• 한국진공학회지
• /
• 제18권3호
• /
• pp.213-220
• /
• 2009

Al이 도핑된 투명 전도성 Al:ZnO (AZO) 박막에 대한 RF magnetron sputtering 증착 법을 이용한 저온 최적공정조건을 연구하였다. 투명전극 재료로써의 AZO 박막의 전기적, 결정학적 물성을 최대한 향상시키기 위해서, in-situ상태에서 유리기판상에 최적화된 증착 조건의 AZO 버퍼 층을 삽입하는 이중박막 구조를 제작하였다. RF 인가 전력 $50{\sim}60\;W$에서 증착된 버퍼층 위에 120 W의 RF 전력에서 성장한 AZO 박막의 경우, 비저항 $3.9{\times}10^{-4}{\Omega}cm$, 전하 캐리어농도 $1.22{\times}10^{21}/cm^3$, 홀 이동도 $9.9\;cm^2/Vs$의 전기적 특성을 보였다. 이러한 결과는 버퍼 층이 없는 기존의 단일 구조와 비슷하나, 전기적 비저항 특성을 약 30% 정도 향상시킬 수 있었으며, 전기적 특성의 향상 원인을 $Ar^+$ 이온의 입사 에너지의 변화에 따른 버퍼 층의 압축응력과 결정화 정도와의 의존성으로 설명하였다.

• 한국결정성장학회지
• /
• 제30권1호
• /
• pp.1-6
• /
• 2020

본 연구에서는 패턴화된 사파이어 기판 위에 HVPE(Hydride Vapor Phase Epitaxy System) 법에 의해 50 nm 두께의 AlN thin film을 증착한 뒤, 에피층 구조가 MO CVD에서 성장되었다. AlN 버퍼층 박막의 표면형상이 SEM, AFM에 의해서, 에피층 구조의 GaN 박막의 결정성은 X-선 rocking curve에 의해 분석되었다. 패턴화된 사파이어 기판 위에 증착된 GaN 박막은, 사파이어 기판 위에 증착된 GaN 박막의 경우보다 XRD 피크 세기가 다소 높은 결과를 나타냈다. AFM 표면 형상에서 사파이어 기판 위에 AlN 박막이 증착된 경우, GaN 에피층 박막의 p-side 쪽의 v-pit 밀도가 상대적으로 낮았으며, 결함밀도가 낮게 관찰되었다. 또한, AlN 버퍼층이 증착된 에피층 구조는 AlN 박막이 없는 에피층의 광출력에 비해 높은 값을 나타냈다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.273-273
• /
• 2008

This paper describes the frequency response of two-port surface acoustic wave (SAW) resonator made of 002-polycrystalline aluminum nitride (AlN) thin film on 111-poly 3C-SiC buffer layer. In there, Polycrystalline AlN thin films were deposited on polycrystalline 3C-SiC buffer layer by pulsed reactive magnetron sputtering system, the polycrystalline 3C-SiC was grown on $SiO_2$/Si sample by CVD. The obtained results such as the temperature coefficient of frequency (TCF) of the device is about from 15.9 to 18.5 ppm/$^{\circ}C$, the change in resonance frequency is approximately linear (30-$150^{\circ}C$), which resonance frequency of AlN/3C-SiC structure has high temperature stability. The characteristics of AlN thin films grown on 3C-SiC buffer layer are also evaluated by using the XRD, and AFM images.

• 한국분말재료학회지
• /
• 제13권1호
• /
• pp.62-67
• /
• 2006

Friction welding of $Al_2O_3$ particulate reinforced aluminum composites was performed and the following conclusions were drawn from the study of interfacial bonding characteristics and the relationship between experimental parameters of friction welding and interfacial bond strength. Highest bonded joint efficiency (HBJE) approaching $100\%$ was obtained from the post-brake timing, indicating that the bonding strength of the joint is close to that of the base material. For the pre-brake timing, HBJE was $65\%$. Most region of the bonded interface obtained from post-brake timing exhibited similar microstructure with the matrix or with very thin, fine-grained $Al_2O_3$ layer. This was attributed to the fact that the fine-grained $Al_2O_3$ layer forming at the bonding interface was drawn out circumferentially in this process. Joint efficiency of post-brake timing was always higher than that of pre-brake timing regardless of rotation speed employed. In order to guarantee the performance of friction welded joint similar to the efficiency of matrix, it is necessary to push out the fine-grained $Al_2O_3$ layer forming at the bonding interface circumferentially. As a result, microstructure of the bonded joint similar to that of the matrix with very thin, fine-grained $Al_2O_3$ layer can be obtained.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.465-465
• /
• 2012

In this study, we developed an Al2O3 nanolaminated single gas barrier layer using a Neutral Beam Assisted Sputtering (NBAS) process. The NBAS process can continuously change crystalline structures from an amorphous phase to a nanocrystal phase with various grain sizes and lead to the formation of a nanolaminated structure in the single inorganic thin film. As a result, the water vapor transmission rates (WVTR) of the nanolaminated Al2O3 thin films by NBAS process have improved more than 40% compared with that of conventional Al2O3 layers by the RF magnetron sputtering process under the same sputtering conditions.

