• 한국세라믹학회지
• /
• 제50권6호
• /
• pp.454-459
• /
• 2013

Recently, remote phosphors have been reported for application to white LEDs to provide enhanced phosphor efficiency compared with conventional phosphor-based white LEDs. In this study, a remote phosphor was produced by coating via screen printing on a glass substrate with different numbers of phosphor coating. The paste consists of phosphor, lowest softening glass frits, and organic binders. The remote phosphor could be well controlled by varying the phosphor content rated paste. After mounting the remote phosphor on top of a blue LED chip, CCT, CRI, and luminance efficiency were measured and values of 5300 K, 62, and 117 lm/W were respectively obtained in the 80 wt% phosphor with 3 coating layers sintered at $800^{\circ}C$.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.149-149
• /
• 2010

The double-layer antireflection (DLAR) coatings have significant advantages over single-layer antireflection (SLAR) coatings. This is because they will be able to cover a broad range of the solar spectrum which would enhance the overall performance of solar cells. Moreover films deposited at high frequency are expected to show excellent and UV-stable passivation in the refractive index that we adopted. In this work, we present a novel DLAR coating using SiNx:H thin films with refractive indices 1.9 and 2.3 as the top and bottom layers. This approach is cost effective when compared to earlier DLAR coatings with two different materials. SiNx:H films were deposited by Plasma enhanced chemical vapor deposition (PECVD) technique using $SiH_4$, $NH_3$ and $N_2$ gases with flow rates 20~80sccm, 200sccm and 85 sccm respectively. The RF power, plasma frequency and substrate temperature for the deposition were 300W, 13.56 MHz and $450^{\circ}C$, respectively. The optimum thickness and refractive indices values for DLAR coatings were estimated theoretically using Macleod simulation software as 82.24 nm for 1.9 and 68.58 nm for 2.3 respectively. Solar cells were fabricated with SLAR and DLAR coatings of SiNx:H films and compared the cell efficacy. SiNx:H> films deposited at a substrate temperature of $450^{\circ}C$ and that at 300 W power showed best effective minority carrier lifetime around $50.8\;{\mu}s$. Average reflectance values of SLAR coatings with refractive indices 1.9, 2.05 and 2.3 were 10.1%, 9.66% and 9.33% respectively. In contrast, optimized DLAR coating showed a reflectance value as low as 8.98% in the wavelength range 300nm - 1100nm.

• 한국표면공학회지
• /
• 제31권3호
• /
• pp.133-141
• /
• 1998

Stainless is widely used for various purposes due to its good corrosion resistance. There has been much research to produce the color stainless steel by several methods. In this experiment, TixN films have been deposited on the SUS304 substrate by the DC magnetron sputtering system and the color and texture of the films as a function of coating conditions has been studies. The TixN films showed a (111) preferred orintation in bias-free conditions. The texture of coated later was changed from (111) to (200) to (2200 with a change of the bias from -1000V to -3000V. When the bias is low, coated elements have low energy. Therefore, the texturct (111) of low surface energy. The mobility of atoms was increased with the increase of the blas and texture was changed to the other plane. Non-etched specimens all exhibited strong (111) texture. This result shows that (111) is a loose plane and of non-etched specimens all exhibited. High growing velocity of (111) of especially was main texture of Non-etched specimens. Low working pressure($4\times10^{-3}$torr) was more effective than figh working pressure ($6\times10^{-3}$torr) for the gold color of $Ti_xN$ film. L and b were increased and a was decreased with the increase of bias voltage. Accordingly, We obtained the near gold color of $Ti_xN$ film(L;92, a;1~1.5 b:24~29.50. As a result of reflectance. And as the bias increased, the reflectance was proportional to the increasing bias voltage, but we took the top reflectance when the bias voltage was -200V.

• 한국건설순환자원학회논문집
• /
• 제12권2호
• /
• pp.128-134
• /
• 2024

아스팔트계 교면용 방수재료는 방수재 상부에 고온의 아스콘이 타설되는 과정에서 재료가 연질화나 액상화되어 방수층의 불균형 및 두께감소 등이 문제점으로 남아있는 실정이며, 이를 해결하기 위하여 신규 재료의 개발과 도입 등 기존의 재료를 벗어난 해결방안이 요구되고 있다. 따라서 본 연구에서는 교면용 도막방수재의 기본물성을 만족한 MMA 도막방수재를 기준으로 전체 품질기준에 대한 물성을 파악하고 바탕 콘크리트, 방수재 및 포장층이 시스템화 된 상태에서의 품질기준 등을 확인하여 교면에 MMA 도막방수재로써 활용 가능 여부를 확인하였고, 그 결과 MMA 도막방수재는 경질 MMA 수지 : 연질 MMA 수지 : 파우더 = 6 : 34 : 60의 배합비를 통하여 안정적인 토목구조물 교면용 MMA 도막방수재의 적용이 가능할 것으로 판단되며, MMA 도막방수재와 아스콘간의 이질재료의 부착은 경화 특성을 가지는 유화 아스팔트를 활용하여 시공할 경우 국토교통부 '아스팔트 콘크리트 포장 시공 지침(2021.07)'의 최소 품질기준을 만족할 것으로 판단된다.

