• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.1B
• /
• pp.73-81
• /
• 2009

This paper presents a numerical investigation of the impact of the secondary currents on solute transport in open-channel flows. The RANS model with Reynolds stress model is used for flow modeling, and the GGDH(generalized gradient diffusion hypothesis) model is used to close the scalar transport equation. Using the developed model, the impact of secondary currents on solute transport in open channel flows over smooth-rough strip is investigated. Through numerical experiments, the secondary currents are found to affect the solute spreading, leading a movement of the position of the peak concentration and a skewed distribution of solute concentration. Due to the lateral flow of secondary currents near the free surface, the concentration at the rough strip is found to be larger than that at the smooth strip bed. The solute at the rough strip is more rapidly transported than smooth bed. A magnitude analysis of the solute transport rate in scalar transport equation is also carried out to investigate the effect of secondary currents and scalar flux on the concentration distribution.

• Particle and aerosol research
• /
• v.5 no.3
• /
• pp.123-131
• /
• 2009

This paper presents simulation results of particle transport in low-pressure, low-temperature plasma environment. The size dependent transport of particles in the plasma is investigated with a two-dimensional simulation tool developed in-house for plasma chamber analysis and design. The plasma model consists of the first two and three moments of the Boltzmann equation for ion and electron fluids respectively, coupled to Poisson's equation for the self-consistent electric field. The particle transport model takes into account all important factors, such as gravitational, electrostatic, ion drag, neutral drag and Brownian forces, affecting the motion of particles in the plasma environment. The particle transport model coupled with both neutral fluid and plasma models is simulated through a Lagrangian approach tracking the individual trajectory of each particle by taking a force balance on the particle. The size dependant trap locations of particles ranging from a few nm to a few ${\mu}m$ are identified in both electropositive and electronegative plasmas. The simulation results show that particles are trapped at locations where the forces acting on them balance. While fine particles tend to be trapped in the bulk, large particles accumulate near bottom sheath boundaries and around material interfaces, such as wafer and electrode edges where a sudden change in electric field occurs. Overall, small particles form a "dome" shape around the center of the plasma reactor and are also trapped in a "ring" near the radial sheath boundaries, while larger particles accumulate only in the "ring". These simulation results are qualitatively in good agreement with experimental observation.

• Nuclear Engineering and Technology
• /
• v.55 no.11
• /
• pp.4125-4133
• /
• 2023

The transportation of spent nuclear fuel is an important process that involves road and sea transport from an interim storage facility to storage and final disposal sites. As spent nuclear fuel poses a significant risk, carefully evaluating its vibration and shock characteristics under normal transport conditions is essential. In this regard, full-scale multi-modal transport tests (MMTT) have been conducted domestically and internationally. In this paper, we discuss the process of developing a multi-body dynamics (MBD) model to analytically simulate conditions that cannot be considered in tests. The MBD model is based on the KORAD-21 transportation system was validated using the Korean MMTT results from 2020 to 2021. This paper summarizes the details of the development and verification of the MBD model for the KORAD-21 transportation system under normal transport test conditions. This approach can be applicable to various transportation scenarios and systems, and the results of this study will help to ensure that nuclear fuel transportation is conducted safely and effectively.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.443-449
• /
• 2004

In this paper, we established a simulation model for transport vehicle that carries the container transportation between apron and yard block on automated container terminal with a perpendicular yard layout. Usually, the efficiency of container terminal is evaluated by productivity of container cranes at apron, and though there are enough support of transport vehicles and yard cranes, can improve the productivity of container cranes. Especially, transport vehicle is very important factor in productivity of container cranes and has variable work productivity according to loading and unloading situation of container cranes. Therefore, a method that can estimate work productivity of transport vehicle efficiently is required. We analyzed work productivity of transport vehicle using simulation model that has state transition of transport vehicle. We performed various simulation experiment and analyzed work productivity of transport vehicle and calculated the required number of transport vehicle by container crane additionally.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.421-426
• /
• 2004

Increasing of the multinational corporation brought into the international multimodal Increasing of the multinational corporation brought into the international multimodal transport on the logistics environment. In case of Europe which have a great infrastructure, they are tried to develope a second of the silk road constantly. This paper emphasized the importance of international multimodal transport and proposed the model for northeast multimodal transport. For this research, we analyzed the multimodal transport system in Europe and north corridor of TAR. We are expecting economic effect of the route is including republic of korea and developed a model for connecting with sea, air and road. Actually, this research can not be enough data of numerical value for proving this effectiveness. but we developed and proposed a specific route of multimodal transport that was never suggested. Consequently, we established basic ground for comparing each transport route in the future research.

