• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.5
• /
• pp.625-634
• /
• 1986

The strain distribution on a welded aluminum alloy transition joint produced by a static tensile load has been measured using a moire method combined with photoelastic coating method. The test specimens were made of aluminum alloy 6061-T6 and 2014-T6 butt welded with ER-4043 filler metal, and were post welded heat treated (solid solution heat treatment 502.deg. C 70min.) and precipitated (artificial aging 171.deg. C 600min.) to cause an abrupt change of mechanical properties between the base metals and weld metal. The photoelastic epoxy rubber was cemented on the specimen grating which had been reproduced on the specimen surface by using an electropolishing. The measurements were compared with strains computed by Finite Element Analysis. The following results were abtained. (1) The maximum strain were distributed along the center line in the transverse directiion of the weld metal. (2) The strain gradient along the fusion line increased approaching the V-groove tip and the maximum value was observed at a quarter of width from the V-groove tip. (3) The moire method combined with photoelastic coating was proved very useful for real time strain measurement in the welded aluminum alloy transition joint.

• Ceramist
• /
• v.22 no.4
• /
• pp.350-356
• /
• 2019

Recently, transition metal dichalcogenide (TMDC) monolayers have been the subject of research exploring the physical phenomenon generated by low dimensionality and high symmetry. One of the keys to understanding new physical observations is the electronic band structure of 2D TMDCs. Angle-resolved photoelectron spectroscopy (ARPES) is, to this point, the best technique for obtaining information on the electronic structure of 2D TMDCs. However, through ARPES research, obtaining the long-range well-ordered single crystal samples always proves a challenging and obstacle presenting issue, which has been limiting towards measuring the electronic band structures of samples. This is particularly true in general 2D TMDCs cases. Here, we introduce the approach, with a mathematical framework, to overcome such ARPES limitations by employing the high level of symmetry of 2D TMDCs. Their high symmetry enables measurement of the clear and sharp electronic band dispersion, which is dominated by the band dispersion of single-crystal TMDCs along the two high symmetry directions Γ-K and Γ-M. In addition, we present two important studies and observations for the direct measuring of the exciton binding energy and charge transfer of 2D TMDCs, both being established by the above novel approach.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.11
• /
• pp.1752-1756
• /
• 2006

This study explores and interprets in a new way the complex solvent and the temperature dependence of the NMR shifts for the N-$CH_2$ protons in tris(N,N-diethyldithiocarbamato) iron(III) in acetone, benzene, carbon disulfide, chloroform, dimethylformamide and pyridine. The NMR shifts are interpreted in terms of the Fermi contact interaction and the dipolar term from the multipole expansion of the interaction of the electron orbital angular momentum and the electron spin dipolar-nuclear spin angular momentum. This analysis yields a direct measure of the effect of the solvent system on the environment of the transition metal ion. The results are analysed in terms of the crystal field environment of the transition metal ion with contributions from (a) the dithiocarbamate ligand (b) the solvent molecules and (c) the interaction of the effective dipole moment of the polar solvent molecule with the transition metal ion complex.

• Applied Microscopy
• /
• v.45 no.3
• /
• pp.119-125
• /
• 2015

Two-dimensional (2D) transition metal dichalcogenides (TMDCs) have attracted significant attention due to their unique and exotic properties attributed to their low dimensionality. In particular, semiconducting 2D TMDCs such as $MoS_2$, $WS_2$, $MoSe_2$, and $WSe_2$ have been demonstrated to be feasible for various advanced electronic and optical applications. In these regards, process to synthesize high quality 2D TMDCs layers with high reliability, wafer-scale uniformity, controllable layer number and excellent electronic properties is essential in order to use 2D TMDCs in practical applications. Vapor deposition techniques, such as physical vapor deposition, chemical vapor deposition and atomic layer deposition, could be promising processes to produce high quality 2D TMDCs due to high purity, thickness controllability and thickness uniformity. In this article, we briefly review recent research trend on vapor deposition techniques to synthesize 2D TMDCs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.213-213
• /
• 2000

