• Proceedings of the KIEE Conference
• /
• 1997.07a
• /
• pp.270-272
• /
• 1997

Superconducting wire is quenching as soon as transport current exceeded the critical current value. However transport current exceeded the critical current value, quench is not generated immediately. In this paper, the results of the theoretical study for time delay of quench phenomenon are described.

• Journal of the Korean Electrochemical Society
• /
• v.17 no.2
• /
• pp.119-123
• /
• 2014

Here I report on how Fourier Transform Electrochemical Impedance Spectroscopy (FTEIS) overcomes the potential-current linearity problem encountered in the impedance calculation process. FTEIS was first invented to solve the time-related drawback of the conventional impedance technique. The dramatic time reduction of FTEIS enabled the real-time impedance measurement but brought about the linearity problem at the same time. While the conventional method circumvents the problem using the steady-state made by a sufficiently long measurement time, FTEIS cannot because of its real-time function. However, according to the mathematical development reported in this article, the potential step used in FTEIS is proved to avoid the linearity problem. During the step period, the potential and the current are linearized by the electrochemical impedance. Also, Fourier transform of the differentiated potential and current is proved to give the same result of the original ones.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.36T no.1
• /
• pp.13-18
• /
• 1999

The trap density by the stress bias in silicon oxides with different thicknesses has been investigated. The trap density by stress bias was shown to be composed of on time current and off time current. The on time trap density was composed of dc current. The off time trap density was caused by the tunneling charging and discharging of the trap in the interfaces. The on time trap density was used to estimate to the limitations on oxide thicknesses. The off time trap density was used to estimate the data retention in nonvolatile memory devices.

• Journal of Welding and Joining
• /
• v.16 no.6
• /
• pp.52-58
• /
• 1998

The effect of Si content in welding wires on th arc stability was investigate, in the region of short circuit transfer and spray transfer. In the region of short circuit transfer, with increasing Si content, average arcing time and average short circuit time were increased. Therefore, droplet transfer frequency was decreased, due to the increase of arcing time and peak current at the moment of arc-reiginition was increased, due to the increase of short circuit time. In the region of spray transfer, the fluctuations of arc current and arc voltage was the most stable in wire with Si content of about 00.60 wt.%.

• Proceedings of the Korea Society of Information Technology Applications Conference
• /
• 2005.11a
• /
• pp.99-102
• /
• 2005

In the paper, a proposed VCO based on bondwire inductances and nMOS varactors was implemented in a standard $0.25\;{\mu}m$ CMOS process. Using the new drain current model and a propagation delay time model equations, the operation speed of CMOS gate will predict the dependence on the load capacitance and the depth of oxide, threshold voltage, the supply voltage, the channel length. This paper describes the result of simulation which calculated a gate propagation delay time by using new drain current model and a propagation delay time model. At the result, When the reverse bias voltage on the substrate changes from 0 voltage to 3 voltage, the propagation delay time is appeared the delay from 0.8 nsec to 1 nsec. When the reverse voltage is biased on the substrate, for reducing the speed delay time, a supply voltage has to reduce. The $g_m$ value of MOSFET is calculated by using new drain current model.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2715-2720
• /
• 1999

To prevent the short circuit of upper and lower arms of bridge type PWM converters as like a voltage source inverter and PWM AC/DC converter, the dead time is inserted in between two switching signals. As a result, unexpected errors are occurred. In this paper, a new dead time minimization method is proposed. According to the proposed method, very short time which is equal to the applied dead time or more short than it, is adopted at the time of current polarity is changing. Moreover, it can be operated with the polarity information of reference current in case of current control. With the experimental results. the varidity of proposed method is verified.

• Journal of Environmental Science International
• /
• v.7 no.3
• /
• pp.311-320
• /
• 1998

The volume transport and turnover time of the Deukryang Bay. located at the southern area of Korea, were calculated based on the current meter(RCM-7,ACM 16M) data observed at the three gateways of the tegrating observed data and then averaging on time. dangdo and Kogumdo. The total water volume transports through three entrances of the bay in May and October were $3.9{\times}10-2Sv, 3.4{\times}10^{-2}Sv(1Sv=10^6m^3s^{-1}$) and turnover time were 0.97day, 1.12day, respectively. Semidiurnal tides were predominant (70~85%). The water volume transports by residual currents were 2~4% of total water volume transports . The average fraction of fresh water calculated by tidal prism method using salinity difference between inflow current and outflow current through three entrances In Deukryang Bay was about 0.06% of total volume and the flushing time of fresh water was estimated as 0.97day.

• Journal of Welding and Joining
• /
• v.17 no.1
• /
• pp.55-61
• /
• 1999

The effect of S content in welding wires on the arc stability was investigated, in the region of short circuit transfer and spray transfer. In the region of short circuit transfer, with increasing S content, average arcing time and average short circuit time were decreased. Therefore, droplet transfer frequency was increased, due to the reduction of arcing time and peak current at the moment of arc-reiginition was decreased, due to the decrease of short circuit time. In the region of spray transfer, the fluctuation degree of arc current and arc voltage became more stable, with increasing S content.

• Journal of Welding and Joining
• /
• v.33 no.2
• /
• pp.47-55
• /
• 2015

With using adaptive control of the resistance spot welding machine, the advantage on electrode life time for galvanized steels has been addressed. This study was aimed to evaluate the electrode life time of galvanized steels with applying the constant current control and the adaptive control resistance spot welding process for a comparison purpose. The growth in diameter of electrode face was similar for both the constant current and the adaptive control up to 2000 welds. The button diameter was decreased with weld numbers, however, sudden increase in button diameter with use of the adaptive control after 1500 welds was observed. The peak load was continuously decreased with increasing number of welds for both the constant current and the adaptive control. The current compensation during a weld was observed with using the adaptive control after 1800 welds since the ${\beta}$-peak on dynamic resistance curve was detected at later weld time. The current compensation with adaptive control during resistance spot welding enhanced the nugget diameter at the faying interface of steel sheets and improved the penetration to thinner steel sheet.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.1
• /
• pp.56-63
• /
• 2003

This paper studies that torque model considered with decaying phase back-EMF is different In conduction and commutation period and analyzes the torque pulsation components mathematically. In this paper, it is proposed a novel method to suppress torque pulsation due to commutation time. First, it propose commutation delay time control method, which is to compensate current slope of rising phase and decaying phase to control commutation time. Current ripple is minimized at non-commutating current and torque ripple is reduced below critical speed range that dc link voltage is the same as four times of back-EMF voltage. However, torque ripple still exists due to the relation with back-EMF and commutating current and it is increased on a large scale above critical speed range, especially. Secondly, proposed method is commutation time control, which is considered with torque pulsation due to the relation of back-EMF and commutating current. Through the proposed method, the torque pulsation can be minimized in the whole speed range as well as range over critical speed.