• 한국재료학회지
• /
• 제17권8호
• /
• pp.447-451
• /
• 2007

We investigated the dependence of the various annealing conditions and thickness ($6\sim45nm$) of the Ti-doped $Al_2O_3$ coating on the electrochemical properties and the capacity fading of Ti-doped $Al_2O_3$ coated $LiCoO_2$ films. The Ti-doped-$Al_2O_3$-coating layer and the cathode films were deposited on $Al_2O_3$ plate substrates by RF-magnetron sputter. Microstructural and electrochemical properties of Ti-doped-$Al_2O_3$-coated $LiCoO_2$ films were investigated by transmission electron microscopy (TEM) and a dc four-point probe method, respectively. The cycling performance of Ti-doped $Al_2O_3$ coated $LiCoO_2$ film was improved at higher cut-off voltage. But it has different electrochemical properties with various annealing conditions. They were related on the microstructure, surface morphology and the interface condition. Suppression of Li-ion migration is dominant at the coating thickness >24.nm during charge/discharge processes. It is due to the electrochemically passive nature of the Ti-doped $Al_2O_3$ films. The sample be made up of Ti-doped $Al_2O_3$ coated on annealed $LiCoO_2$ film with additional annealing at $400^{\circ}C$ had good adhesion between coating layer and cathode films. This sample showed the best capacity retention of $\sim92%$ with a charge cut off of 4.5 V after 50 cycles. The Ti-doped $Al_2O_3$ film was an amorphous phase and it has a higher electrical conductivity than that of the $Al_2O_3$ film. Therefore, the Ti-doped $Al_2O_3$ coated improved the cycle performance and the capacity retention at high voltage (4.5 V) of $LiCoO_2$ films.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1096_1097
• /
• 2009

Aluminium doped zinc oxide(ZnO:Al) thin film, which is mainly used as a transparent conducting electrode in electronic devices, has many advantages compared with conventional indium tin oxide(ITO). In this paper in order to investigate the possible application of ZnO:Al thin films as a transparent conducting electrode for flexible film-typed dye sensitized solar cell (FT-DSCs), ZnO:Al and ITO thin films were prepared on the polyethylene terephthalate (PET) substrate by r. f. magnetron sputtering method. Specially one-inched FT-DSCs using either a ZnO:Al or ITO electrode were also fabricated separately under the same manufacturing conditions. Some properties of both the FT-DSCs with ZnO:Al and ITO transparent electrodes, such as conversion efficiency, fill factor, and photocurrent were measured and compared with each other. The results showed that by doping the ZnO target with 2 wt% of $Al_2O_3$, the film deposited at discharge power of 200W resulted in the minimum resistivity of $2.2\times10^{-3}\Omega/cm$ and at ransmittance of 91.7%, which are comparable with those of commercially available ITO. Two types of FT-DSCs showed nearly the same tendency of I-V characteristics and the same value of conversion efficiencies. Efficiency of FT-DSCs using ZnO:Al electrode was around 2.6% and that of fabricated FT-DSCs using ITO was 2.5%. This means that ZnO:Al thin film can be used in FT-DSCs as a transparent conducting layer.

• 한국산학기술학회논문지
• /
• 제7권5호
• /
• pp.801-804
• /
• 2006

[ $YBa_2Cu_3O_{7-{\delta}}(YBCO)$ ]계 초전도 선재용 $GdAlO_3(GAO)$ 버퍼층을 졸-겔(sol-gel) 공정에 의해 제조하였다. 전구체 용액은 Gd 질산염과 Al 질산염을 1:1 화학양론비로 하여 메탄올에 용해하여 준비하였다. 전구체 용액을 $SrTiO_3(STO)$ (100) 단결정 기판위에 스핀 코팅하고, 수분이 포함된 $N_2-5%\; H_2$ 분위기에서 $1000^{\circ}C$에서 2시간 열처리 하였다. 열처리 후 GAO 층의 표면에 대한 주사전자현미경 관찰에 의해 GAO 층이 에피택셜의 특징인 각면 형상을 갖는 것을 알 수 있었다. X-선 회절분석에 의하면 GAO 버퍼층은 c-축으로 우선 배향된 에피택셜 박막으로써 반가폭이 각각 (002)면에서 $0.29^{\circ}(out-of-plane)$, {112}지면에서 $1.10^{\circ}(in-plane)$의 우수한 배향성을 나타내었다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.318-321
• /
• 2009

We have studied transparent top gate Al-Zn-Sn-O (AZTO) TFTs with an $Al_2O_3$ protective layer (PL) on an active layer. We also fabricated a transparent 2.5 inch QCIF+AMOLED display panel using the AZTO TFT back-plane. The AZTO active layers were deposited by RF magnetron sputtering at room temperature and the PL was deposited by ALD with two different processes. The mobility and subthreshold slope were superior in the cases of the vacuum annealing and the oxygen plasma PL compared to the $O_2$ annealing and the water vapor PL, however, the bias stability was excellent for the TFTs of the $O_2$ annealing and the water vapor PL.

• 한국재료학회지
• /
• 제27권6호
• /
• pp.295-300
• /
• 2017

Aluminum-oxide($Al_2O_3$) thin films were deposited by electron cyclotron resonance plasma-enhanced atomic layer deposition at room temperature using trimethylaluminum(TMA) as the Al source and $O_2$ plasma as the oxidant. In order to compare our results with those obtained using the conventional thermal ALD method, $Al_2O_3$ films were also deposited with TMA and $H_2O$ as reactants at $280^{\circ}C$. The chemical composition and microstructure of the as-deposited $Al_2O_3$ films were characterized by X-ray diffraction(XRD), X-ray photo-electric spectroscopy(XPS), atomic force microscopy(AFM) and transmission electron microscopy(TEM). Optical properties of the $Al_2O_3$ films were characterized using UV-vis and ellipsometry measurements. Electrical properties were characterized by capacitance-frequency and current-voltage measurements. Using the ECR method, a growth rate of 0.18 nm/cycle was achieved, which is much higher than the growth rate of 0.14 nm/cycle obtained using thermal ALD. Excellent dielectric and insulating properties were demonstrated for both $Al_2O_3$ films.