• Journal of Institute of Convergence Technology
• /
• v.1 no.1
• /
• pp.18-23
• /
• 2011

Shaping an input command through considering the resonant modes of multi degrees of freedom system, it is possible to realize the wanted motion, without exciting the uncontrollable modes of the flexible system. But, an increase of modes to be considered brings inevitably about the time delay due to an excessive rising time. On the purpose of reducing the rising time, only the interesting and dominant modes can be considered to determine the timing pulses of input shaper. In this paper, an effect of shaper by the partial modes is analysed for a specific system and the input shapers by the partial modes are analysed for three d.o.f damped system, using Matlab simulation.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.90-95
• /
• 2007

In order to investigate the optimum condition of the autofrettage process for the diesel engine injection pipe, different values of autofrettage pressure, pressure rising time, pressure holding time, and repetition of autofrettage process were applied. Autofrettage was preformed by applying the hydrostatic internal pressures of 603 MPa, 535 MPa, 500 MPa on the fuel injection pipe, corresponding to theoretically 50%, 30%, and 20% overstrain levels, respectively. The autofrettage residual stresses in the injection pipe were experimentally determined by using X-ray diffractometer. As the overstrain level increased, the magnitude of compressive residual stress at the bore increased. It was found that the rising time to reach the autofrettage pressure, holding time at the autofrettage pressure, and repeating application of the autofrettage pressure on the pipe had no significant influence on the residual stress distributions.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.6
• /
• pp.1121-1128
• /
• 2011

The HEMP has very short rising time with several tens of kV/m, and very dangerous to almost of the electronics. And the certain level of EMP shielding effectiveness is necessary for mos t of the systems andequipment. In EMP shielding effectiveness, the peak value and the rising time in the system are the most considerable parameters. In order to find out these parameters, we need to estimate the pulse shape in time domain. In this paper, we propose the methods to estimate the penetrated pulse in time domain using measured shielding effectiveness and digital filter modeling technique. The validity of the Digital filter modeling technique is verified by the HFSS.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.1
• /
• pp.29-35
• /
• 2019

As the fourth industrial revolution is emerging, many companies are increasingly interested in smart factories and the importance of sensors is being emphasized. In the case that sensors for collecting sensing data fail, the plant could not be optimized and further it could not be operated properly, which may incur a financial loss. For this purpose, it is necessary to diagnose the status of sensors to prevent sensor' fault. In the paper, we propose a scheme to diagnose digital-sensor' fault by analyzing the rising time and falling time of digital sensors through the LSTM(Long Short Term Memory) of Deep Learning RNN algorithm. Experimental results of the proposed scheme are compared with those of rule-based fault diagnosis algorithm in terms of AUC(Area Under the Curve) of accuracy and ROC(Receiver Operating Characteristic) curve. Experimental results show that the proposed system has better and more stable performance than the rule-based fault diagnosis algorithm.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.7 no.2
• /
• pp.101-111
• /
• 2012

In the ALC(Autoclaved lightweight concrete) manufacturing process, if the pre-cured semi-cake is removed after proper time is passed, it will be hard to retain the moisture and be easily cracked. Therefore, in this research, we took the research by multiple regression analysis to find relationship between variables for the prediction the hardness that is the control standard of the removal time. We study the relationship between Independent variables such as the V/T(Vibration Time), V/T movement, expansion height, curing time, placing temperature, Rising and C/S ratio and the Dependent variables, the hardness by multiple regression analysis. In this study, first, we calculated regression equation by the regression analysis, then we tried phased regression analysis, best subset regression analysis and residual analysis. At last, we could verify curing time, placing temperature, Rising and C/S ratio influence to the hardness by the estimated regression equation.

