• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.1
• /
• pp.158-165
• /
• 2008

Hydraulic power steering system has been adopted in seniority passenger and commercial vehicle system for an easy maneuverability and a smoother ride. In this study, hydraulic power steering system analysis model which includes hydraulics and mechanical sub-systems was developed using commercial software, AMESim in order to predict characteristics for various steering components. Each component which constructs system was modeled and verified by experimentally obtained characteristics curves of each components. The agreement between simulation and experimental results shows the validity of the simulation model. The parameter sensitivity analysis such as valve opening area, torsional stiffness for system design are carried out by the analysis and experimental method.

• International Journal of Control, Automation, and Systems
• /
• v.5 no.1
• /
• pp.35-42
• /
• 2007

This paper presents an INS(Inertial Navigation System) grade, surface micro-machined differential resonant accelerometer(DRXL) manufactured by an epitaxially grown thick poly silicon process. The proposed DRXL system generates a differential digital output upon an applied acceleration, in which frequency transition is measured due to gap dependent electrical stiffness change. To facilitate the resonance dynamics of the electromechanical system, the micromachined DRXL device is packaged by using the wafer level vacuum sealing process. To test the DRXL performance, a nonlinear self-oscillation loop is designed based on the extended describing function technique. The oscillation loop is implemented using discrete electronic elements including precision charge amplifier and hard feedback nonlinearity. The performance test of the DRXL system shows that the sensitivity of the accelerometer is 24 Hz/g and its long term bias stability is about 2 mg($1{\sigma}$) with dynamic range of ${\sigma}70g$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.213-216
• /
• 2005

A numerical analysis was performed for interior connections of continuous flat plate to analyze the effect of design parameters such as column section shape, gravity load and slab span on the behavioral characteristics of the connections. Through the parametric study, the variations of shear stress distribution around the connection were investigated. According to the result of numerical analysis, as the length of the cross section of column in the direction of lateral load increases and gravity load increases, the effective area and the maximum shear strength providing the torsional resistance decrease considerably. And as the slab span loaded with relatively large gravity load increases, the negative moment around the connection increases and therefore the strength of connection against unbalanced moment decreases.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.815-817
• /
• 1999

In the two-mass system driving a load through a flexible shaft or transmission system, a shaft torsional vibration is often generated. In this case, it's difficult to control only by conventional PI controller. To solve this problem. the two-mass speed control system with PID controller is designed by using pole assignment method, and an optimum PID parameters are derived by evaluating ITAE(Integral of time multiplied by the absolute error) performance index. Simulation results show the validity of the proposed PID controller and this controller is compared with the conventional PID controller.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.49-52
• /
• 1999

Substituting composite structures for conventional metallic structures has many advantages because of higher specific stiffness and specific strength of composite materials. In this work, one-piece propeller shafts composed of carbon/epoxy composite and glass/epoxy one were designed and manufactured for a rear wheel drive automobile, which uses generally a steel two-piece propeller shaft. From the tests of the composite propeller shafts, it was found that the propeller shafts satisfied requirements of static torque transmission capability, torsional buckling capability and the first natural bending frequency and had 40% weight saving effect compared with steel propeller shaft.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1816-1822
• /
• 2000

The maximum and mean indicated pressure of two stroke low speed diesel engine has been continuously increased with a view of increasing engine power and also reducing fuel consumption. As a result, axial excitation has been highed comparing to that of the previous and so in standard axial vibration damper is applied to all two stroke low speed diesel engine at the free end of crankshaft. Though many studies were carried out for marine use, few has been made for diesel power plant because there was little demand for power plant. Nowadays, diesel engine is much to be used for many benefits and so in this paper, the optimum design of axial vibration on the 65 MW diesel power plant with 9K80MC-S engine was carried out. And the axial-torsional coupled vibration of this shafting system is identified by theoretical analysis and vibration measurement.

• Journal of the Korea Concrete Institute
• /
• v.12 no.5
• /
• pp.13-23
• /
• 2000

In this study, an flexural test on half-scale spliced PSC-I girder was conducted to verify the efficiency of the long span spliced girder as suggested by the Korean Highway Design Specification. The experimental results showed that the specimens developed a complex failure mode due to flexural-compression and torsional stress. The cracking moment of each girder was higher the experiment than was calulated by the ACI and the ultimate strength were the almost same. To estimate the safety and the structural efficiency of the spliced girder, the proposed Yielding Resistance Index(YRI) and ductility index by American Concrete Institutes were used based on the energy concept. The proposed YRI defined the ratio of crack resisting energy and the total energy calculated from load-displacement relationship. Based on the analysis of YRI and ductility index, the flexural behavior of the spliced girder was found to be efficient. Through the experimental results, the structural behavior of proposed spliced PSC I-type girder for long span bridge was found to be more efficient than the exsisting PSC I-type girders.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1950-1953
• /
• 1996

A $1\;{\times}\;4$ micro mirror array is designed and fabricated. In contrast to other micro mirrors which utilize torsional flexure hinges or cantilevers for restoring torque and supporting purpose, we have placed a substrate hinge structure under each mirror. Each micro mirror consists of address electrode, substrate hinge consisting of pin and staple, supporter post, and mirror plate. Electrical connection between mirror plate and ground electrode is established by substrate hinge. Mirror undergoes a rotational motion due to electrostatic force when voltage difference is applied between address electrode and mirror plate. Micro mirrors with two different types of staple shape and two different pin sizes are designed and fabricated. Each mirror is designed to have ${\pm}\;10^{\circ}$ of deflection angle and have $100\;{\times}\;110\;{\mu}m^2$ of size.

• Journal of Mechanical Science and Technology
• /
• v.16 no.4
• /
• pp.485-491
• /
• 2002

The gyroscopes have been used as a suitable inertial instrument for the navigation guidance and attitude controls. The accuracy as very sensitive sensor is limited by the lock-in region (dead band) by the frequency coupling between two counter-propagating waves at low rotation rates. This frequency coupling gives no phase difference and an angular increment is not detected. This problem can be overcome by the mechanical dithering. The purpose of the mechanical dithering is to suppress the dead band, oscillate the monoblock about the rotation axis and add an external rotation rate. This paper presents the theoretical considerations of the mechanical performances of dither on the basis of the loading condition and angular characteristics due to the piezoelement deformation and the validity of theoretical equations are compared through FEM (Finite Element Method) simulations.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.155-160
• /
• 2008

Using a three-dimensional (3-D) FE analyses, this paper provides the shape optimization of the standard test specimen for the torsion test, as well as a method for analyzing effects of misalignment under the angular and concentric misalignment. For verification, FE analysis is performed, which is designed for the perfectly full-model. To optimize the design shape of the torsion-controlled fatigue test specimen, we performed sensitivity analysis using shape parameters. Additionally, two kinds of misalignment (angular misalignment and concentric misalignment) are applied to the circular and tubular specimens to show effects of misalignments in the FE analysis. The present results will provide valuable information for designing shafts for every kind of mechanical system under torsional force.