Direct laser vaporization of transition-metal(Co, Ni)/graphite composite pellet produced single wall carbon naotubes(SWNT) in the condensing vapor in a heated flow cylinder-type tube furnace, Transition metal/graphite composite pellet target was made by mixing graphite, Co, and Ni in 98:1:1 atomic weight ratios, pressing the mixed powder, and curing it. The target was placed in a tube furnace maintained at 1200$^{\circ}C$ and Ar inert collision gas continuously flowed into the tube. The 2nd harmonic, 532nm wavelength light from Nd-YAG laser was used to vaporize the tube. The carbon nanotubes produced by the laser vaporization were accumulated on quartz tube wall. The raw carbon nanotube materials were purified with surfactants(Triton X-100) in a ultrasonicator. These carbon nanotubes were analyzed using SEM, XRD, and Raman spectroscopic method. The carbon nanotube growth on the Ni-patterned Si substrate was investigated by the CVD process. Transition-metal, Ni and CH4 gas were used as a catalyst and a reactant gas, respectively. The structure and the phonon frequencies of the carbon nanotubes formed on the patterned Si substrate were measured by SEM and Raman spectrometer.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.1
• /
• pp.37-44
• /
• 2023

Transition metal (Me = Cu, Fe, Ni) doped (Pr, Ba)Co₂O_5+𝛿 (PBCO) material were investigated in terms of electronic structure change and electrochemical properties. It was confirmed that (Pr, Ba)(Co, Cu)O_5+𝛿 (PBCCu) and (Pr, Ba)(Co, Fe)O_5+𝛿 (PBCFe) showed cubic and orthorhombic structures, respectively, but (Pr, Ba)(Co, Ni)O_5+𝛿 (PBCNi) showed secondary phases. PBCCu has an average particle diameter of 1093 nm, and PBCO and PBCFe have an average particle diameter of 495.1 nm and 728 nm, respectively. The average oxidation values of B site ions in PBCMe were calculated to be 3.26 (PBCO), 2.48 (PBCCu), 3.32 (PBCFe), and valence band maximum (VBM) was -0.42 eV (PBCO), -0.58 eV (PBCCu), -0.11 eV (PBCFe). It is expected that PBCCu easily interacts with adsorbed oxygen due to the lowest oxidation value and the highest VBM. The polarization resistance was 0.91 Ω cm² (PBCO), 0.77 Ω cm² (PBCCu), 1.06 Ω cm² (PBCFe) at 600℃, showing the lowest polarization resistance of PBCCu.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.6
• /
• pp.1951-1956
• /
• 2011

A kinetic study is reported on nucleophilic substitution reactions of 4-nitrophenyl nicotinate 5 and isonicotinate 6 with alkali metal ethoxide EtOM (M = K, Na, and Li) in anhydrous ethanol at $25.0{\pm}0.1^{\circ}C$. Plots of pseudo-first-order rate constant $k_{obsd}$ vs. EtOM concentration exhibit upward curvature for the reactions of 5 and 6 with EtOK and EtONa but are almost linear for those with EtOLi. Dissection of $k_{obsd}$ into $k_{EtO^-}$ and $k_{EtOM}$ (i.e., the second-order rate constant for the reaction with dissociated $EtO^-$ and ion-paired EtOM, respectively) has shown that $k_{EtOK}$ ${\geq}$ $k_{EtONa}$ > $k_{EtO^-}$ but $k_{EtOLi}$ < $k_{EtO^-}$. It has been concluded that $K^+$ and $Na^+$ ions catalyze the reactions by increasing the electrophilicity of the carbonyl carbon atom through formation of a 4-membered cyclic transition state $TS_3$ or $TS_4$. However, $M^+$ ion catalysis has been found to be much less significant for the reactions of 5 and 6 than for the corresponding reactions of 4-nitrophenyl picolinate 4, which was reported to proceed through a 5-membered cyclic transition state $TS_2$. Although 5 and 6 are significantly more reactive than 4-nitrophenyl benzoate 3, the reactions of 5 and 6 result in smaller $k_{EtOK}/k_{EtO^-}$ ratios than those of 3. The electron-withdrawing ability of the nitrogen atom in the acyl moiety of 5 and 6 has been suggested to be responsible for the increase in reactivity and the decrease in the $k_{EtOK}/k_{EtO^-}$ ratio.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.5
• /
• pp.1222-1228
• /
• 2020

