectively reduce cross-sectional deformation and contribute to overall quality enhancement. Through this study, it was revealed that these factors have an impact on the cross-sectional deformation of the tubes.