• Computers and Concrete
• /
• v.28 no.5
• /
• pp.487-495
• /
• 2021

The use of prestressed concrete box girder bridges built by segmentally balanced cantilevers has bloomed in the last decades due to its significant structural and construction advantages in complex topographies. In Colombia, this typology is the most common solution for structures with spans ranging of 80-200 m. Despite its popularity, excessive deflections in bridges worldwide evidenced that time-dependent effects were underestimated. This problem has led to the constant updating of the creep and shrinkage models in international code standards. Differences observed between design processes of box girder bridges of the Colombian code and Eurocode, led to the need for a validation of in-service status of these structures. This study analyzes the long-term behavior of the Tablazo bridge with data scarcity. The measured leveling of this structure is compared with a finite-element model that consider the most widely used creep and shrinkage models in the literature. Finally, an adjusted model evidence excessive deflection on the bridge after six years. Monitoring of this bridge typology in Colombia and updating of the current design code is recommended.

• Journal of Korea Water Resources Association
• /
• v.55 no.9
• /
• pp.645-655
• /
• 2022

Recently rip currents are frequently observed in the summer at the beaches located along the East Sea coast. To understand the generation types of rip currents occurred at the Ease Sea beaches, numerical simulations of rip currents over the topographies of the Sokcho, Naksan, Gyeongpo, Mangsang beaches were performed by using a Boussinesq-type wave and current model, FUNWAVE. The offshore and nearshore topographically-controlled rip currents and the transient rip currents were well reproduced due to the alongshore non-uniformities involving the phase interaction effects. This study looked over the generation types of rip currents to occur at the beaches with complicated field bathymetries.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.223-223
• /
• 2012

Surface engineering plays a significant role in fabricating highly functionalized materials applicable to industrial and biomedical fields. Surface wrinkles and folds formed by ion beam or plasma treatment are buckling-induced patterns and controlled formation of those patterns has recently gained considerable attention as a way of creating well-defined surface topographies for a wide range of applications. Surface wrinkles and folds can be observed when a stiff thin layer attached to a compliant substrate undergoes compression and plasma treatment is one of the techniques that can form stiff thin layers on compliant polymeric substrates, such as poly (dimethylsiloxane) (PDMS). Here, we report two effective methods using plasma modification techniques for controlling the formation of surface wrinkles and folds on flat or patterned PDMS substrates. First, we show a method of creating wrinkled diamond-like carbon (DLC) film on grooved PDMS substrates. Grooved PDMS substrates fabricated by a molding method using a grooved master prepared by photolithography and a dry etching process were treated with argon plasma and subsequently coated with DLC film, which resulted in the formation of wrinkled DLC film aligning perpendicular to the steps of the pre-patterned ridges. The wavelength and the amplitude of the wrinkled DLC film exhibited variation in the submicron- to micron-scale range according to the duration of argon plasma pre-treatment. Second, we present a method for controlled formation of folds on flat PDMS substrates treated with oxygen plasma under large compressive strains. Flat PDMS substrates were strained uniaxially and then treated with oxygen plasma, resulting in the formation of surface wrinkles at smaller strain levels, which evolved into surface folds at larger strain levels. Our results demonstrate that we can control the formation and evolution of surface folds simply by controlling the pre-strain applied to the substrates and/or the duration of oxygen plasma treatment.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.2
• /
• pp.75-84
• /
• 2016

PURPOSE. To evaluate the effect of various surface treatments on the surface structure and shear bond strength (SBS) of different ceramics. MATERIALS AND METHODS. 288 specimens (lithium-disilicate, leucite-reinforced, and glass infiltrated zirconia) were first divided into two groups according to the resin cement used, and were later divided into four groups according to the given surface treatments: G1 (hydrofluoric acid (HF)+silane), G2 (silane alone-no heat-treatment), G3 (silane alone-then dried with $60^{\circ}C$ heat-treatment), and G4 (silane alonethen dried with $100^{\circ}C$ heat-treatment). Two different adhesive luting systems were applied onto the ceramic discs in all groups. SBS (in MPa) was calculated from the failure load per bonded area (in $N/mm^2$). Subsequently, one specimen from each group was prepared for SEM evaluation of the separated-resin-ceramic interface. RESULTS. SBS values of G1 were significantly higher than those of the other groups in the lithium disilicate ceramic and leucite reinforced ceramic, and the SBS values of G4 and G1 were significantly higher than those of G2 and G3 in glass infiltrated zirconia. The three-way ANOVA revealed that the SBS values were significantly affected by the type of resin cement (P<.001). FIN ceramics had the highest rate of cohesive failure on the ceramic surfaces than other ceramic groups. AFM images showed that the surface treatment groups exhibited similar topographies, except the group treated with HF. CONCLUSION. The heat treatment was not sufficient to achieve high SBS values as compared with HF acid etching. The surface topography of ceramics was affected by surface treatments.

• Wind and Structures
• /
• v.22 no.4
• /
• pp.477-501
• /
• 2016

Though hilly topography influences both wind speeds and directions aloft, only the influence on wind speeds, i.e. the speed-up effect, has been thoroughly investigated. Due to the importance of a model showing the spatial variations of wind directions above hilly terrains, it is worthwhile to systematically assess the applicability and limitations of the model describing the influence of hilly topographies on wind directions. Based on wind-tunnel test results, a model, which describes the horizontal and vertical variations of the wind directions separately, has been proposed in a companion paper. CFD (Computational Fluid Dynamics) techniques were employed in the present paper to evaluate the applicability of the proposed model. From the investigation, it has been found that the model is acceptable for describing the vertical variation of wind directions by a shallow hill whose primary-to-secondary axis ratio (aspect ratio) is larger than 1. When the overall hill slope exceeds $20^{\circ}$, the proposed model should be used with caution. When the aspect ratio is less than 1, the proposed model is less accurate in predicting the spatial variation of wind directions in the wake zone in a separated flow. In addition, it has been found that local slope of a hill has significant impact on the applicability of the proposed model. Specifically, the proposed model is only applicable when local slope of a hill varies gradually from 0 (at the hill foot) to the maximum value (at the mid-slope point) and then to 0 (at the hill top).

