• Fibers and Polymers
• /
• v.6 no.1
• /
• pp.19-27
• /
• 2005

High-speed melt spinning of syndiotactic polystyrene was carried out using high and low molecular weight poly­mers, HM s-PS and LM s-PS, at the throughput rates of 3 and 6 g/min. The effect of take-up velocity on the structure and properties of as-spun fibers was investigated. Wide angle X-ray diffraction (WAXD) patterns of the as-spun fibers revealed that the orientation-induced crystallization started to occur at the take-up velocities of 2-3 km/min. The crystal modification was a-form. Birefringence of as-spun fibers showed negative value, and the absolute value of birefringence increased with an increase in the take-up velocity. The cold crystallization temperature analyzed through the differential scanning calorimetry (OSC) decreased with an increase in the take-up velocity in the low speed region, whereas as the melting temperature increased after the on-set of orientation-induced crystallization. It was found that the fiber structure development proceeded from lower take-up velocities when the spinning conditions of higher molecular weight and lower throughput rate were adopted. The highest tensile modulus of 6.5 GPa was obtained for the fibers prepared at the spinning conditions of LM s-PS, 6 g/min and 5 km/min, whereas the highest tensile strength of 160 MPa was obtained for the HM s-PS fibers at the take-up velocity of 2 km/min. Elongation at break of as-spun fibers showed an abrupt increase, which was regarded as the brittle-duc­tile transition, in the low speed region, and subsequently decreased with an increase in the take-up velocity. There was a uni­versal relation between the thermal and mechanical properties of as-spun fibers and the birefringence of as-spun fibers when the fibers were still amorphous. The orientation-induced crystallization was found to start when the birefringence reached -0.02. After the starting of the orientation-induced crystallization, thermal and mechanical properties of as-spun fibers with similar level of birefringence varied significantly depending on the processing conditions.

• Nuclear Engineering and Technology
• /
• v.5 no.1
• /
• pp.55-64
• /
• 1973

The effect of compression in the strain ageing of Ferrovac E iron has been examined with compressive testing following the prestrain in compression. Both prestraining and testing were preformed at room temperature with the strain rate of 1.9$\times$10$^{-4}$ se $c^{-1}$ and that of 0.95$\times$10$^{-4}$ se $c^{-1}$ , respectively. Ageing was carried out at several temperatures below 8$0^{\circ}C$ using thermostatically controlled oil baths with a temperature control within$\pm$1$^{\circ}C$. It was found that the rate of strain ageing obeyed the $t^{2}$3/ law up to about five hours ageing at 6$0^{\circ}C$. The rate was slower than theses reported in case of the tensile prestrained iron. Activation energy for strain ageing has been estimated as 21.5 Kcal/mole at tile first stage of the aging process. At the second stage of ageing where the $t^{2}$3/ law is still valid, however, the activation energy was somewhat decreased. The activation energy at the first stage of ageing was about 10% larger than published results on the tensile-prestraining. This difference between the activation energies is explained in terms of the residual stress field in lattice.

• Nuclear Engineering and Technology
• /
• v.15 no.3
• /
• pp.179-187
• /
• 1983

The pH of containment spray and sump water following a LOCA for KNU 5'||'&'||'6 and KNU 1 was calculated to see if pH design criteria of containment spray system established by USNRC were met. The pH calculations have been made for the two cases; maximum pH and minimum pH. For KNU 5'||'&'||'6, results showed that long term sump pH values calculated for the maximum pH and minimum pH case well met the pH requirement of at least 8.5 and spray pH for the maximum case slightly exceeded the range of design criteria (8.5 to 11.0). For KNU 1, pH requirement of long term sump pH was also met, however, spray pH value for the maximum pH case was very largely greater than that of current pH requirement. (No pH requirement of containment spray water has been established at the time of designing KNU 1) In order to find the design parameters of containment spray system which are expected to meet the spray pH requirement, several calculations were wade, by changing the input parameters to "LCCAPH". Finally, it was shown that the boric acid concentration in RWST (refueling water storage tank), which was the primary sources of containment spray water during injection mode, be maintained the range of 2750 ppm to 2850 ppm, or tile flow rate of NaOH added to spray water he kept between 10 gpm to 24 gpm.

• Geophysics and Geophysical Exploration
• /
• v.12 no.1
• /
• pp.69-76
• /
• 2009

We report an implementation of the Ground Penetrating Radar (GPR) survey at a site that corresponds to a ruined castle. The objective of the survey was to characterise buried archaeological structures such as walls and tiles in Van Khan Tooril's Ruin, Mongolia, by 2D and 3D GPR techniques. GPR datasets were acquired in an area 10mby 9 m, with 10 cm line spacing. Two datasets were collected, using GPR with 500MHz and 800MHz frequency antennas. In this paper, we report the use of instantaneous parameters to detect archaeological targets such as tile, brick, and masonry by polarimetric GPR. Radar polarimetry is an advanced technology for extraction of target scattering characteristics. It gives us much more information about the size, shape, orientation, and surface condition of radar targets. We focused our interpretation on the strongest reflections. The image is enhanced by the use of instantaneous parameters. Judging by the shape and the width of the reflections, it is clear that moderate to high intensity response in instantaneous amplitude corresponds to brick and tiles. The instantaneous phase map gave information about the location of the targets, which appeared as discontinuities in the signal. In order to increase our ability to interpret these archaeological targets, we compared the GPR datasets acquired in two orthogonal survey directions. A good correlation is observed for the alignments of reflections when we compare the two datasets. However, more reflections appear in the north-south survey direction than in the west-east direction. This is due to the electric field orientation, which is in the horizontal plane for north-south survey directions and the horizontally polarised component of the backscattered high energy is recorded.

