• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1500-1502
• /
• 1997

We investigated the tracking and erosion resistance of the silicone rubber by Inclined-Plane Method. And, with the variation of the accelerated conditions such as the applied voltage and composition of contaminant, the change of the tracking characteristics according to such conditions was evaluated. The leakage current significantly increases with the increasing voltage, but the weight loss remains almost the same. The voltage above 5.0 kV isn't recommended because tracking breakdown occurs as fast as it does without erosion, and the typical discharge waveform was the form of rectifying wave.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1560-1562
• /
• 2000

The paper reports on a study of the influence of the silicone oils on the tracking and erosion resistance and hydrophobicity of SIR. Two silicone oils(A, B) having different chemical structure were selected in consideration of goof hydrophobicity and processability. Tracking and erosion resistance of SIR was investigated by the rotating wheel dip test (RWDT). In this test tracking and erosion areas due to glow and partial arc discharges cause an increase in the leakage current with an increase in time. Leakage current of SIR was decreased with increasing ratio of oil A/B. SIR was exposed to corona discharges in air and the specimens were analyzed with contact angle. It was observed that the contact angle of SIR was increased gradually in time. The recovery of hydrophobicity was increased with increasing ratio of oil A/B.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1590-1592
• /
• 2000

The time to tracking breakdown of treated filled specimen is longer than untreated filled specimen. And, after the RWDT, the surface of specimen by adding untreated filler appeared heavy erosion. It was found that the addition to surface treated filler. the better tracking resistance. In the RWDT, the breakdown specimen is not affected by the dry flashover voltage. despite the fact that the surface degradation of tracking test has different state on each specimen. This suggests that wet flashover voltage play an important role in evaluating of tracking and erosion on the surface degradation in tracking test. And, the flashover voltage of specimen under wet conditions are greatly affected by the salt concentration and degree of degradation by the RWDT. Because of hydrophobicity and degree of degradation by the RWDT, the flashover voltage of treated filled specimen is higher than that of untreated filled specimen. Different types of specimen may have different hydrophobicity and their surface state under contaminated conditions may not be the same. It is assumed that this phenomenon is related to the decrease in hydrophobicity of the surface of the materials.

• 한국재료학회지
• /
• 제9권4호
• /
• pp.409-413
• /
• 1999

Recently, the polymeric insulators have been accepted in several countries for the outdoor high voltage applications. In comparison with the conventional porcelain, polymeric insulators offer various advantages such as light weight, superior vandal resistance and better contamination performance. The outdoor polymeric insulating materials such as silicone rubber, ethylene propylene diene monomer(EPDM), ethylene vinyl acetate(EVA) and epoxy are aged such as silicone rubber, ethylene propylene diene monomer(EPDM), ethylene vinyl acetate(EVA) and epoxy are aged under the various natural environment with the long-term performance in outdoor. In this paper, the effects of UV-under the various natural environment with the long-term performance in outdoor. In this paper, the effects of UV-ray on the surface of silicone rubber were investigated by using the weather-Ometer. The accelerated aging stresses were simulated by UV radiation, high temperature and humidity as well as water spray. These aging characteristics were examined through contact angle measurements, tracking resistance test, FT-IR and SEM/EDS analysis. The experimental results showed that tracking resistance decreases with increase in the UV-ray irradiation period. But the surface of silicone rubber kept hydrophobicity. It is found that the inorganic filler such as)$ Al(OH_3$ improves tracking resistance and the $Tio_2$is very effective in preventing degradation of silicone rubber surface from UV-ray.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권10호
• /
• pp.465-472
• /
• 2002

This paper presents a study on the aging and recovery of HTV (high temperature vulcanized) silicone rubber used for outdoor insulators. UV irradiation, corona discharge and water immersion were employed as factors of the artificial aging. The effects of changes derived from these stresses on the tracking and arc resistance of silicone rubber were examined. We have investigated the aging phenomena of HTV silicone rubber by the above stresses using the surface energy calculation with contact angle measurement, solvent-extraction, and surface/volume resistivity and so on. These results showed that UV irradiation and corona discharge lead to nearly the same surface oxidation, but the percentage change of mobile low molecular weight by these stresses was different. Furthermore, the oxidized layer induced under UV irradiation restricted the recovery of hydrophobic surface. Water immersion little lowered hydrophobicity level and leaded to a loss of tracking and arc resistance. The degradation mechanism based on our results was discussed.

