• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.137-138
• /
• 2002

The benefits of using DLC coatings on steel in dry sliding are well known. The present study has investigated the effects of using the same materials but in a boundary lubricated environment. Tribological tests were performed using a load-scanning device and a lubricant with an extreme-pressure (EP) additive. XPS and grazing incidence XRD are used for chemical analysis. The chemical composition of the resulting tribofilm is correlated to different friction behaviors and contact loads, and indicates that high loads are beneficial for formation of low friction tribofilm.

• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.302-307
• /
• 2008

The running-in behaviour of the metal carbon coating (WC/C) was evaluated with regard to its applicability as wear-resistant coating for key components in engines. Reciprocating wear tests under lubricated condition employing an oscillating friction wear tester were performed to investigate the tribological behaviors of the coatings in ambient environment. Confocal microscopy and scanning electron microscopy were used to observe worn surfaces and the wear scars on the steel balls. Elemental composition of the coating and worn surfaces were characterized using Auger electron spectroscopy. The friction behavior of WC/C coating was comparable to common carbon-based coatings. Thin tribofilm was formed on the worn surface of the steel ball due to material transfer and tribochemical reaction whereas there was no evidence of tribofilm generation on the coating surface. indicating the chemical innertness of WC/C coating.

• Tribology and Lubricants
• /
• 제18권2호
• /
• pp.138-143
• /
• 2002

Abstract - Tribofilms formed on won surface protect the DLC coating surface and decrease the fiction coefficient. However it is very difficult to evaluate their micromechanical properties due to their small thickness, inhomogeneity and discontinuity. The phase contrast images in tapping mode atomic farce microscopy allow an estimation of inhomogeneity in micromechanical properties of the sample surface. The purpose of this investigation is to demonstrate how the phase contrast images contribute to the characterization of thin tribofilms.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.299-304
• /
• 2001

Tribofilms formed on worn surface protect the DLC coating surface and decrease the friction coefficient. However it is very difficult to evaluate their micromechanical properties due to their small thickness, inhomogeneity and discontinuity. The phase contrast images in tapping mode atomic force microscopy allow an estimation of inhomogeneity in micromechanical properties of the sample surface. The purpose of this investigation is to demonstrate how the phase contrast images contribute to the characterization of thin tribofilms.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.975-985
• /
• 2011

Cu-Matrix sintered brake pads and low alloyed heat resistance steel are most applied to basic brake system for high energy moving machine. In this research, we analyzed tribological characteristics for influence of air velocity between disk and pad. At low brake pressure with air flow, friction stability was decreased due to no formation of tribofilm at disk surface. But there are no significant change of friction coefficient at all test conditions. Wear rate of friction materials were decreased with increasing of air flow velocity. In result, air flow velocity influenced friction stability, wear rate of friction materials and disk but not friction coefficient.

• Tribology and Lubricants
• /
• 제29권1호
• /
• pp.19-26
• /
• 2013

Cu-matrix sintered brake pads and low-alloy heat-resistant steel are commonly applied to basic brake systems in high-energy moving machines. In this research, we analyzed the tribological characteristics to determine the influence of the air velocity between the disk and pad. At a low brake pressure with airflow, the friction stability was decreased as a result of the lack of tribofilm formation at the disk surface. However, there were no significant changes in the friction coefficient under any of the test conditions. The wear rates of the friction materials were decreased with an increase in the airflow velocity. As a result, the airflow velocity influenced the friction stability, as well as the wear rate of the friction materials and disk, but not the friction coefficient.

• Tribology and Lubricants
• /
• 제30권4호
• /
• pp.240-245
• /
• 2014

Low alloy heat resistant brake disk and sintered brake pad are applied to mechanical brake system for the speed-up of urban rapid transit. In this research, we analyzed how the frictional characteristics between brake disk and pad are influenced by the disk mass. At a high disk mass, the friction stability was the lower value as a result of the lack of tribofilm formation at the disk surface. Wear rates of friction materials showed the higher value at a low disk mass and wear rates of 10 mm and 15 mm showed the similar level. Average friction coefficient was the lower value at the 10 mm disk thickness and range of variation of average friction coefficient was also the smaller value at the 10 mm disk thickness. However, there were no significant changes in the friction coefficients under any of test conditions. Surface roughness of a disk showed the highest value at the 5 mm disk and surface roughnesses of 10 mm and 15 mm showed the similar level. As a result, friction characteristics of disk mass influenced the friction stability, as well as the wear rate of friction pad and disk, but not the friction coefficient.

