• Journal of Power Electronics
• /
• v.12 no.4
• /
• pp.519-527
• /
• 2012

A high step-down multiple-output LED driver is proposed in this paper. Firstly, the derivation of the driver with dual-output is presented and its operation principle and steady state performance are analyzed in detail. Secondly, a high step-down N-channel LED driver is proposed and its current auto-balance characteristic and step-down ratio are analyzed. Finally, an experimental prototype is built and the experimental results are given. The theoretical analysis and experimental results show that the proposed driver has the following virtues: First, if load balancing is achieved, the voltage gain is 1/N that of a Buck driver, where N is the number of channels. Second, each output automatically has an equal output current, without requiring more current close-loop control circuits than a Buck driver. Last, the voltage stresses of the switches and diodes are lower than those of a Buck driver, meaning that lower voltage switches and diodes can be used, and a higher efficiency can be expected.

• Proceedings of the KIEE Conference
• /
• 2003.07e
• /
• pp.62-69
• /
• 2003

In recent years, data transmission using power lines has been much highlighted. Power line is known to be cost-effective communication medium because the entire cable infrastructure has been already established and it is entirely connected with any home. Recently, the target of researches is to communicate data reliably over power lines at the speed of at least 1Mbits/s over the frequency range from 1MHz to 10MHz. OFDM communication system has been used for the high speed data transmission. Next, the conventional and adaptive OFDM systems for high speed data transmission over power line channel are investigated. The performance of AOFDM(adaptive OFDM) over the frequency selective channel with impulsive and narrow-band noise are studied to be a nice solution for high speed data transmission over power lines. The simulation results show that data the rates of the AOFDM are improved about 47% more than the ones of the conventional OFDM over the frequency response of case 4. In the results, the data rate has been much improved by the proposed adaptive algorithm in the frequency selective channel.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.1
• /
• pp.318-330
• /
• 2015

In wearable sensor systems (WSSs), sensor nodes are deployed around human body parts such as the arms, the legs, the stomach, and the back. These sensors have limited lifetimes because they are battery-operated. Thus, transmission power control (TPC) is needed to save the energy of sensor nodes. The TPC should control the transmission power level (TPL) of sensor nodes based on current channel conditions. However, previous TPC algorithms did not precisely estimate the channel conditions. Therefore, we propose a new TPC algorithm that uses an accelerometer to directly measure the current channel condition. Based on the directly measured channel condition, the proposed algorithm adaptively adjusts the transmission interval of control packets for updating TPL. The proposed algorithm is efficient because the power consumption of the accelerometer is much lower than that of control packet transmissions. To evaluate the effectiveness of our approach, we implemented the proposed algorithm in real sensor devices and compared its performance against diverse TPC algorithms. Through the experimental results, we proved that the proposed TPC algorithm outperformed other TPC algorithms in all channel environments.

• Journal of Power Electronics
• /
• v.12 no.3
• /
• pp.410-417
• /
• 2012

In this paper, a direct current control method based on a one-cycle controller (DCOCC) for double frequency buck converters (DF buck) is proposed. This control method can make the average current through the high frequency and low frequency inductors of a DF buck converter equal. This is similar to the average current control method. However, the design of the loop compensator is much easier when compared with the average current control. Since the average current though the high frequency and low frequency inductors is equivalent, the current stress of the high frequency switches and the switch losses are minimized. Therefore, the efficiency of the DF buck converter is improved. Firstly, the operation principle of DCOCC is described, then the small signal models of a one cycle controller and a DF buck converter are presented based on the state space average method. Eventually, a system block diagram of the DCOCC controlled DF buck is established and the compensator is designed. Finally, simulation and experiment results are given to verify the correction of the theory analysis.

• Journal of Power Electronics
• /
• v.15 no.1
• /
• pp.86-95
• /
• 2015

An active clamp high step-up boost converter with a coupled inductor is proposed in this paper. In the proposed strategy, a coupled inductor is adopted to achieve a high voltage gain. The clamp circuit is included to achieve the zero-voltage-switching (ZVS) condition for both the main and clamp switches. A rectifier composed of a capacitor and a diode is added to reduce the voltage stress of the output rectifier diode. As a result, diodes with a low reverse-recovery time and forward voltage-drop can be utilized. Since the voltage stresses of the main and clamp switches are far below the output voltage, low-voltage-rated MOSFETs can be adopted to reduce conduction losses. Moreover, the reverse-recovery losses of the diodes are reduced due to the inherent leakage inductance of the coupled inductor. Therefore, high efficiency can be expected. Firstly, the derivation of the proposed converter is given and the operation analysis is described. Then, a steady-state performance analysis of the proposed converter is analyzed in detail. Finally, a 250 W prototype is built to verify the analysis. The measured maximum efficiency of the prototype is 95%.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.3
• /
• pp.970-977
• /
• 2014