• Journal of the Korean Society of Safety
• /
• v.9 no.1
• /
• pp.76-82
• /
• 1994

Combustion phenomena(characteristics) of organic solvents including various alcohols Immobilized on ceramic balls were studied. Experiments were performed by burning methyl, ethyl, and propyl alcohol immobilized on sands (particle size 0.35mm) and coramic balls(particle size 1~5mm) to measure mass burning rate, height burning rate and combustion temperature. The longer time from ignition to extinguishment was resualted from the larger particle size of ceramic balls and the smaller size of ceramic balls exhibited the higher mass burning rate. Of alcohols tested the relative magnitude of facilitation of combustion was methyl >ethyl >propyl. Combustion temperatare of alcohols, without regard to the types of alcohols, was not increased with smaller ceramic balls(up to 3mm of particle size). However, with larger ceramic balls, combustion temperatare of alcohols was increased by 40~5$0^{\circ}C$ and the highest combustion temperatare was obtained with sands(particle size 0.35mm). Also, second rising was occurred at the combustion time of I5-20min. and this second rising time was increased with the smaller particle. These results will be able to be used for petrochemical industries using particles to evaluate the danger of fire and explosion.

• Proceedings of the KAIS Fall Conference
• /
• 2009.05a
• /
• pp.450-453
• /
• 2009

Compositional design and optimization of processing parameters are key factors for controlling and improving the properties of SiC-based electroconductive ceramic composites. Compare economic estimation of SiC ceramic heater with sheathe heater are as followings. (1) Temperature rising time of sheath heater is 1.1 times faster than SiC ceramic heater. (2) Heating insulation of SiC ceramic heater is 2.7 times larger than sheath heater. If SiC ceramic heater is one body type of a product application, contact resistance will decrease. I think that temperature initial rising time is faster than now. The more SiC ceramic heater is used for a long time, the more economic benefit is larger in the view point of heat insulation.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1174-1180
• /
• 2015

We investigate in this paper the radiated electromagnetic waves together with the discharge characteristics of Trichel pulse of negative DC corona discharge in air in pin-to-plate and wire-to-plate configurations. The feature of the current pulse and the frequency spectrum of the electromagnetic radiations were measured under various pressures and gas gaps. The results show that the repetition frequency and the amplitude of Trichel pulse current depend on the discharge conditions, but the rising time of the pulse relates only to the radius of needle or wire and keeps constant even if the other conditions (including the discharge current, the gas gap and the gas pressure) change. There exists the characterized spectrum of electromagnetic waves from negative corona discharge in Trichel pulse regime. These characterized radiations do not change their frequency at a given cathode geometry even if the averaged current, the gas gap or the air pressure changes, but the amplitude of radiations changes accordingly. The characterized electromagnetic radiations from Trichel pulse corona relate to the formation or the rising edge of current pulse. It confirms that the characterized radiations from Trichel pulse supply information of discharge system and provide a potential method for detecting charged targets.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.469-470
• /
• 2008

We have studied electro-optic characteristics as a function of splay elastic constants ($K_{11}$) in the fringe-field switching (FFS) mode using the LC with positive dielectric anisotropy. When $K_{11}$ is increased from 7.7pN to 11.7pN, a maximum transmittance is slightly increased and rising time become a little bit fast. However, operating voltage and threshold voltage is independent. In opposition to rising time, decay time is not affected by $K_{11}$. We already know that $K_{11}$ affects tilt angle of liquid crystals. Therefore, on the occasion of high $K_{11}$, liquid crystals are mainly affected by twist deformation because the higher $K_{11}$, the less tilt angle. In the FFS device, high $K_{11}$ is favorable to reduce tilt angle in on state and thus improve rising response time.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1171-1176
• /
• 2004

To develop and improve a switchgear, the prediction of the pressure rising within the switchgear is very important. This study investigates the pressure rising characteristics of switchgear in order to evaluate the result of arc fault test. The pressure rising time at the four points of measurement calculated by CFD is well accord with the experimental results. The maximum pressure within the switchgear estimated by CFD is about 1.0bar, the pressure from experiment is 0.7 bar. The results of this study are able to be used to improve the performance of existing switchgear and to develop a new type switchgear.