• Environmental Analysis Health and Toxicology
• /
• v.5 no.3_4
• /
• pp.19-28
• /
• 1990

Nitroarenes are ubiquitous environmental pollutants displaying potent mutagenicity in bacteria and carcinogenicity in mammal. In this study, the concentration of nitroarenes in coarse and fine particles and mutagenicity of POC$\_$N/ fraction was investigated in suspended particulates at the Shinchon and Bulkwang area of Seoul. The suspended particulates were collected bimonthly by a high volume cascade impactor air sampler from July 1987 to May 1988. Extractable organic matter was obtained by ultrasonic extraction on diethly ether/cyclohexane (8/2, v/v). Neutral fraction was obtained by liquid-liquid extraction. Polar neutral organic compounds (POC$\_$N/) was fractionated by thin-layer chromatography. Finally, the concentrations of nitroarenes in POC$\_$N/ fraction were measured and determined by capillary gas chromatography. Direct and indirect mutagenicity of POC$\_$N/ fraction were measured using Salmonella typhimurium TA 98. The result were as follows: 1) Major nitroarenes at the Shinchon area was 1-nitropyrene and at the Bulkwang area it was 2,7-dinitro-9-fluorenone during the year. 2) Average concentration of total nitroarenes measured was 67.26 ng/m$^3$in fine particles which was 1,3 folds higher that in coarse particle (52.30 ng/m$^3$). 3) Annual pattern of nitroarenes concentrations revealed that concentration during heating season (Feb., Jan., Mar.) was 2.2 folds higher than that in non heating season (May, Jul., Sep.). Concentration of each season has 157.68 ng/m$^3$and 80.39 ng/m$^3$. 4) The mutagenic activity of POC$\_$N/ fraction from fine particles was higher compared to that of coarse particles and was increased when metabolically activated, with 59 mixture. Mutagenicities, Metabolically activated, were significantly different between Shinchon and Bulkwang area, 322.8 rev/250 $\mu\textrm{g}$/plate and 286.8 rev/250 $\mu\textrm{g}$/plate, respectively. 5) Annual pattern of mutagenicity of POC$\_$N/ fraction revealed that mutagenicity during the heating season was 1.7 folds higher at Shinchon area and 1.2 folds higher at Bulkwang than during the non heating season. The variable contents and levels of nitroarenes in suspended particulates may affect human health significantly. Further studies such as risk assessment should be conducted on the basis of these kind of studies.

• Advances in Traditional Medicine
• /
• v.10 no.1
• /
• pp.21-28
• /
• 2010

The objective of the present investigation is to evaluate the antimicrobial potency of the terpenoid fractions isolated from Luffa cylindrica seeds against various pathogenic microbes. The seeds were powdered and extracted with methanol in soxhlet appratus based on phytochemical screening. Three terpenoid components were isolated by column chromatography and identified by thin layer chromatography and chemical analysis which were designated as ${LCSF_4}^*$, ${LCSF_6}^*$ & ${LCSF_8}^*$ respectively. Disc diffusion method was employed to determine the antimicrobial effectiveness of test compounds I, II and III $({LCSF_4}^*,\;{LCSF_6}^*\;&\;{LCSF_8}^*)$ against 6 microbial species viz., Staphylococcus (S.) aureus, Bacillus (B.) subtilis, Escherichia (E.) coli, Pseudomonas (P.) aeruginosa, Candida (C.) albicans and Aspergillus niger. The disc was saturated with $100{\mu}l$ of each compound, allowed to dry and introduced on the upper layer of seeded agar plate. The plates were incubated overnight at $37^{\circ}C$. Microbial growth was determined by measuring the zonal inhibition diameters. Compound I showed maximum potency against gram positive S. aureus (21 mm) in comparison with standard ciprofloxacin (38 mm), whereas the same compound was completely devoid of activity against both the fungi tested. Compound II was found to be highly sensitive against both the gram negative E. coli (20 mm) and P. aeruginosa (22 mm). Compound II was found to exhibit maximum potency against the fungi C. albicans (15 mm) and A. niger (20 mm). Compound III was found to be very effective against both the gram positive S. aureus (20 mm) and B. subtilis (15 mm) respectively.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.1
• /
• pp.127-133
• /
• 2016

This study is performed that furniture and interior materials of MDF's (Medium Density Fiberboard) biodegradation properties, and the goal of this study is investigation of possibility of waste-MDF's composting after landfilling. To investigate biodegradation, this study was performed according to KS M ISO 14855-1, and there were two different soil conditions including a compost condition and an activated vermiculite condition as artificial soil. This experiment was tested for 40 days. The measurement of carbon-dioxide generation was processed every 24 hour in 1-2 week, and every 48 hour after 3 week. In the same days, MDF showed 24.4% of biodegradation in compost condition, and 6.2% in activated vermiculite. Also, the reference material of TLC (thin-layer chromatography) grade cellulose showed 26.4%, 11.4% in compost and activated vermiculite respectively. The dilution plate method was performed for biological analysis in the study. This experiment was used for investigation of inoculum's (Bacillus licheniformis) activity. As the result of bioassay, compost has more other germs include inoculum than activated vermiculite in the first week. Especially in the 2nd week, the reference material under the compost condition showed the most germ's activity, and also the biodegradation was the highest. Consequentially, compost condition was able to reduce a performing period of biodegradation testing than activated vermiculite. However, activated vermiculite could be stabilizing errors between repetition.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.365-372
• /
• 2004

