• Journal of the Korean Society for Precision Engineering
• /
• v.5 no.4
• /
• pp.59-65
• /
• 1988

This paper describes the transmutation layer of CNC Wire electrical discharte machined surface. In order to analayze and invesigate transmutation layer of the carbon tool steel, workpieces was heat-treated by quenching, tempering, normaling. The obtained results are summarized as follows. 1. The result showed that wire electrical discharge machined surface region was transmuted into the recdast layer in the range of about 10${\mu}$m deep by resolidification and next zone was transmuted into the heat affected zone in the range of about 15${\mu}$m deep by high temperature. 2. The hardness of the recast layer and heat affected zone was decreased on its machined surface. 3. The more wire feedrate was increased, the more electrical discharge machine gap was decreased.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.158-160
• /
• 2007

The butt and lap configurational friction stir welding of type 304 stainless steel was conducted in this study. The sound joints were obtained by WC tool. As the welding distance increased, tool deformation gradually increased at the pin edge. The discoloration by oxidation was observed at the top surface of the joint, a sufficient heat-input was required to avoid the welding defect owing to the lack of stirring at the welding start point. Very fine grains were observed in the stir zone, and the grain coarsening was not observed in the heat affected zone.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.1
• /
• pp.123-133
• /
• 1996

From the experimental study of wire-cut Electric Discharge Machining of alloyed tool steel and tungsten carbide, the characteristics such as cutting speed, surface roughness has been observed and evaluated for various conditions. Cutting speed is improved as peak discharge current and wire tension become increased, and gap voltage and spark cycle decreased. Surface roughness can be better when peak discharge current and gap voltage become smaller, or spark cycle and wire tension become larger. Secondary cut is recommended to obtain high precision and good quality.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.4
• /
• pp.315-323
• /
• 1998

This study has been conducted to develope the combined heat treating technique of gas carburising - gas nitriding and gas carburising to improve the hot working performance of type H3 hot work tool steel. Case depth and carbrides coarsening were increased with increasing carburising temperature and time, respectively. Surface hardness showed decreasing tendency with increasing 2nd tempering temperature after carburising treatment. After carburising, 2nd treatment at 500 to 600 was chosen according to a hardness demand of final product. High temperature tempering resistance showed more excellent quality during such carburising-nitriding or carburising than complex treatment as after conventional hardening.

• Korean Journal of Computational Design and Engineering
• /
• v.8 no.3
• /
• pp.150-156
• /
• 2003

Direct Metal Deposition (DMD) is a new additive process producing three-dimensional metal components or tools directly from CAD data, which aims to take mold making and metalworking in an entirely new direction. It is the blending of five common technologies: lasers, CAD, CAM, sensors and materials. In the resulting process, alternatively called laser cladding, an industrial laser is used to locally heat a spot on a tool-steel work piece or platform, forming a molten pool of metal. A small stream of powdered tool-steel metal is then injected into the metal pool to increase the size of the molten pool. By moving the laser beam back and forth, under CNC control, and tracing out a pattern determined by a computerized CAD design, the solid metal part is eventually built line-by-line, one layer at a time. DMD produces improved material properties in less time and at a lower cost than is possible with traditional fabrication technologies.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.3
• /
• pp.87-92
• /
• 2006

The characteristic of interface layer and the effect of bias voltage on the microstructure of c-BN films were studied in the microwave plasma hot filament C.V.D process. c-BN films were deposited on a high speed steel(SKH-51) substrate by hot filament CVD technique assisted with a microwave plasma to develop a high performance of resistance coating tool. c-BN films were obtained at a gas pressure of 20 Torr, vias voltage of 300 V and substrate temperature of $800^{\circ}C$ in $B_2H_6-NH_3-H_2$ gas system. It was found that a thin layer of hexagonal boron nitride(h-BN) phase exists at the interface between c-BN layer and substrate.

• Journal of Ocean Engineering and Technology
• /
• v.13 no.1 s.31
• /
• pp.70-78
• /
• 1999

오늘날 기계공업 현장에서 심공드릴가공은 광범위한 응용과 양호한 생산성으로 인하여 그 요구가 증가 되고 있다. 그러므로, 본 연구는 난삭재인 SKD11고합금공구강을 여러가지 절삭조건하에서 BTA드릴가공하여 얻은 실험결과(표면조도, 진직도, 진원도, 원통도, 구멍확대량, 등)를 다루었으며 이들의 이론적 배경과 실험을 비교 분석하였다. 프레스금형 부품과 기계부품으로 사용되고 있는 SKD11고합금공구강은 기계가공이 힘든 난삭재료로서 그 어려움이 크므로 본 연구는 생산현장에 보다 나은 심공드릴가공결과와 관련 지식을 제공 할수 있다고 사료된다.

• Journal of the Korean Society of Safety
• /
• v.11 no.3
• /
• pp.59-65
• /
• 1996

This study is to evaluate dynamic fracture characteristics of alloy tool steel, STD-11, according to various tempering conditions (heat treatment). The dynamic fracture initiation toughness and some of the dynamic fracturing characteristics were evaluated by using the instrumented Charpy impact testing procedures. The distributions of Victors hardness and dynamic fracture initiation toughness with respect to varying tempering temperatures are found to be symmetric type with the help of experimental results for the STD-11. It is also found that the dynamic fracture initiation toughness is a inverse proportion to Vickers hardness. In this experimental study, it is found that the best heat treatment condition is 55$0^{\circ}C$ tempering in alloy tool steel, STD-11, because the results show high values of Vickers hardness and dynamic fracture initiation toughness.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.502-506
• /
• 2001

This paper presents a new method for cutting steel with a diamond tool using electrolysis. The electrolysis is adopted in the diamond cutting to prevent the high chemical activity between a diamond tool and an iron-based workpiece. The basic principle of the method is to oxdize a thin substrate of the workpiece by electrolysis ahead of the diamond tool which cuts the oxidized layer. A desired shape can be obtained by repeating this process. The cutting force is reduced because the diamond tool removes only the weakened material by electroysis. The reduction of the cutting force suppresses the excessive wear of the diamond tool. The oxidization penetrates several micrometers in depth along the previously formed shape. The corrosion rates depend on current density and make suggestions on the optimum cutting conditions.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.2
• /
• pp.87-95
• /
• 2000

By using AIP(Arc Ion Plating) of a physical vapor deposition for the first time in Korea a ceramic tool whose surface is coated single layeredly with TiN is developed. In addition cutting resistance appearing in the process of finishing cut of hardened carbon tool steel STC3 is studied. The principal and radial components of cutting resistance in those cutting conditions appear to be the same or similar and the feed component is relatively small. The feed component is found to be in proportion to cutting width and the radial component in proportion to cutting thickness. Owing to coating the cutting resistance of a TiN coated ceramic tool increas-es compared with that of a general ceramic tool.