• 한국전기전자재료학회논문지
• /
• 제16권11호
• /
• pp.1001-1007
• /
• 2003

The silicone fluids have been generally used as processing agent in silicone rubber(SIR) compounding. The addition of hydroxy silicone (HS) fluids to SIR for insulator housing material is required to meet the good electrical performance and the good processability. In this study, SIR with HS fluids was evaluated to investigate how the kinds of them affect insulation properties. The contact angle of the virgin sample of 40-HS SIR was low and its recovery rate was also slow. The recovery rate of 50-HS SIR was the highest being decreased with the viscosity increase of HS fluids. The tracking resistances and the corona aging resistance of 70-HS SIR and 1,040-HS SIR were excellent Tracking resistance depended largely on heat resistance of silicone fluids. But arc resistance didn't depend merely on the kind of silicone fluids.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 E
• /
• pp.1813-1815
• /
• 1997

In this study, in order to develop outdoor insulating materials, SIN(simultaneous interpenetrating polymer network) was introduced to Epoxy resin and the environment resistance was investigated. Six kinds of specimen were manufacture by filler($SiO_2$) content. SEM was untilized in order to confirm their network structure changes. Also, tracking test, UV test and acid rain test were carried out investigate the environment resistance characteristic. Therefore it was confirmed that simultaneous interpenetrating polymer network specimens were more excellent than single network structure specimens. But, acid rain almost never changed resistance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.74-77
• /
• 2001

In order to investigate the effect of salinity level on tracking characteristics of polymer insulators for distribution power systems, tracking tests were performed by tracking wheel tester under different salt concentration. In this study, 6 kinds of polymer insulators were tested under 2200 ${\mu}\textrm{s}$/cm and 4000${\mu}\textrm{s}$/cm salinity. The salinity level has a significant effect on the tracking characteristics. Namely, most polymer insulators showed the good tracking resistance in case of low salinity level. But, in case of high salinity level some polymer insulators showed the excessive erosion and tracking. These phenomena may come from the different aging mechanism. It can be concluded that too high salinity level is not desirable in aging test of polymer insulators.

• 한국화재소방학회논문지
• /
• 제29권5호
• /
• pp.57-66
• /
• 2015

본 논문은 단자대에서 단일원인 및 복합원인에 의한 전기화재위험성을 규명하기 위한 연구이다. 우선적으로 단일원인인 접촉불량에 의한 화재위험성을 측정하기 위해 조임토크변화 및 접촉저항변화에 따른 열적특성을 분석하였다. 또한, 복합원인에 의한 화재위험성을 측정하기 위해 접촉저항변화에 따른 가속트래킹 실험을 실시하여 접촉불량과 트래킹의 화재연관성을 확인하였다. 실험결과 단일원인의 경우 접촉불량상태의 조임토크 및 접촉저항 크기가 증가할수록 열적특성이 뚜렷하게 나타나는 것을 확인할 수 있었고, 접촉저항변화에 따른 열적특성이 조임토크변화에 따른 열적특성보다 그 특성이 더 잘 나타났다. 또한, 복합원인의 경우 단자대 접촉불량과 트래킹은 상호연관성을 가지고 있으며, 두 가지의 복합적인 원인이 서로 작용될 경우 기존의 단일원인의 전기화재 위험성보다 상대적인 위험성이 더욱 높게 나타나는 것으로 도출되었다.

• 대한환경공학회지
• /
• 제33권11호
• /
• pp.827-833
• /
• 2011

본 연구에서는 안산천을 대상으로 하천의 비점오염원 추적조사를 하였다. 사용된 Multiple Antibiotic Resistance Analysis (MARA) 기법은 사람과 각각의 동물의 장을 통해 배출되는 분변성 미생물들이 항생제에 대한 저항 정도가 다름을 이용하여 기지의 미생물에 대해 데이터베이스를 구축하고 미지 시료에 대해 통계적 분석을 통해 오염원을 찾아내는 방법이다. 안산천 유역을 크게 상류(축산농가지역), 중류(구시가지), 그리고 하류(신시가지) 지역으로 나누어 하천 유역의 환경적인 영향을 알아보고자 하였다. 통계 분석 결과, 가축, 애완 동물, 사람으로 구분한 3-Way 방법의 경우 45.8%가 가축으로 분류되어 상류 지역은 축산 농가 지역의 특성상 동물에 의한 영향이 큰 것으로 판단할 수 있었다. 중류는 구시가지 지역으로써 인간의 영향이 60% 이상으로 나타났으며, 하류 지역 역시 신시가지 지역으로 인간의 영향이 80% 이상으로 나타났다. 실제 현장 조사를 근거로 예상할 수 있었던 비점오염원과 MARA를 통한 분석 결과가 매우 일치하는 모습을 통해 비점오염원 추적을 위한 MARA기법의 유용성을 판단할 수 있었으며, 각 지역의 특성에 맞는 데이터 베이스 구축을 통해 효과적인 비점오염원의 추적이 가능할 것으로 기대된다.