The laser welding and its analysis were carried out using high power 6kW $CO_2$ laser for high strength steels such as DP, TRIP and conventional high strength steels. Bead on plate welding of thin sheet was examined to investigate the effect of weld variables of laser welding, and to obtain optimum welding condition. In order to investigate the formability of welded high strength steels, LDH test was added on this work. At high welding speed, the partial penetration was obtained by low heat input. Meanwhile, porosity was formed in the bead at low weld speed because of extremely higher heat input. The optimum welding condition of welding was derived from bead width, penetration and hardness property. It was shown that the DP steels had lower porosity level and smooth bead shape, therefore better laser weldability than TRIP steels and conventional high strength steels. In addition, LDH test shows that the welded DP steels have about $90\%$ formability value of base metal, although TRIP steel and conventional high strength steels have about $80\%$ formability value of its base metal.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.5
• /
• pp.60-69
• /
• 2016

This paper presents a numerical investigation on kerosene-air mixture detonation and behaviors of thermal elasto-plstic thin metal tube under detonation loading based on multi-material analysis. The detonation loading is modeled by the kerosene-air mixture detonation which is compared with Chapman-Jouguet (C-J) condition and experimental cell size. To conform the elasto-plastic model, plastic and elastic behaviors are verified by Taylor impact and plate bending motion, respectively. The numerical results are compared with the theory on burst pressure of tube. The critical deformable thickness with the thermal softening considered is good agreement with the theoretical value.

• Journal of the Korea Society of Computer and Information
• /
• v.10 no.2 s.34
• /
• pp.39-47
• /
• 2005

This paper proposes and analyzes the MAC(Message Authentication Code) algorithm that is used for the transition integrity and the entity authentication of message. The MAC algorithm uses the DES algorithm which has 64-bit block and 56-bit key and we compare the security according to 64-bit and 32-bit length of MAC value. Moreover, we use the SEED algorithm which has 128-bit block and 128-bit key and compare the security according to 128-bit and 64-bit length of MAC value. We analyze the security the forgery attack according to length of message and length of MAC value. this paper, a coarse-to-fine optical flow detection method is proposed. Provided that optical flow gives reliable approximation to two-dimensional image motion, it can be used to recover the three-dimensional motion. but usually to get the reliable optical flows are difficult. The proposed algorithm uses Horn's algorithm (or detecting initial optical flow, then Thin Plate Spline is introduced to warp a image frame of the initial optical flow to the next image frame. The optical flow for the warped image frame is again used iteratively until the mean square error between two image sequence frames is lowered. The proposed method is experimented for the real moving Picture image sequence. The proposed algorithm gives dense optical flow vectors.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.2
• /
• pp.97-108
• /
• 2015

In the design of sailing yachts, para-glider, or high-sky wind power, etc., the analysis of side-wind aerodynamic forces exerted on a cambered 3-D model is very important to predict the performance of various machinery systems. To understand the essential flow physics around the three-dimensional shape, simplified rigid-body models are proposed in this study. Four parameters such as free stream velocity, angle of attack, aspect ratio, and camber are considered as the independent variables. Lift and drag coefficients are computed with CFD technique using ANSYS-CFX, and the results with the visualization of post-processed flow fields are analyzed in the viewpoint of fluid dynamics.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.4 s.97
• /
• pp.57-63
• /
• 1999

A thin metal plate such as detent spring has the shape deformation due to the phenomenon of spring back after press machining and heat treatment process. This requires the correction of spring shape and force in final inspection process. To do correction of the shape deformation the impact force is manually applied to the bended part of detent spring after measuring the shape deformation and spring force. To develop the automatic spring force correction system, applied force of occurring plastic deformation must be derived from the experimental method. But frequent change of spring shape and material makes it difficult to accomplish the experimental method to be applied. This paper describes the analytical method for detent spring force correction system is to be substituted for the experimental method. FEM(Finite Element Method) is used to find the boundary value between elastic and plastic deformation in the analytical method. To confirm the validity of the analytical method, the result of two methods is compared each other at various applied force conditions. It shows that the simulation result of the analytical method is consistent with the result of the experimental method within the error bound ${\pm}$5%. The result of this paper is useful for development of the automatic spring correction system and reduction of the complicated and tedious processes involved in experimental method.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.1
• /
• pp.24-38
• /
• 1989

In this study, an attempt for formulating a new and simplified rectangular finite element having only four corner nodal points is made to analyze the elastic-plastic large deformation behaviour up to the ultimate limit state of plates with initial imperfections. The present finite element contains the geometric nonlinearity caused by both in-plane and out-of-plane large deformation because for very thin plates the influence of the former may not be negligible. Treatment of expanded plastic zone in the plate thickness direction of the element is simplified based upon the concept of plastic node method so that the elastic-plastic stiffness matrix of the element is derived by the simple matrix operation without performing complicated numerical integration. Thus, a considerable saving of the computational efforts is expected. A computer program is also completed based on the present formulation and numerical calculation for some examples is performed so as to verify the accuracy and validity of the program.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.271-275
• /
• 2010

Forming tool design is carried out for a manufacturing a outer shell structure of the nozzle extension of regenerative cooling thrust chamber. The method which manufactures outer shell structure of nozzle extension is a metal forming process using thin plate. Because the configuration of outer shell structure is changed after forming process by springback effect, the outer shell structure can't be exactly formed with the same forming tool as configuration of the nozzle extension. Therefore forming tool design considering springback effect is necessary for manufacturing the outer shell structure of the nozzle extension. In this study, new designed forming tool configuration was generated to decrease the errors between nozzle contour and formed structure. The analysis results show that the errors between nozzle contour and formed structure is significantly decreased using the new designed forming tool.