• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.2
• /
• pp.147-152
• /
• 2002

Carbon nitride thin films were deposited by reactive sputtering for the hard coating materials on Si wafer and tool steels. When the nitrogen content of carbon nitride film on tool steel is 33.4%, the mean hardness and elastic modulus are 49.34 GPa and 307.2 GPa respectively. The nitrided or carburised surface acts as the diffusion barrier which shows better adhesion of carbon nitride thin film on the steel surface. To prevent nitrogen diffusion from the film, steel substrate can be saturated by nitrogen forming a Fe$_3$N layer. The desirable structure at the surface after carburising is martensite, but sometimes, due to high carbon content an proeutectoid Fe$_3$C structure may form at the grain boundaries, leaving the overall surface brittle and may cause defects.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1130-1131
• /
• 2006

We found that the """interface reaction between Ni-based alloy bond, diamond, and steel core is very critical in bond strength of diamond tool. None element from metal bond diffuses into the steel core but the Fe element of steel core was easily diffused into the bond. This diffusion depth of Fe has a great effect on the bonding strength. The Cr in steel core accelerated the Fe diffusion and improved the bond strength, on the other hand, carbon decreased the strength. Ni-based alloy bond including Cr was chemically bonded with diamond by forming Cr carbide. However, the Cr and Fe in STS304 were largely interdiffused, the strength was very low. The Cr passivity layer formed at surface of STS304 made worse strength at commissure in brazing process.

• Korean Journal of Metals and Materials
• /
• v.47 no.5
• /
• pp.267-273
• /
• 2009

Three types of structural intermetallic compounds, $Ni_3Al$, NiAl and TiAl, having each single phase structure without pores were produced by arc-melting process. Their sliding wear properties were investigated against a hardened tool steel. It was shown that the wear of the intermetallic compounds was hardly occurred against the hardened tool steel. TiAl compound showed the best wear resistance among them. In this case, wear was preferentially occurred on the surface of the hardened tool steel of the mating material which has higher hardness. It could be found that the wear mode on intermetallics without pores by arc-melting process was different from that on its porous layer coated on steel by combustion synthesis.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.12
• /
• pp.198-203
• /
• 1999

In this study, chip-tool friction and shear characteristics of cold drawn free machining steels in turning were assessed. To do this, a newly developed equivalent oblique cutting model was adopted. And for comparison with those of free machining steels, chip-tool friction and shear characteristics of conventional carbon steels were also investigated. The Pb-S free machining steel shows superior machinability to others. In case of the Bi-S free machining steel, the shear stress and the specific friction energy are relatively lower than those of conventional carbon steels, but its shear strain is relatively high, so it does not show any remarkable improvement of machinability.

• Journal of the Korean Society for Heat Treatment
• /
• v.5 no.3
• /
• pp.165-170
• /
• 1992

The chip controls are investigated experimentally for the purpose of estimating cutting ability of hardened steel. In this experiment, hardened STD11 steel ($HR_c$ 60) is turned with carbide tool M20 under various cutting conditions and with several tool shapes. The main results obtained are as follows : 1) Cutting conditions of cutting speed 45m/min. feed 0.09-0.13 rev. depth of cut 0.4-0.6 are recommended for the chip excluding. 2) In case that the feed becomes larger and a lead angle of cutting tool becomes smaller, the chip excluding becomes easier. 3) It is confirmed that frank wear and crator wear on the cutting tool appear severely from about 10 min. after cutting start and chip excluding get worse.

• Transactions of Materials Processing
• /
• v.26 no.6
• /
• pp.372-377
• /
• 2017

In this paper, an effective design procedure was proposed to design the rib of die structure for auto-body member with ultra-high strength steel (UHSS) having ultimate tensile strength (UTS) of 1.5 GPa. From analysis results of the die structure, structural safety of the die was evaluated with information such as displacement and von-Mises stress. It was concluded that the casting part could be designed in order to reduce tool deformation. A design guideline of the die structure was proposed, especially for the rib structure in the casting part with an optimization scheme and local reinforcement concept. Simulation result following the design guideline fully explained that stability of the tool structure could be obtained simultaneously with weight minimization.

• Transactions of Materials Processing
• /
• v.29 no.6
• /
• pp.338-346
• /
• 2020

A V-bending test was performed in order to predict springback of high-strength steel sheets under various conditions. The results of V-Bending test were analyzed with artificial neural networks and FE-simulation, respectively, for the tool design. The results of design are discussed. The bending test result using the tool designed with artificial neural networks was about 92˚. However, the bending test result using the tool designed FE-simulation was about 94.5˚. Artificial neural networks are a useful tool along with FE-simulation in predicting springback.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.213-214
• /
• 2009

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.541-542
• /
• 2009

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.125-126
• /
• 2007