• Food Science and Preservation
• /
• v.8 no.4
• /
• pp.405-411
• /
• 2001

This study was conducted to investigate the effect of rice powder m tile enzyme (protease, $\alpha$-amylase, $\beta$-amylase and glucoamylase) activities of soybean meju fermented by Monascus prepureus and Monascus pilosus. The activities of the enzyme in the rice meju and the soybean meju fermented by M. pilosus were higher than those by M. perpureus. Protease activity of powdered rice meju was higher than that of granular rice meju, while $\alpha$-amylase, $\beta$-amylase and glucoamylase activities were higher in granular rice meju. Protease activity in soybean meju fermented by adding of the cultured medium of Monascus strains(CMM) as a seed inocula were higher than those of the rice powder meju, while $\alpha$-amyulase, $\beta$-amylase and glucoamylase activiities were lower than those of soybean meju by CMM. The concentration of rice powder to show maximum protease activity in soybean meju was also 10% against steamed soybean. But $\alpha$-amylase activity of soybean medju by the CMM added 2% powdered rice showed lower but the activity increaed with an increase in powdered rice, whereas $\beta$-amylase and glucoamylase activiities decreased with an increase in powdered rice. Protease activity of soybean meju fermented by 10% rice meju fermented by M. pilo년 as a seed inocula was higher than that of the meju fermented by Aspergillus oryzae, whereas $\beta$-amylase and glucoamylase activities of the soybean meju showed less than 50%.

• Nuclear Engineering and Technology
• /
• v.6 no.1
• /
• pp.14-22
• /
• 1974

Effects of anodization voltage on frequency characteristics of anodic oxide films on tantalum were analyzed based on the following impedance equatious : (equation omitted) Here $R_{f}$, $C_{f}$ and tan $\delta$$_{f}$ are equivalent series resistance in ohm, equivalent Belies capacitance in farad and dielectric loss, of anodic oxide films respectively Parameters P, $\tau$$_{ο}$, $\tau$$_{\omega}$, and Co are defined as follows: P=(d-w)/w, $\tau$$_{ο}$=$textsc{k}$$\rho$$_{ο}$, $\tau$$_{\omega}$=$textsc{k}$$\rho$$_{\omega}$, $C_{ο}$=$textsc{k}$A/d where d is the thickness of oxide film, $\omega$ is the diffusion layer thickness. $\rho$$_{ο}$ is the resistivity of oxide film at the interface of metal and the oxide, $\rho$$_{\omega}$ is the resistivity of oxide film at intrinsic region and A is the area of the film and $textsc{k}$=0.0885$\times$10$^{-12}$ $\times$dielectric constant, (in farad/cm). It was shown that dielectric loss and frequency dependence of equivalent series capacitance decrease as anodization voltage increases. This is a consequence of the fact that the thickness of diffusion layer increases a little with increasing anodization voltage whereas the total oxide thickness is proportional to the anodization voltage. The ngative deviation of measured values from tile relation, tan $\delta$$_{f}$=0.682 $\Delta$ $C_{f}$, was also discussed based on the Impedance equations given above. Here $\Delta$ $C_{f}$ is the change in capacitance between 0.1 and 1 KHZ.KHZ.Z.

• Korean Journal of Acupuncture
• /
• v.22 no.3
• /
• pp.83-104
• /
• 2005

Objectives : DaeBangPungTang(DBPT) is one of the prescriptions used for the treatment of knee arthritis in oriental medicine. The present study aimed to examine the analgesic effect of DBPT on a rat model of carrageenan-induced arthritis, and the relations between DBPT-induced analgesia and endogenous nitric oxide(NO) and inducible NO synthase (iNOS), cyclooxygenase-2 (COX-2), and c-Fos protein expression in the spinal cord. Methods : Carrageenan-induced arthritis rat model was used to test the effect of DBPT as a chronic pain model. After the induction of arthritis, rats subsequently showed a reduced stepping force of the affected limb for at least tile next 4 days. The reduced stepping force of the limb was presumably due to a painful knee, since oral infection of indomethacin produced temporary improvement of weight bearing. DBPT dissolved in normal saline was minted several acupoints. After the treatment, behavioral tests measuring stepping force were periodically conducted during the next 12 hours. Results : DBPT produced significant improvement of stepping force of the hindlimb affected by the arthritis lasting at least 9 hours. The magnitude of this improvement was equivalent to that obtained after an oral injection of 3mg/kg of indomethacin and this improvement of stepping force was interpreted as an analgesic effect. DBPT produced the improvement of stepping force of the affected hindlimb in a dose-dependent manner. Both NO production and iNOS, COX-2 protein expression increased by arthritis were suppressed by DBPT. DBPT on combination with electroacupuncture (EA) produced more powerful and longer lasting improvement of stepping force of the hindlimb affected by the arthritis than either DBPT or EA did. Conclusion : The present study suggest that DBPT produces a potent analgesic effect on the chronic hee arthritis pain model in the rat and that DBPT-induced analgesia modulate endogenous NO through the suppression of iNOS/COX-2 protein expression.

