• Clean Technology
• /
• v.19 no.2
• /
• pp.75-83
• /
• 2013

In the present paper, we review recycling and applications of titanium binary alloy scraps. The recycling techniques are to successfully prepare low oxygen content ingots using hydrogen plasma arc melting (HPAM) and to produce low oxygen content titanium alloy powders by Hydrogenation-dehydrogenation (HDH) and Deoxidation in solid state (DOSS) process. In addition, as applications of the titanium binary alloy scraps, Ti based solid-solution carbide powders, which would be used for producing Ti based solid-solution cermets with high toughness, were prepared using the titanium binary alloy scraps. These results confirmed that the titanium alloy scraps could be recycled and refined using the HPAM. The resulting oxygen content of the titanium alloy powders were below 1,000 ppm after powderizing. Finally, we had confirmed that the refined titanium alloy powders were able to be utilized as raw materials for preparing the toughened cermets.

• Resources Recycling
• /
• v.26 no.6
• /
• pp.3-9
• /
• 2017

In this study, plasma arc remelting behaviors according to arc current, arc voltage, and types of plasma gas were investigated using Kroll processed Ti sponges as anode. In the discharge pressure range of vacuum pump ($200{\sim}300kgf/cm^2$), the arc voltage did not vary greatly with the increase of discharge pressure at a given arc length. This means that the pressure in the vacuum chamber during operation hardly changes and the atmospheric pressure maintains. Under various conditions of arc currents (700~900A), the arc voltage slightly increased with arc current. The effects of anode materials and operational variables on the arc length-arc voltage relationship were compared with the results in previous studies. When the atmospheric gas changed from argon to helium, double effect of improvement on the output of the steady state was observed. The increase of output in the plasma arc device was accompanied by an increase in the melting rate of the Ti sponge and the quality of the ingot surface was also improved. The plasma arc remelting of the new scrap titanium and the old scrap zirconium alloy could result in the fabrication of an ingot with high surface quality.

• Journal of Powder Materials
• /
• v.20 no.6
• /
• pp.467-473
• /
• 2013

This research presents a preparation method of dental components by metal injection molding process (MIM process) using titanium scrap. About $20{\mu}m$ sized spherical titanium powders for MIM process were successfully prepared by a novel dehydrogenation and spheroidization method using in-situ radio frequency thermal plasma treatment. The effects of MIM process parameters on the mechanical and biological properties of dental components were investigated and the optimum condition was obtained. After sintering at $1250^{\circ}C$ for 1 hour in vacuum, the hardness and the tensile strength of MIMed titanium components were 289 Hv and 584 MPa, respectively. Prepared titanium dental components were not cytotoxic and they showed a good cell proliferation property.

• Resources Recycling
• /
• v.30 no.2
• /
• pp.46-52
• /
• 2021

Off-grade Ti generated from smelting and mechanical processing has a high oxygen content. In this work, off-grade Ti was deoxidized using Mg and a chloride mixture as the reductant and flux, respectively. The experiments were conducted in the α-Ti temperature range (1,023~1,123 K) and the effects of the reaction time, reaction temperature, quantitiy of Mg and chloride ratio on deoxidation were investigated. Notably, when YCl3 is used as the flux to react with MgO, it is possible to reduce the activity of MgO. Therefore Ti can be deoxidized using Mg. In this study, the O content was decreased from 0.5 wt% to 0.1004 wt% at 1073 K, for 6 hours, with Mg=3.6 g and $X_{YCl_3}=0.22$.

• Resources Recycling
• /
• v.33 no.1
• /
• pp.22-30
• /
• 2024

To synthesize the Ti₃AlC₂ MAX phase, a crucial precursor for generating the two-dimensional material MXene, the use of Ti scrap as an initial material is an economically feasible approach. This study aims to optimize the synthesis conditions for the phase fraction of the Ti₃AlC₂ MAX phase utilizing Ti scrap as the Ti source. The deoxidation of Ti powders, prepared through the hydrogenation-dehydrogenation process from Ti scrap, was effectively accomplished using the deoxidation in solid-state (DOSS) process. The optimal synthesis conditions were established by blending DOSS-Ti, Al, and graphite powders with particle sizes ranging from 25 ~ 32 ㎛ in a molar ratio of 3:1.1:2. The resulting phase fractions were as follows: Ti₃AlC₂ at 97.25 wt.%, TiC at 0.93 wt.%, and Al₃Ti at 1.82 wt.%. Furthermore, the oxygen content of the Ti₃AlC₂ MAX powder, spanning from 25 ~ 45 ㎛, was measured at 4,210 ppm.

• Resources Recycling
• /
• v.21 no.5
• /
• pp.58-64
• /
• 2012

Ti button type ingots were prepared by recycling of Ti turning scraps using vacuum arc melting process for production of consumable arc electrode. The behavior of impurities such as Fe, W, O, and N in the Ti button ingots was investigated and the properties of the Ti button ingots were also evaluated. In the case of oxygen gaseous impurity, the oxygen layers on the surface of the Ti turning scraps were easily removed by the first vacuum arc melting. On the other hand, the solute oxygen in the Ti turning scraps was not removed by the next melting. In the case of Fe, major impurity in the Ti turning scraps, the removal degree in the final Ti button ingot refined by vacuum arc melting for 20 minutes was approximately 43 %, which is due to the vapor pressure difference between Ti and Fe. As a result, the Ti button ingots with ASTM grade 3 could be obtained by multiple vacuum arc melting from the Ti turning scraps. Therefore, it was confirmed that the preparation of consumable electrode for vacuum arc remelting could be possible by recycling of Ti turning scraps.

• Resources Recycling
• /
• v.21 no.1
• /
• pp.60-65
• /
• 2012

The Ti-6Al-4V alloys were prepared by recycling of dental Ti pure scraps using vacuum arc melting process, and their physical properties were evaluated the Ti-6Al-4V alloys with different oxygen concentrations. For the preparation of Ti-6Al-4V alloys, Ti pure scraps used for dental implant were utilized as a raw material, and their different oxygen concentrations were ranged from G1 to G4 grade in ASTM standards. It was confirmed that the weight loss of Al in the composition of Ti-6Al-4V alloy could be controlled under the Ar pressure of 875 torr during the melting of alloy. The oxygen concentrations of the Ti-6Al-4V alloys were ranged from 1170 to 3340 ppm. The vickers hardness change of the Ti-6Al-4V alloys showed a similar behavior with that of pure Ti. As a result, we confirmed a possibility of preparation of Ti-6Al-4V alloy by recycling of dental Ti scraps using vacuum arc melting process in this study.