• Nano
• /
• 제13권12호
• /
• pp.1850144.1-1850144.13
• /
• 2018

A nano-$MoS_2$/montmorillonite K-10 (K10) composite was prepared and characterized. The composite contains two types of 2H-$MoS_2$ nanoparticles. One is the hollow spherical $MoS_2$ with a size range of 75 nm, and the other is the spherical nano cluster of $MoS_2$ with a size range of 30 nm. The two kinds of nano-$MoS_2$ were formed via assembly of numerous $MoS_2$ nano-platelets with a size of ~10 nm. A tribological comparison was then made among nano-$MoS_2$/K10, K10, nano-$MoS_2$ and a mechanical mixture of K10 and nano-$MoS_2$. K10 reduced the wear but slightly increased the friction. Nano-$MoS_2$ remarkably reduced both friction and wear. The mechanical mixture demonstrated better wear resistance than nano-$MoS_2$, indicating a synergistic anti-wear effect of nano-$MoS_2$ and K10. The synergistic effect was reinforced using nano-$MoS_2$/K10 instead of the mechanical mixture. A part of the $MoS_2$ in the contact region always lubricated the friction pair, and the rest formed a tribofilm. K10 segregated the friction pair to alleviate the ablation wear but magnified the abrasive wear. S-$MoS_2$ protects K10 and they together function as both a lubricant and an isolating agent to reduce the ablation and abrasive wear.

• 공업화학
• /
• 제27권6호
• /
• pp.583-589
• /
• 2016

Zinc dialkyldithiophosphate (ZDDP)와 같이 금속을 포함한 윤활유 첨가제는 값이 싸다는 이점 때문에 널리 사용되고 있으나, 재와 같은 불순물이 발생한다는 단점이 있다. 본 연구에서는 ZDDP를 부분적으로 대체하여 zinc와 같은 금속을 포함하지 않는 구조인 알칸디올로부터 유래하는 bis[3-(dialkyloxyphosphorothionyl) thio-2-methylpropanyloxy] butane(BAP4)을 간편하고 효율적으로 합성하였고, 합성한 BAP4 화합물들에 따른 내 마모 특성을 살펴보았다. 여러 가지 알킬기가 있는 BAP4 화합물들이 4-ball 시험법에 의해 마모 직경(Wear scar diameter, WSD) 값이 측정되었다. BAP4 화합물에서 알킬기가 4에서 8로 증가함에 따라 WSD 값은 0.59 mm에서 0.45 mm로 급격히 감소했으나, BAP4의 알킬기가 8에서 14로 증가할 경우 WSD 값은 0.45 mm에서 0.50 mm로 서서히 증가했다. 따라서 BAP4 화합물 중 가장 WSD 값이 적게 나타난 것은 B8P4이었다. 윤활기유에 B8P4와 ZDDP를 0.50 wt%로 첨가하여 4-ball 시험을 실시한 결과, B8P4와 ZDDP의 WSD 값은 각각 0.45, 0.54 mm로 측정되었다. 또한, 열 중량 분석기(Thermogravimetric Analyzer, TGA)를 통해 열안정성을 확인하였고, 에너지 분산형 X-선 분광분석기(Energy-Dispersive X-rays Spectroscopy, EDS)로 tribofilm이 제대로 형성되었는지를 측정하였다.

• 공업화학
• /
• 제29권4호
• /
• pp.405-412
• /
• 2018

알칸디올로부터 유래된 주사슬의 탄소수가 6, 9, 11인 bis[3-(dialkyloxylphosphorothionyl)thio-2-methylpropanyloxy]alkane (BAPA)를 합성하였으며, 이를 zinc dialkyl dithiophosphates (ZDDP)와 비교하여 마모억제성능을 살펴보았다. 탄소 주사슬의 길이에 따른 BAPA의 내마모성능을 확인하기 위하여 4-ball 시험을 하였다. 기유무게의 1% 농도로 첨가제를 넣고 WSD (wear scar diameter)를 측정하였고, 각 0.472, 0.459, 0.480 mm로 나타났다. 또한 BAPA 화합물 중 bis[methacryloyloxy]nonane (BMOO9)의 곁사슬인 dialkyl dithiophosphoric acid (DDP)의 탄소수를 4, 8, 12로 변화시켜 합성하여, 4-ball 시험을 하였다. 그 결과로 WSD의 값은 각각 0.537, 0.459, 0.531 mm로 측정되었다. 곁사슬이 짧으면 필름이 얇게 형성되고, 길면 필름형성을 방해하여 탄소수가 8개일 때의 값이 제일 좋게 나타났다. ZDDP의 경우 동일한 조건에서 WSD의 값이 0.563 mm로 측정되었고, 합성한 BAPA의 화합물이 마모억제용 첨가제로 더 우수한 성능을 갖는다는 것을 확인하였다.