• 한국재난정보학회 논문집
• /
• 제16권3호
• /
• pp.449-457
• /
• 2020

연구목적:서울시는 공동관리 등급 기준에 따라 공동의 규모, 아스팔트포장 두께, 포장면의 균열깊이를 고려하여 긴급, 우선, 일반, 관찰등급으로 공동의 위험도를 분류하고 있다. 본 연구에서는 2019년 서울시 공동조사용역에서 발견된 265개소의 공동의 상부 포장상태를 확인하여 포장균열이 확인된 17개소에 대하여 균열깊이를 측정하였다. 연구방법: 1차에서는 확인된 공동의 균열 확인을 위하여 버니어 캘리퍼스, 테이퍼 게이지, 깊이 게이지를 활용하여 균열 폭 및 깊이를 측정하였다. 2차에서는 상부 노면에서 가장 크게 균열이 발생한 위치를 확인하여 아스콘을 천공 후 균열 깊이를 추가로 측정하였다. 연구결과:확인된 시험공동 17개소 중 9개소에서 공동 관리 등급이 상향 조정되었다. 따라서, 긴급복구와 우선복구의 경우에는 포장 균열 깊이와 잔여 아스팔트 콘크리트 포장 두께에 따라 등급 조정이 필요하다. 결론:공동 상부에 균열이 발생한 경우는 천공을 통하여 균열 진행 상태를 파악하고 잔여 아스팔트 콘크리트 두께를 확인하여 공동등급을 결정해야한다.

• 대한기계학회논문집A
• /
• 제27권2호
• /
• pp.239-246
• /
• 2003

This paper proposes engineering estimation equations of elastic-plastic J and COD fur axial through-wall cracked pipes under internal pressure. Based on detailed 3-D FE results based on deformation plasticity, the plastic influence functions for fully plastic J and COD solutions are tabulated as a function of the mean radius-to-thickness ratio, the normalized crack length. and the strain hardening. Based on these results, the GE/EPRI-type J and COD estimation equations are proposed and validated against the 3-D FE results based on deformation plasticity. For more general application to general stress-strain laws or to complex loading, the developed GE/EPRI-type solutions are re-formulated based on the reference stress concept. Such a reformulation provides simpler equations for J and COD, which are then further extended to combined internal pressure and bending. The proposed reference stress based J and COD estimation equations are compared with elastic-plastic 3-D FE results using actual stress-strain data for Type 316 stainless steels. The FE results for both internal pressure cases and combined internal pressure and bending cases compare very well with the proposed J and COD estimations.

• Nuclear Engineering and Technology
• /
• 제54권6호
• /
• pp.2188-2197
• /
• 2022

To ensure the safety margin of a reactor pressure vessel (RPV) under normal operating conditions, it is regulated through the pressure-temperature (P-T) limit curve. The stress intensity factor (SIF) obtained by the internal pressure and thermal load should be obtained through crack analysis of the nozzle corner crack in advance to generate the P-T limit curve for the nozzle. In the ASME code Section XI, Appendix G, the SIF via the internal pressure for the nozzle corner crack is expressed as a function of the cooling or heating rate, and the wall thickness, however, the SIF via the thermal load is presented as a polynomial format based on the stress linearization analysis results. Inevitably, the SIF can only be obtained through finite element (FE) analysis. In this paper, simple prediction equations of the SIF via the thermal load under, cool-down and heat-up conditions are presented. For the Korean standard nuclear power plant, three geometric variables were set and 72 cases of RPV models were made, and then the heat transfer analysis and thermal stress analysis were performed sequentially. Based on the FE results, simple engineering solutions predicting the value of thermal SIF under cool-down and heat-up conditions are suggested.

• 수산해양기술연구
• /
• 제20권1호
• /
• pp.30-36
• /
• 1984

대규모의 소성역을 동반하면서 파괴하는 고인성 재료의 탄소성 파괴 반가를 위하여 제안된 바 있는 CPE 모형의 유효성을 입증하고자 소성역의 영향을 보정한 선형 파괴역학과의 이론적 검토와 오오스테나이트계 스테인레스강에 대한 실험적 비교검토를 통하여 얻은 결론은 다음과 같다. 예측한 바와 같이 선형 파괴역학의 적용은 소규모 항복조건이 성립하는 경우에만 가능하며 CPE 모형은 대변형을 형성하면서 파괴하는 경우의 파괴모형으로서 유효하다. 더욱 엄밀한 유효성을 입증하기 위하여 다음의 사항이 필요하다고 본다. 1. 크랙의 길이가 짧은 시험편에 대한 실험이 필요하다. 2. 크랙성장 개시점을 정확하게 찾을 수 있는 방법이 필요하다. 3. 파괴 진행영역에 대한 두께의 영향을 고려해 보아야 할 필요성이 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1673-1678
• /
• 2007

