• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.371-374
• /
• 2009

This paper presents a cooling system using thermoelectron for improving the output of BIPV module. The temperature characteristic in regard to improving the output of BIPV system has rarely been studied up to now but some researchers only presented the method using a ventilator. The cooling system efficiency of BIPV module applied to a ventilator mainly depends on the weather such as wind, insolation etc. Because the cooling system of BIPV module using a ventilator is so sensitive, that is being set off by wind speed at all time but is unable to operate in the NOCT(Nominal Operating Cell Temperature) which is able to make the maximum output The paper presents the cooling system using thermoelectron so as to solve such problems. The temperature control of thermoelectron can be controlled independently in the outside environment because that is performed by micro-controller. The temperature control of thermoelectron, also, can be operated around NOCT through algorism of the temperature control. Therefore, outputs of the whole system increase and the efficiency rises. The paper demonstrates the validity of proposed method by comparing the data obtained through a experiment of the cooling method of BIPV using a ventilator and proposed thermoelectron.

• Journal of Power System Engineering
• /
• v.5 no.3
• /
• pp.95-103
• /
• 2001

This study is applied to common induction motor, and vector control is realized by using an indirect type of induction motor which has a simple composition. In this study extended Kalman filter is used from control theoretical viewpoint, and primary resistance and secondary resistance which change according to the temperature of motor are simultaneously estimated. This paper aims to research an indirect vector control in which the secondary resistance obtained from this estimation is consistent with secondary flux. This estimation is made by on-line estimation, but on-line estimation is difficult because extended Kalman filter takes long time in computation time. So off-line estimation was made on the assumption that the variation of temperature in motor is slow temporally.

• Journal of Power System Engineering
• /
• v.19 no.3
• /
• pp.48-54
• /
• 2015

This paper introduced a design method of soldering station that can control two types of soldering iron heater. At design time, to distinguish two types of soldering iron heater the voltage divider rule has been applied, and the distinguished resistor is inserted to handler of soldering iron to prevent misuse by users. And an algorithm to design a PID controllers is proposed. The proposed controllers parameter which can be easily realized, and are designed by using the input output data from systems, and have outstanding ability making the output response of nonlinear systems similar to the desired one. Temperature control experiments were performed to verify the ability of the suggested controller. As a result, suggested PID controller followed the desired ones, and one soldering station can control the various type of soldering irons in real time.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.11
• /
• pp.1072-1078
• /
• 2001

The real time optimal control algorithm of the DDC controller for chilled water and supply air temperature set-point of heating, ventilating, air-conditioning and refrigeration systems has been researched for minimization of the total power which is consumed by the chiller, chilled water pump and air handing unit fan. The study has been done by using TRNSYS program in order to analyze the central cooling system in terms of the environmental variables such as indoor cooling lead and wet-bulb temperature. This optimal control alogorithm saves more energy and is suitable for real time on-line control in comparison with conventional method.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.77-80
• /
• 1997

In this paper presented is a temperature controller for a semiconductor test handler. Using ARMAX model and least square method, the chamber model for the design of a controller is identified through experiment. With the identified model an LQG/LTR controller is designed. Experiment with a real test handler demonstrated good performance in that its overshoot is small and response time is fast.

• Proceedings of the KIPE Conference
• /
• 2017.11a
• /
• pp.83-84
• /
• 2017

The heat treatment performed during the welding of the structure should adjust the temperature of the structure in several steps in order to further improve the welding performance. This paper proposes a technique to control multiple SCR power converters to control the temperature of each ceramic heater at various stages according to a specified time.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.413-422
• /
• 2000

Samples of banana were dried in a two-stage heat pump dryer capable of producing stepwise control of the inlet drying air temperature while keeping absolute humidity constant. Two stepwise air temperature profiles were tested. The incremental temperature step change in temperature of the drying air about the mean air temperature of 30 $^{\circ}C$ was 5 $^{\circ}C$. The total drying time for each temperature-time profile was about 300 minutes. The drying kinetics and color change of the products dried under these stepwise variation of the inlet air temperature were measured and compared with constant air temperature drying. The stepwise air temperature variation was found to yield better quality product in terms of color of the dried product. Further, it was found that by employing a step-down temperature profile, it was possible to reduce the drying time to reach the desired moisture content.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.43 no.3
• /
• pp.147-151
• /
• 1998

The conductivity test is a measure of electrolytes leakage from plant tissue. The shorter the maturation period after heading was the greater electrical conductivity (EC) of rice seed. The polymer-coated seed was not different in EC compared with non-coated seed. As soaking time of rice seed increased, EC increased gradually. The EC varied from 9.9 to 20.7$\mu$S $cm^{-1}g^{-l}$ for control plots and from 21.3 to 41.7$\mu$S $cm^{-1}g^{-l}$ for heat-killed seeds which were produced by autoclaving seeds at 121$^{\circ}C$ for 20 minutes. The germination speed (the rate of 5th day) of rice seed was 94% at control plot, 83% at low temperature and 20% at high temperature. Besides, germination percentage was 95% for the control, 92% for the low temperature treatment and 39% for the high temperature treatment. The EC was negatively correlated (r=-0.771$^{**}$) with germination percentage at low temperature. Water uptake in seeds of 30, 40, 50 days after heading (DAH) was greater than that of 20 DAH. Plant height of seedlings was 9.84 cm for the control but 4.32 cm for the high temperature treatment, and the tallest for polymer-coated seed. Dry weight of seedlings was 0.841 g for the control and 0.287 g at high temperature. Besides, the polymer-coated seed was heavier than non-coated seed. The number of roots was largest from 40 to 50 DAH and polymer-coated seed, but was decreased from 20 to 30 DAH. The length of roots was 20.52 cm at control plot and 19.89 cm polymer-coated seed but 8.68 cm for the low temperature treatment and 7.28 cm for the high temperature treatment.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.279-283
• /
• 2000

Lime is one of the world's most useful chemicals and manufactured in various types of kilns, using various fuels. Quicklimes vary in reactivity with water due to variations in the time and temperature calcining process and type of kiln used. Careful attention and control of time and temperature in the calcining process is necessary to insure a highly reactive lime. Excess time and temperature will cause the lime to be over burned. The highest reactivity of quicklime is obtained by calcination of limestone in the particle size of 0.1cm~2cm, calcination temperature of $1000^{\circ}C$, calcination time 90min. It was found by the scanning electron microscopes that pores of quick lime is reducted if the soft burned quick lime is heated continually.

• Journal of Biosystems Engineering
• /
• v.33 no.2
• /
• pp.130-135
• /
• 2008

The purpose of this study was to develop a preprocessor for real-time portable quality evaluation system of milk. The preprocessor consisted of two flow pump to supply milk sample and reaction reagent at given volume, a fan to mix milk with reaction reagent, a thermoelectric device to maintain sample temperatures of $40^{\circ}C$, and I/O interface to control signals. The tests conducted with different level of flow rate of pump, fan speed, ambient temperature, and intial temperature of mixtures. To evaluate performance of the preprocessor, the supplied volumes, color changes, and temperatures were measured and analyzed. The results showed that the preprocessor could control supplying volumes, mixing, temperatures of samples automatically. The preprocessor showed good performance to be used for portable quality evaluation system of milk.