• 한국결정성장학회지
• /
• 제6권3호
• /
• pp.463-470
• /
• 1996

알파 알루미나와 철이 첨가된 티타니아 최종층으로 구성된 세라믹 여과막을 졸-겔방법으로 제조하였다. 철이 첨가된 지지 티타니아 복합여과막은 지지체를 혼합졸에 침지하여 제조하였다. 복합여과막을 $550^{\circ}C$에서 $850^{\circ}C$까지 열처리온도에 따르는 미세구조 변화를 주사전자현미경으로 조사하였다. $650^{\circ}C$에서 1시간 소결한 경우, 철이 첨기된 티타니아 복합여과막의 평균입자 크기는 약 40 nm이었다. 철이 첨가된 티나니아 복합여과막은 티타니아 복합여과막보다 열적 저항성이 우수하였다. 철이 첨가된 티타니아 복합여과막은 $650^{\circ}C$까지 균열이 없는 미세구조와 좁은 입도분포를 유지하였다.

• Composites Research
• /
• 제35권2호
• /
• pp.80-85
• /
• 2022

본 연구에서는 항공기 방빙을 위해서 탄소계 소수성 입자인 탄소나노튜브의 코팅 횟수에 따른 테프론-폴리우레탄 탑코트의 나노입자 부착력과 표면 소수성 특성을 평가하기 위하여 실험을 진행하였다. 나노입자 부착력을 측정하기 위해서 인발접착시험을 진행하였고, 표면소수성 특성을 측정하기 위해서 정적접촉각 시험과 거칠기 평가를 진행하였다. 거칠기평가를 통하여 탄소나노튜브가 테프론-폴리우레탄 탑코트에 함침된 정도를 할 수 있었고, USB-현미경을 통하여 테프론-폴리우레탄 탑코트에 탄소나노튜브가 함침 및 분산정도를 확인하였다. 그 결과 코팅횟수가 많을수록 탄소나노튜브가 응집되고 이에 의하여 접착력이 감소한다는 것을 확인하였다. 실험결과 코팅 횟수에 따라 테프론-폴리우레탄의 소수성은 커지고 접착력은 감소하였다. 그로 인해 테프론-폴리우레탄 탑코트 와의 접착력 향상과 최적화된 소수성을 가지는 탄소나노튜브의 코팅횟수를 파악할 수 있었다.

• 한국세라믹학회지
• /
• 제32권3호
• /
• pp.349-358
• /
• 1995

The ceramic composite membrane was synthesized by thermal oxidation after evaporation of Al on the support prepared by slip casting process. Oxidation was performed at $700^{\circ}C$ and 80$0^{\circ}C$ under dry oxygen atmosphere. It was considered as optimum oxidation condition that the membrane showed a knudsen behaviro. A further oxidation resulted in an increase of gas permeability because top layer became densified. Then, a multi-layered composite membrane was synthesized through a sol-gel method, evaporation and thermal oxidation of Al coating processes. While the membrane was thermally stable up to 80$0^{\circ}C$, gas permeability was rapidly decreased even at a slight amount of deposition of Al.

• 한국전기전자재료학회논문지
• /
• 제27권11호
• /
• pp.740-745
• /
• 2014

ZnO nanowires were grown by hydrothermal synthesis process and piezoelectric poly vinylidene fluoride (PVDF) was then coated on top of the ZnO-nanowires by spray-coating technique. The composite layer of ZnO-nanowires/PVDF was applied to an energy harvesting device based on piezoelectric-conversion mechanism. A defined mechanical force was given to the nanogenerator device to evaluate their electric power generation characteristics, where output current density and voltage were examined. Electric power generation property of the ZnO-nanowires/PVDF based nanogenerator device was compared to that of the nanogenerator device with ZnO-nanowires as single active layer. Effect of the ZnO-nanowires on improvement of power generation was discussed to examine its feasibility for the nanogenerator device.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1342_1342
• /
• 2009

Zinc tin oxide (ZTO) based thin-film transistors (TFTs) were fabricated on glass substrate by using sol-gel method. The fabricated ZTO TFT had bottom gate and top contact structure with ZTO layer formed by spin coating from ZTO solution. The fabricated TFT showed field-effect mobility of about 2 - $4\;cm^2/V{\cdot}s$ with on/off current ratios >$10^7$, and threshold voltage of 2 V.

• 한국인쇄학회지
• /
• 제14권1호
• /
• pp.1-15
• /
• 1996

In this paper, the preparation of lead zirconium titanate(PZT) thin film by sol-gel processing was descried. Thin film coated with thickness of 4${\mu}{\textrm}{m}$ on the stainless steel substrates using the multiple spin-coating process. The crystalline phases of PZT powder and film were investigated by X-ray diffraction pattern and PZT thin film has perovskite structure over 600 C annealing temperature. Corona charging characteristics of the ferroelectric PZT thin film at 600 C were investigated by electrophotographic measurement. A difference in the charging characteristics between positive and negative corona charging was found. The charge acceptance depended in the polarity of corona and the poling of film. According to the D-E hysteresis measurment, PZT thin film can be poled by corona charging without use of top electrode. The remnant polarization in the PZT thin film is generally in the order of 48$\mu$C/$\textrm{cm}^2$. From this results, the ferroelectric PZT thin film will be possible to apply for the add-on type imaging formation.