• Land and Housing Review
• /
• v.4 no.4
• /
• pp.425-434
• /
• 2013

The Small and Medium Business Administration specified 123 construction materials mandatory to purchase directly and forced the public owners to provide the contractors with materials as required by related law. This study extensively reviewed various characteristics and management factors of the owner-providing materials consumed in the public apartment housing under Direct Buying System(DBS) from the public owner's perspective. Subsequently, the major managed materials were identified, and the proper response plan was developed along the material procurement process. The Procurement Management Load Indices (PMLI) of 43 materials were evaluated according to rating criteria with procurement path, project-specified level, user requirement level, supplier's responsibility, on-site work requirement, additional parts, and inspection standards. The tile and aluminum windows were classified in the group needing high-level procurement efforts to reduce the errors and ensure the efficiency. The accurate quantity estimation method, definite purchase details, management activity definition before and after production, additional quantity for rework, interference coordination were defined as the essential activities for effectively responding to DBS.

• 한국문화재보존과학회:학술대회논문집
• /
• 2004.10a
• /
• pp.15-24
• /
• 2004

The Seokgatap pagoda composed of mainly alkali granite and other minor pink-feldspar granite, fine-grained granite, granodiorite, diorite, gabbro, and tuff. Despite the small loss and damage derived from joints, its peel-off and exfoliation are serious enough to cause the heavy deterioration on the stone surface. The chemical and petrological weathering has partly replaced the original rock-forming minerals with clay minerals and iron oxyhydroxides. Based on the petrogenesis, rock materials of the pagoda is very similar to rocks of Dabotap pagoda and the Namsan granite in the Gyeongju. The central fart of the pagoda has sunken highly, which caused all the corners to split and the structural transformation to become worse. The reverse V-shaped gaps between the materials have broken stones filled in a coarse way. The iron plates inserted between the upper flat stone laid on other stones and tile pagoda body in the north and east side has been exposed in the air and corroded, discoloring of the adjacent stones. The overall diagnosis of the Seokgatap pagoda is the deteriorated functions of the stone materials, which calls for a long-term monitoring and plans to reinforce the stone surfaces. But the main body including the pagoda roof stone needs washing on a regular basis, and the many different cracks should be fixed with glue by using the fillers or hardeners designed for stone cultural properties after removing the cement mortar. In case of the replacement of the stone materials with new stones, it's necessary to examine the pagoda for the center of gravity and support intensity of the materials. The structural stability of the pagoda can be attained by taking a reinforce measure in geotechnical engineering and making a drainage. The ground humidity, which has aggravated weathering and structural instability, should be resolved by setting up a humidity reduction facility. The contamination of lichens and bryophyte around the pagoda and on the surface is serious. Thus biochemical treatments should be given too in order to prevent further biological damages and remove the vegetation growing on the discontinuous planes.

• 한국문화재보존과학회:학술대회논문집
• /
• 2004.10a
• /
• pp.81-91
• /
• 2004

The host rock of standing sculptured Buddha in the Yongamsa temple was macular biotite granite, which has gone through mechanical and chemical weathering. The principal rock-forming minerals are quartz, plagioclase, alkali feldspar, and biotite, the last two of which have been transformed into clay minerals and chlorite due to weathering processes. The bed rock around the Buddha statue is busily scattered with steep inclinations that are almost vertical and discontinuous planes with the strikes of $N8^{\circ}E$. The major joints have the strikes of N4 to $52^{\circ}W$ and N6 to $88^{\circ}E$ and the dips of 42 to $89^{\circ}$. Especially thee development of the joints that cross the major joints causes tile structural instability of the rock. The host rock of the Buddha image is separated into many different rock masses because of the also many different discontinuity, which group accounts for about $12{\%}$ of the rock. Thus it's estimated that the bed rock has not only plane and toppling failure but also wedge failure in all the sides. Since the earth pressure and the inclination pressure are imposed on the body of the Buddha in the basement rock, it's urgent to give a treatment of geotechnical engineering for the sake of its structural stability. The parts where serious fractures are seen should receive the hardening process using the fillers for stones. It's also necessary to introduce a landfill liner system in order to reduce the ground humidity. The rock surface of the Buddha statue are partly contaminated by lichens and bryophyte. The joints have turned into earth, which promotes the growth of weeds and plant roots. Thus biochemical treatments should also be considered to get rid of the vegetation along the discontinuous planes and prevent further biological damages.