• Smart Structures and Systems
• /
• v.19 no.5
• /
• pp.499-512
• /
• 2017

Traditional structural dynamic analysis and Structural Health Monitoring (SHM) of large scale concrete civil structures rely on manufactured embedding transducers to obtain structural dynamic properties. However, the embedding of manufactured transducers is very expensive and low efficiency for signal acquisition. In dynamic structural analysis and SHM areas, piezoelectric transducers are more and more popular due to the advantages like quick response, low cost and adaptability to different sizes. In this paper, the applicable feasibility assessment of the designed "artificial" piezoelectric transducers called Concrete Piezoelectric Smart Module (CPSM) in dynamic structural analysis is performed via three major experiments. Experimental Modal Analysis (EMA) based on Ibrahim Time Domain (ITD) Method is applied to experimentally extract modal parameters. Numerical modal analysis by finite element method (FEM) modeling is also performed for comparison. First ten order modal parameters are identified by EMA using CPSMs, PCBs and FEM modeling. Comparisons are made between CPSMs and PCBs, between FEM and CPSMs extracted modal parameters. Results show that Power Spectral Density by CPSMs and PCBs are similar, CPSMs acquired signal amplitudes can be used to predict concrete compressive strength. Modal parameter (natural frequencies) identified from CPSMs acquired signal and PCBs acquired signal are different in a very small range (~3%), and extracted natural frequencies from CPSMs acquired signal and FEM results are in an allowable small range (~5%) as well. Therefore, CPSMs are applicable for signal acquisition of dynamic responses and can be used in dynamic modal analysis, structural health monitoring and related areas.

• Wind and Structures
• /
• v.25 no.2
• /
• pp.177-193
• /
• 2017

The accelerated development of new materials, technologies and construction processes, in parallel with advances in computational algorithms and ever growing computational power, is leading to more daring and innovative architectural and structural designs. The search for non-regular building shapes and slender structures, as alternative to the traditional architectural forms that have been prevailing in the building sector, poses important engineering challenges in the assessment of the strength and mechanical stability of non-conventional structures and systems, namely against highly variable actions as wind and seismic forces. In case of complex structures, laboratory experiments are a widely used methodology for strength assessment and loading characterization. Nevertheless, powerful numerical tools providing reliable results are also available today and able to compete with the experimental approach. In this paper the wind action on a free-form complex thin shell is investigated through 3D-CFD simulation in terms of the pressure coefficients and global forces generated. All the modelling aspects and calibrating process are described. The results obtained showed that the CFD technique is effective in the study of the wind effects on complex-shaped structures.

• The Journal of the Korea Contents Association
• /
• v.10 no.5
• /
• pp.29-36
• /
• 2010

Past clustering researches are focused on extraction of keyword for word similarity grouping. However, too many candidates to compare and compute bring high complexity, low speed and low accuracy. To overcome these weaknesses, this paper proposed a topical web document clustering model using not only keyword but also named entities such as person name, organization, location, and so on. By several experiments, we prove effects of our model compared with traditional model based on only keyword and analyze how different effects show according to characteristics of document collection.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.19 no.1
• /
• pp.13-20
• /
• 1990

Yu Ja cheong(Citron product) one of the traditional drinks was processed by a modified method to improve the quality,. Sugar(38%) and sorbitol(12%) were added as partially substi-tuted sugar and experimented about quality stability during storage at 20$\pm$2$^{\circ}C$ comparing with conventional 50% sugar added product. Chemical compositions of the acidity 40. 46mg% total Vitamin and 28.5mg% amino-N and pH was 3.7 During the storage pH reducing sugar and amino-N contents increased slightly while total acididty decreased slightly and reduced vitamin C occupied most part of total vitamin C after proessing was converted to oxidized vitamin C greatly at 70 days of storage. While L a and b values deceased in between modified one and conventional product. e value increased continually during storage {{{{ {C }_{16 { }:_{ } 0 } }}}} {{{{ {C }_{18 { }:_{ }0 } }}}} {{{{ {C}_{18 { }:_{ }1 } }}}} and {{{{ {C }_{18 { }:_{ }2 } }}}} contnts in fatty acid and citric acid itaconic acid malic acid and succinic acid in organic acid were the major componets in both products. Judging from the results of experiments during storage the quality of the modified product was compared quite well with that of vonventional one during storage.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.24-28
• /
• 2002

In a motor driving, the current rate is directly related to the rate of a switching device and in cost reduction, the parallel switching operation is the alternatives because it has the smaller current rate through current division. There are many investigations for the parallel switching operations to equaling the current division. However it remains many problems for practical usage. The reason is that the switching characteristics are mainly relied on the different saturation voltage of each device etc. and these factors are not altered by a circuit designer. In order to compensate this problem, a proper resistance is experimently inserted to the switching device. But this method can not be the optimal solution. Therefore this paper proposes a new parallel operation which uses a parallel phase winding to remove the traditional effect of switching device such as saturation voltage according to the division of current. Also the reliable and stable driving is improved through experiments and the detailed principles.

