• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.569-572
• /
• 2003

In VLM-ST process, the fine detailed shape processing process is needed due to the use of thick sheets for layers. The developed process perform the fine detailed shape processing in VLM-ST parts using non-contact hot tool. To predict the heat-affected zone and temperature distribution of VLM-ST parts in detailed shaping, the heat flux from the tool to the surface was calculated for the finite element analysis by modeling the tool as a heat source of radiation. The dominant process parameters such as the radiated heat input, the tool speed, and the gap between the tool tip and the foam sheet (tool height) were considered in the analysis. The results showed a good agreement with the experiments.

• Proceedings of the KWS Conference
• /
• 1996.10a
• /
• pp.148-152
• /
• 1996

A transient two-dimensional (2D) model was developed for investigating the heat and fluid flow in old pools and determining velocity profile and temperature distribution for the Gas Metal Arc (GMA) welding process. The mathematical formulation deals with the driving farces (electromagnetic, buoyancy, surface tension and plasma drag forces) as well as energy exchange between the molten filler metal droplet and weld pools. A general thermofluid-mechanics computer program, PHOENICS, was employed to numerically solve the governing equation with the associated source terms. The results of computation have shown that the electromagnetic and surface tension farces as will as the molten filler metal droplet have major influence in shaping the weld pool geometry.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.12 no.1
• /
• pp.9-22
• /
• 1975

As a second step of a thermal stress analysis in a watertight bulkhead plate during welding of a spool type penetration piece, is idealized as a thin circular disk with a clamped boundary. The exact solution for the transient temperature distribution and associated quasi-static thermal stresses which arise in a circular disk subjected to an instantaneous point source of heat acting in its interior has been obtained. And the solutions have been extended to the case of moving source of heat with the aid of the Duhamel's superposition integral and the results finally derived have been compared with the other results from the typical cases. The solutions can be applied to the problem such as a welding of a penetration piece on the watertight bulkhead and also applicable to the problems which occur in cutting or welding.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.12 no.1
• /
• pp.1-8
• /
• 1975

As a first step of a thermal stress analysis in a watertight bulkhead plate during welding of a spool type penetration piece, the bulkhead plate has been idealized as infinite plate with a circular hole. The exact solution for the transient temperature distribution and the associated quasi-static thermal stress which arise in a infinite plate subjected to an instantaneous point source of heat acting on the periphery of the circular hole. And the solutions have been extended to the case of a moving heat source with the aid of the Duhamel's superposition integral. The solutions can be applied to the problems such as a circular cutting or welding of a plate.

• Journal of Surface Science and Engineering
• /
• v.37 no.5
• /
• pp.279-288
• /
• 2004

This paper describes a three-dimensional transient finite element model for a laser cladding process. In the model, an adaptive finite element technique is used for dilution control. Using the proposed finite element model, the effects of process parameters such as scanning speed, laser's power, and preheating on the dilution of clad layer, the shape of melting pool, and the temperature distribution are calculated. It is also shown that the optimal process parameters for the required dilution can be determined from the proposed finite element model. An experiment is performed to validate the proposed model. The numerical results are compared with experimental ones.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.9 no.3
• /
• pp.161-169
• /
• 1980

In order to enhance the thermal energy storage capacity of cement mortar and to improve the effective thermal conductivity of paraffin waxes, cement- sand- paraffin wax mixture was investigated. By means of finite difference method, the transient temperature distribution in a hollow cylinder with phase change using average composite properties was obtained, and compared with experimental results. It was shown that the heat absorbed by mixture with $25\%$ paraffin fraction was as much as $50\%$ more than either a concrete mortar or pure paraffin wax in the case of ${\Delta}T=\;18.25^{\circ}C$.