The adsorption and ion exchange properties of tin phosphate were studied in an aqueous solution of KCl, varing the pH and metal ion concentration in the solution. The data were explained on the basis of chemical equilibrium. Tin phosphate behaved as an acidic ion exchanger and had an adsorption selectivity toward the bivalent transition metal ions in the following order : Cu⁺² > Co⁺² > Ni⁺². As in the case of a weekly acidic exchanger, the change in hydration of metal ions played the dominant role in determining the selectivity of tin phosphate. In all cases the extent of adsorption increased with an increase in temperature and concentration. The apperance of irregular kinks in the titration curves justified the presence of several exchangeable adsorption sites with different pKa values.

• Macromolecular Research
• /
• v.15 no.3
• /
• pp.221-224
• /
• 2007

A silica-magnesium bisupport (SMB) was prepared by a sol-gel method for use as a support for a metal-locene/Ziegler-Natta hybrid catalyst. The prepared $rac-Et(Ind)_2ZrCl_2/TiCl_4$/MAO(methylaluminoxane)/SMB catalyst was applied to the copolymerization of ethylene with l-hexene using a variable triethylaluminum (TEA)/transition-metal (Ti) ratio and fixed MAO/transition-metal (Zr) ratio. The effect of the Al(TEA)/Ti ratio on the physical properties and chemical composition distributions (CCDs) of the ethylene-hexene copolymers produced by the hybrid catalyst was investigated. In the ethylene-hexene copolymers, two melting temperatures attributed to the metal-locene and Ziegler-Natta catalysts were clearly observed. The number of CCD peaks was increased from six to seven and the temperature region in which the peaks for the short chain branches of the ethylene-hexene copolymer were distributed became lower as the Al(TEA)/Ti ratio was increased from 300 to 400. Furthermore, the temperature regions corresponding to the lamellas in the copolymer became lower and those corresponding to the small lamellas in the copolymer became higher as the Al(TEA)/Ti ratio was increased from 300 to 400. In the copolymer produced with Al(TEA)/Ti = 500, however, only four CCD peaks were observed and the short chain branches were poorly distributed.

• Journal of People, Plants, and Environment
• /
• v.24 no.6
• /
• pp.585-593
• /
• 2021

Background and objective: Illegal open-air incineration, which is criticized as a leading source of air pollutants among agricultural activities, currently requires constant effort and attention. Countries around the world have been undertaking studies on the emission of heavy metal substances in fine dust discharged during the incineration process. A precise analytical method is required to examine the harmful effects of particulate pollutants on the human body. Methods: In order to simulate open-air incineration, the infrastructure needed for incineration tests complying with the United States Environmental Protection Agency (EPA) Method 5G was built, and a large-area analysis was conducted on particulate pollutants through automated scanning electron microscopy (SEM)-energy-dispersive X-ray spectroscopy (EDS). For the test specimen, high-density polyethylene (HDPE) waste collected by the DangJin Office located in Choongcheongnam-do was used. To increase the identifiability of the analyzed particles, the incineration experiment was conducted in an incinerator three times after dividing the film waste into 200 g specimens. Results: Among the metal particulate matters detected in the HDPE waste incineration test, transition metals included C (20.8-37.1 wt%) and O (33.7-37.9 wt%). As for other chemical matters, the analysis showed that metal particulate matters such as metalloids, alkali metals, alkaline earth metals, and transition metals reacted to C and C-O. Si, a representative metalloid, was detected at 14.8-20.8 wt%, showing the highest weight ratio except for C and O. Conclusion: In this study, the detection of metal chemicals in incinerated particulate matters was effectively confirmed through SEM-EDS. The results of this study verified that HDPE waste adsorbs metal chemicals originating from soil due to its own properties and deterioration, and that when incinerated, it emits particulate matters containing transition metals and other metals that contribute to the excessive production and reduction of reactive oxygen species.