• Composites Research
• /
• v.28 no.2
• /
• pp.52-57
• /
• 2015

Soft morphing robotics making use of smart material and based on biomimetic principles are capable of continuous locomotion in harmony with its environment. Since these robots do not use traditional mechanical components, they can be built to be light weight and capable of a diverse range of locomotion. This paper illustrates a flexible smart phone robot made of smart soft composite (SSC) with inchworm-like locomotion capable of two-way linear motion. Since rigid components are embedded within the robot, bending actuators with embedded rigid segments were investigated in order to obtain the maximum bending curvature. To verify the results, a simple mechanical model of this actuator was built and compared with experimental data. After that, the flexible robot was implemented as part of a smart phone robot where the rigid components of the phone were embedded within the matrix. Then, experiments were conducted to test the smart phone robot actuation force under different deflections to verify its load carrying capability. After that, the communication between the smart phone and robot controller was implemented and a corresponding phone application was developed. The locomotion of the smart phone robot actuated through an independent controller was also tested.

• Journal of Satellite, Information and Communications
• /
• v.8 no.1
• /
• pp.77-82
• /
• 2013

The object tracking method using particle filtering has been proved successful since it is based on the Monte Carlo simulation to estimate the posterior distribution of the state vector that is nonlinear and non-Gaussian in the real-world situation. In this paper, we present two nobel methods that can improve the performance of the object tracking algorithm based on the particle filtering. First one is the feedback method that replace the low-weighted tracking sample by the estimated state vector in the previous frame. The second one is an tracking box correction method to find an confidence interval of back projection probability on the estimated candidate object area. An sample propagation equation is also presented, which is obtained by experiments. We designed well-organized test data set which reflects various challenging circumstances, and, by using it, experimental results proved that the proposed methods improves the traditional particle filter based object tracking method.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.12
• /
• pp.47-54
• /
• 2008

Hard turning process can be defined as a single-point machining process carried out on "hard" materials. The process is intended to replace or limit traditional grinding operations that are expensive, environmentally unfriendly, and inflexible. The purpose of this study is to achieve a systematic understanding of machining characteristics and the effects of machining parameters on cutting force, tool wear shape and chip formation by the outer cutting of a kind of wear resistant tungsten carbide V30. Hard turning experiments were carried out on this alloy using the PCD (Poly Crystalline Diamond), cBN (cubic Boron Nitride) and PcBN (Polycrystalline cubic Boron Nitride) cutting tools. The PcBN and the usual cBN tools were used to be compare with the PCD tool and the dry turning was carried out. The PcBN is attractive as the tool material which replaces the PCD. The tool wear width and cutting force were measured, and the worn tool and chip were observed. The difference of the tool wear mechanism among the three tool materials was investigated.

• Toxicological Research
• /
• v.29 no.4
• /
• pp.279-283
• /
• 2013

Acanthopanax koreanum Nakai, a well known traditional herb grown in Jeju Island, South of Korea, has been used as a tonic and sedative agent, as well as in the treatment of diabetes and immune diseases. Mutagenicity of two lignans, syringaresinol and tortoside A isolated from A. koreanum, was assessed using Salmonella/microsome (Ames) test. Tester strains used were Salmonella typhimurium TA98, TA100, TA1535, and Escherichia coli WP2uvrA. The mutagenic activity was determined both in the absence or presence of S9 mixture. As a result, tortoside A did not cause any increase in the number of $his^+$ revertants in S. typhimurium and E. coli WP2uvrA strains in the presence or absence of S9 mix, compared to the controls. Similarly, low concentrations of syringaresinol (750 and 1,500 ${\mu}g$/plate) did not show any mutagenic properties in all bacterial strains, in the presence or absence of S9 mixture. However, in the high concentration of syringaresinol (3,000 ${\mu}g$/plate), the number of revertants were increased in TA1535 strains, in the absence of S9 metabolic activation. Therefore, in vivo experiments such as comet assay are needed to further determine the genotoxic/carciogenic potential of syringaresinol isolated from A. koreanum.

• International Journal of Precision Engineering and Manufacturing
• /
• v.8 no.3
• /
• pp.14-19
• /
• 2007

Rapid prototyping (RP) technology can fabricate any 3D physical model regardless of geometric complexity using the layered manufacturing (LM) process. Stereolithography (SL) is the best-known example of RP technology. In general, the surface quality of a raw SL-generated part is unsatisfactory for industrial purposes due to the step artefact created by the LM process. Despite of the increased number of applications for SL parts, this side effect limits their uses. In order to improve their surface quality, additional post-machining finishing, such as traditional grinding, is required, but post-machining is time consuming and can reduce the geometric accuracy of a part. Therefore, this study proposes a post-machining technology combining coating and grinding processes to improve the surface quality of SL parts. Paraffin wax and pulp are used as the coating and grinding materials. By grinding the coating wax only up to the boundary of the part, the surface smoothness can be improved without damaging the surface. Finally, moulding and casting experiments were performed to confirm the suitability of the SL parts finished using the proposed process with rapid tooling (RT) techniques.