• Nuclear Engineering and Technology
• /
• v.56 no.8
• /
• pp.3255-3267
• /
• 2024

This paper presents a high-fidelity simulation of the Organization for Economic Co-operation and Development (OECD) Nuclear Energy Agency (NEA) 3D whole-core Watts Bar benchmark using the UNIST in-house STREAM3D (Steady State and Transient Reactor Analysis code with Method of Characteristics) neutronic code. The benchmark encompasses various whole-core exercises, including single physics problems, multiphysics simulations, and depletion problems. When comparing parameters during the zero-power physics tests, including ITC, DBW, CRW, and criticality tests, STREAM3D results indicate a strong agreement with the measured data and KENO-VI. The comparison with the MC21/CTF code in 3D HFP BOC condition demonstrated strong agreement, with only a 0.42% difference in the normalized radial power distribution, a 0.38 K difference in the RMS of the assembly coolant exit temperature, and a mere 4 ppm difference in CBC.

• Structural Engineering and Mechanics
• /
• v.91 no.6
• /
• pp.567-581
• /
• 2024

In this paper, an effort is made to present a detailed analysis of dynamic behavior of functionally graded carbon nanotube-reinforced pipes under the influence of an accelerating moving load. Again, the material properties of the nanocomposite pipe will be determined by following the rule of mixtures, considering a specific distribution and volume fraction of CNTs within the pipe. In the present study, temperature-dependent material properties have been considered. The Navier-Stokes equations are used to determine the radial force developed by the viscous fluid. The structural analysis has been carried out based on Reddy's higher-order shear deformation shell theory. The equations of motion are derived using Hamilton's principle. The resulting differential equations are solved using the Differential Quadrature and Integral Quadrature methods, while the dynamic responses are computed with the use of Newmark's time integration scheme. These are many parameters, ranging from those connected with boundary conditions to nanotube geometrical characteristics, velocity, and acceleration of the moving load, and, last but not least, volume fraction and distribution pattern of CNTs. The results indicate that any increase in the volume fraction of CNTs will lead to a decrease in the transient deflection of the structure. It is also observed that maximum displacement occurs with an increase in the load speed, slightly delayed compared to decelerating motion.

• Structural Engineering and Mechanics
• /
• v.16 no.6
• /
• pp.695-712
• /
• 2003

The non-linear structural analysis of reinforced concrete beams in fire consists of three separate steps: (i) The estimation of the rise of surrounding air temperature due to fire; (ii) the determination of the distribution of the temperature within the beam during fire; (iii) the evaluation of the mechanical response due to simultaneous time-dependent thermal and mechanical loads. Steps (ii) and (iii) are dealt with in the present paper. We present a two-step computational procedure where a 2D transient thermal analysis over the cross-sections of beams are made first, followed by mechanical analysis of the structure. Fundamental to the accuracy of the mechanical analysis is a new planar beam finite element. The effects of plasticity in concrete, and plasticity and viscous creep in steel are taken into consideration. The properties of concrete and steel along with the values of their thermal and mechanical parameters are taken according to the European standard ENV 1992-1-2 (1995). The comparison of our numerical and full-scale experimental results shows that the proposed mechanical and 2D thermal computational procedure is capable to describe the actual response of reinforced concrete beam structures to fire.

• Journal of ILASS-Korea
• /
• v.1 no.2
• /
• pp.16-23
• /
• 1996

In case of a high-speed D.I. diesel engine. the injected fuel spray is unavoidable that the impinging on the wall of piston cavity and in this case the geometry of piston cavity has a great influence on the atomization structure and air flow fields. In the field of combustion and in many other spray applications, there are clear evidence of correlation between spray structure and emission of pollutants. Ordinary, the combustion chamber of driving engine have unsteady turbulent flow be attendant on such as the change of temperature, velocity and pressure. So the analysis of spray behavior is difficult. In this study, a single spray was impinged on each cavity wall at indicated angle in a quiescent atmosphere at room temperature and pressure, as being the simplest case, and 3 types of piston cavity such as Dish, Toroidal and Re-entrant type was tested for analyzing the influence of cavity geometry. And hot wire probe was used for analyze non-steady flow characteristics of impinging spray, and to investigate the behavior of spray, the aspects of concentration c(t), standard deviation $\sigma(t)$ and variation factor (v.f.) was measured with the lapse of time.