The use of flip-chip type electronic package offers numerous advantages such as reduced thickness, improved environmental compatibility, and downed cost. Despite numerous benefits, flip-chip type packages bare several reliability problems. The most critical issue among them is their electrical performance deterioration upon consecutive thermal cycles attributed to gradual delamination growth through chip and adhesive film interface induced by CTE mismatch driven shear and peel stresses. The electronic package in use is heated continuously by itself. When the crack at a weak site of the electronic package occurs, thermal deformationon the chip side is changed. Therefore, we can measure these micro deformations by using Moire interferometry and find out the crack length.

• 한국안전학회지
• /
• 제15권2호
• /
• pp.46-50
• /
• 2000

A theoretical model for the evaluation of small surface fatigue crack initiated from a pit-type surface flaw is presented. The low frequency scattering model is developed based on the reciprocity principle for the elastic wave scattering. The effect of the flaw on the surface wave reflection from the crack is taken into account approximately by means of the stress intensity factor of cracks on a through thickness hole. The reflection coefficient of surface wave is derived for the prediction of small surface crack depth. Calculated results for pits with different sizes are illustrated.

• Journal of Welding and Joining
• /
• 제21권1호
• /
• pp.72-79
• /
• 2003

Fatigue behaviour of partially penetrated butt-welded joints in high strength steel plates, in which crack-like structural defect, i.e. lack of penetration(LOP), is inevitably introduced during welding processes, was investigated. Fatigue lives of two types of welded joints, namely X-grooved and K-grooved joints, were experimentally determined first. Observed fatigue crack propagation behaviours of the partially penetrated butt-welds were interpreted through considering 3-dimensional semi-elliptical crack shape in front of the LOP. Based on such interpretation, a fracture mechanical method to estimate stress intensity factors at the crack tip was proposed. Since the fatigue lift of the partially penetrated butt-welds was strongly influenced by the ratio of size of the LOP to thickness, D/t, the D/t was used as a main parameter to calculate the fatigue lift by using the proposed method. Comparison of the fatigue lift obtained experimentally and analytically agreed well with each other. Hence it is suggested that the method used in this work to predict fatigue lift of the partially penetrated butt-welds can be applied to real cases with improved lift-prediction capability.

• 소성∙가공
• /
• 제16권1호
• /
• pp.3-8
• /
• 2007

Novel compression molding system for preform has been developed in this study. The preforms for injection blow molding and injection stretch blow molding are being manufactured by injection molding. However it contains gate mark that affects the bottom crack in the PET bottle. The compression molded preform does not contain gate mark, thus the appearance quality of bottle has been increased and the residual stress near gate(bottom of the bottle) has been reduced. The thickness distributions, haze, and transmittance are well accepted for the preform. Also, flow characteristics of the resin between a core and cavity could be analyzed through computer simulation.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.330-331
• /
• 2006

Fabrication of a nano-laminar ceramic composite by sintering thin ceramic plates was examined. Silver-coated glass flakes with a thickness of less than $1{\mu}m$ were consolidated by pulsed current sintering or hotpressing to obtain model composites. The samples sintered at the optimum conditions were fairly dense, and the flakes were aligned by uniaxial press. The metal coating remained on the flakes through the sintering process, and became an interface layer between the flakes. No crack propagation through the transverse direction of the lamellar was observed in the indentation test. The possibilities of high resistance against crack propagation was suggested.

• 대한기계학회논문집A
• /
• 제30권4호
• /
• pp.420-427
• /
• 2006

The structural and leakage integrity of steam generator tubes should be sustained against all postulated loads even if a crack is present. During the past three decades, most of the efforts with respect to integrity evaluation of steam generator tubes have been focused on limit load solutions but, recently, the applicability of elastic-plastic fracture mechanics was examined cautiously due to its effectiveness. The purpose of this paper is to introduce a testing method to estimate fracture resistance characteristics of steam generator tubes with a through-wall crack. Due to limited thickness and diameter, inevitably, the steam generator tubes themselves were tested instead of standard specimen or alternative ones. Also, a series of three dimensional elastic-plastic finite element analyses were carried out to derive closed-form estimation equations with respect to J-integral and crack extension for direct current potential drop method. Since the effectiveness of $J_{IC}$ as well as J-R curves was proven through comparison with those of standard specimens taken from pipes, it is believed that the proposed scheme can be utilized as an efficient tool for integrity evaluation of cracked steam generator tubes.