• Journal of Korea Water Resources Association
• /
• v.37 no.12
• /
• pp.1033-1041
• /
• 2004

A 2-dimensional numerical sediment transport model using erosion rates in undisturbed conditions has been developed and applied to calculating the suspended sediment concentrations and bed level changes in the Lower Fox River The model reduces inaccuracy of sediment model by using the accurate erosion rates obtained in a flume (called Sedflume). The flume has been developed to measure erosion rates as a function of sediment depth and at the situation of high shear stresses such as flood event. Both mechanisms of suspended load and bedload transport are included in the model. The model results were verified for the description of sediment transport in a straight channel and the sediment transport during flood event in the Lower Fox River The results of Lower Fox River simulation showed good agreements with the observed SS concentrations. This model can be used to simulate sediment transport under the high shear conditions such as flood.

• Journal of computational fluids engineering
• /
• v.18 no.4
• /
• pp.53-60
• /
• 2013

The boron transport model has been implemented into the CUPID code to simulate the boron transport phenomena of the PWR. The boron concentration conservation was confirmed through a simulation of a conceptual boron transport problem in which water with a constant inlet boron concentration injected into an inlet of the 2-dimensional vertical flow tube. The step wise boron transport problem showed that the numerical diffusion of the boron concentration can be reduced by the second order convection scheme. In order to assess the adaptability of the developed boron transport model to the realistic situation, the ROCOM test was simulated by using the CUPID implemented with the boron transportation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.6
• /
• pp.600-606
• /
• 2009

In this paper, the coupled model with hydrogen transport and elasto-plasticity behavior is introduced. This model is implemented to the general-purpose FE code, ABAQUS, via the user-defined subroutine UMAT and UMATHT. In UMAT, the spatial gradients of hydrostatic stress and hydrogen induced deformation are calculated, and then are passed into UMATHT. Heat transfer equation within UMATHT is substituted by hydrogen transport equation including the effects of stress states and strain hardening. To validate this model, the finite element analyses coupled with hydrogen transport and mechanical loading are performed for the boundary layer specimens with low and high strength steel properties. The FE results are compared with the previous studies by Taha and Sofronis (2001).

• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.3
• /
• pp.271-285
• /
• 2006

A two-dimensional photochemical transport model (2D PTM) is simulated to describe the transport and chemical reaction of ozone related to aerosols in the troposphere and stratosphere. The vertical profiles and total amounts of ozone, which are advected by both residual Eulerian circulation and the adiabatic circulation under certain circumstance, have been compared with the observation data such as ozonesondes, Brewer spectrometer, the Upper Atmosphere Research Satellite (UARS), and the Total Ozone Mapping Spectrophotometer (TOMS). As a result, we find that the observed distribution of ozone Is adequately reproduced in the model at middle and high latitude in the Northern Hemisphere as well as at Phang ($36^{\circ}\;02'N,\;129^{\circ}\;23'E$) in South Korea. In particular, the 2D PTM is well simulated in the ozone decrease due to the Pinatubo volcanic eruption in 1991. However, ozone mixing ratio are more underestimated than those of UARS and ozonesondes, because are very sensitive to the latitude of transport across the tropopause associated with both Rummukainen errors and off-line model. Relative mean bias errors and relative root mean square errors of ozone calculations using the 2D PTM are shown within${\pm}10%$, respectively.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.917-920
• /
• 1995

A mathematical model describing the relationship between longitudinal tension and tangential velocity of web/roller in a multi-span web transport system has been developed. An experiment was carried out for typical conditions to validate the mathematical model for tension behavior in a multispan system. A two-span prototype prototype web transport system with winder and unwinder was manufactured for the experiment. By comparing simulation and experimental results, the mathematical model for tension and velocity in a multi-span web transport system is confirmed to be valid for typical conditions. Tension transfer phenomenon was also confirmed though the simulation as well as experimentation.