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.25 no.2
• /
• pp.151-163
• /
• 1992

Seasonal variations of water mass distributions in the Yellow Sea, the East China Sea, and the adjecent seas of Cehju Island, are investigated. A common seasonal variation over these whole areas is shown. Warm and saline waters are extended northwestward into the Yellow Sea in winter and retreated back southeastward to the East China Sea in summer. Barotropic numerical model results suggest that monsoon winds could drive such seasonal variations. Upwind flows play an important role in the processes. In the numerical model results, upwind flows are shifted to China. It is due to energy dissipations by complicated coast lines and shallow bottom topographies in the northern part of the Yellow Sea. The shifted routes of upwind flows agrees well with that of the southward extensions of the Yellow sea Bottom Cold Waters in summer.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.239-239
• /
• 2006

In the present study, we synthesized CBDA-FDA and its analogue, poly(4,4' -(9,9-fluorenyl)diphenylene pyromellitimide) (PMDA-FDA), and then investigated quantitatively the orientational distributions of the polymer chain segments in the surfaces of their films by using linearly polarized Fourier transform infrared (FTIR) spectroscopy and optical retardation analysis. We also examined the films' surface topographies using high spatial resolution atomic force microscopy (AFM). Further, rubbed films were used to assemble antiparallel and $90^{\circ}-twisted$ nematic (TN) LC cells, and the alignment behaviors, pretilt angles and anchoring energies of the LC molecules in the cells were determined. The films were found to have very interesting surface morphologies and LC alignment behaviors, which have not previously been reported. The observed LC alignments, pretilt angles and anchoring energies are discussed by taking into account the interactions of the LC molecules with the oriented polymer chain segments and the surface morphologies.

• Korean Journal of Soil Science and Fertilizer
• /
• v.49 no.4
• /
• pp.310-317
• /
• 2016

This study aimed to evaluate the nutrient load balance from rice paddy fields with different topographies, alluvial plain and local valley. Continuous monitoring from May to September, 2013 was conducted for water quantification and qualification from alluvial plain in Yeoju region (32 ha) and local valley in Jincheon region (24 ha). The discharge rates of T-N from the alluvial plain were 57.2, 5.84, 22.7, and $5.20kg\;ha^{-1}$ for irrigation, precipitation, drainage, and percolation, respectively. In case of local valley, T-N loads were 34.6, 4.73, 21.1, and $4.15kg\;ha^{-1}$ for irrigation, precipitation, drainage, and percolation, respectively. In contrary, the T-P loads from the alluvial plain were 2.23, 2.22, 2.54, and $0.41kg\;ha^{-1}$ for irrigation, precipitation, drainage, and percolation, respectively. In case of local valley, T-P loads were 1.44, 1.57, 1.82, and $0.34kg\;ha^{-1}$ for irrigation, precipitation, drainage, and percolation, respectively. The nutrient contents in drainage water were influenced by the amount of waters, rainfall, and surface drainage water. The Pearson correlation analysis showed that rainfall was significantly correlated with nutrient loads from July to August due to the amount of runoff in local valley paddy field, and irrigation was related with nutrient loads of drainage from July to August. This study showed that paddy rice farming in alluvial plain and local valley might be beneficial to water quality protection.

• Journal of the Korean earth science society
• /
• v.26 no.3
• /
• pp.218-231
• /
• 2005

The purpose of this study was to investigate essential information about the geological and geomorphological characteristics of the Odaesan landscape, in order to efficiently preserve and develop resources selected from among that are highly valuable scholastically and esthetically. A total of 147 geological and geomorphological landscape resources were studied during the course of this study. Landscape type mostly discovered was the tectonic topography, followed by the topographies of weathering, river, mountain, lacustrine, and periglacier, respectively in decreasing order. Among the varieties of geological and geomorphological landscape resources, 4 outcrops were utilized as tourist resources and 5 outcrops were considered as valuable sites for scientific research. Geological and geomorphological landscape resources for academic research were considered to have practical uses such as geological and geomorphological fieldwork for students and thematic geotourism courses for the public.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.25 no.6
• /
• pp.443-456
• /
• 1992

For a linear double shelf bottom topography as in the Yellow Sea, the dispersion relation of coastally trapped waves is derived for the general case Including high-frequency and short waves and for the case of low-frequency and long waves. With linear bottom topography, the governing equation is Bessel's equation for the latter case but Hummer's equation for the former case. Hypergeometric Functions, which are the solutions of Hummer's equation, are derived and converted to various special functions for the limiting cases. On a double shelf topography, the divergence effects of horizontal flow are important for the wave dynamics, irrespective of cross-shelf dimensions, while on a single shelf they are usually neglected when the cross-shelf dimension is much smaller than the Rossby deformation radius. The divergence effect allows the existence of Kelvin wave and reduces the phase speeds of continental shelf waves. Finally, the frictionless eigenfunctions are proved to be orthogonal.