In this paper, the artificial neural network is used to predict the junction temperature of the IGBT power module, by measuring the temperature sensitive electrical parameters (TSEP) of the module. An experiment circuit is built to measure saturation voltage drop and collector current under different temperature. In order to solve the nonlinear problem of TSEP approach as a junction temperature evaluation method, a Back Propagation (BP) neural network prediction model is established by using the Matlab. With the advantages of non-contact, high sensitivity, and without package open, the proposed method is also potentially promising for on-line junction temperature measurement. The Matlab simulation results show that BP neural network gives a more accuracy results, compared with the method of polynomial fitting.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.488-490
• /
• 2004

The technical data for transmission line design and maintenance are calculated by a very complicated numerical formula so it is almost impossible to solve them by hand. Therefore the TOWER+ EXPERT SYSTEM was developed to systematically support technical data for transmission line design and maintenance. This system is able to calculate technical data which is applied to all conductors in our county, - that is 12 kinds of systems with 86 numbers of standard conductors, - and is programed to be user friendly by adopting dialogue windows, menu selection functions. Moreover, it minimizes input data by automatically providing standard transmission line design data, and it includes guidance of applicable work, program usage, data input process, help, explanation of terms and automatic error recovery functions that even a beginner can easily use.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.4
• /
• pp.433-445
• /
• 2014

Single phase voltage source converter (VSC) is an important power electronic converter (PEC), including single-phase voltage source inverter (VSI), single-phase voltage source rectifier (VSR), single-phase active power filter (APF) and single-phase grid-connection inverter (GCI). As the fundamental part of large scale PECs, single-phase VSC has a wide range of applications. In the paper, as first, on the basis of the concept of the discontinuous pulse-width modulation (DPWM) for three-phase VSC, a new DPWM of single-phase VSR is presented by means of zero-sequence component injection. Then, the transformation from stationary frame (abc) to rotating frame (dq) is designed after reconstructing the other orthogonal current by means of one order all-pass filter. Finally, the presented DPWM based single-phase VSR is established analyzed and simulated by means of MATLAB/SIMULINK. In addition, the DPWMs presented by D. Grahame Holmes and Thomas Lipo are discussed and simulated in brief. Obviously, the presented DPWM can also be used for single-phase VSI, GCI and APF. The simulation results show the validation of the above modulation algorithm, and the DPWM based single-phase VSR has reduced power loss and increased efficiency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37A no.9
• /
• pp.762-771
• /
• 2012

In this paper, we propose an adaptive power control scheme employing a self-optimization concept in femtocell systems, in order to improve system capacity, thereby reducing call-drop probability. In the proposed scheme, each femto base station(FBS) controls individual channel's transmission power base on two parameters; the neighboring cell's transmission power for each individual channel which is delivered from a femto-gateway and the received power strength from neighboring cells which is periodically measured by means of a spectrum sensing. Adaptive adjustment of individual channel's transmission power in accordance with femto mobile station(FMS) mobility features can also reduce undesirable handovers and evenly distribute traffic load over all femtocells. In addition, the manipulative control of channel's transmission power is able to keep the system coverage and the call-drop probability within an acceptable range, regardless of density of femtocells. Computer simulation shows that the proposed scheme outperforms existing schemes in terms of the system coverage and the call-drop probability.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.5
• /
• pp.624-631
• /
• 2012

This paper presents a high-efficiency current mode class-D(CMCD) power amplifier for the 13.56 MHz band using a Guanella's 1:1 transmission-line transformer and filtering circuits at the output network. The second and third s are filtered out in the load network of the class-D amplifier. The implemented CMCD power amplifier exhibited a power gain of 13.4 dB and a high power-added efficiency(PAE) of 84.6 % at an output power of 44.4 dBm using the 13.56 MHz CW input signal. The second and third distortion levels were -50.3 dBc and -46.4 dBc at the same output power level, respectively.