• Journal of Korean Society of Forest Science
• /
• v.37 no.1
• /
• pp.17-30
• /
• 1978

Press drying was used on italian poplar (Populus euamericana) to find the profitable means of drying. This study was designed to investigate the process of platen drying considering core temperature, drying time, current moisture content, drying rate, shrinkage and recovery, and green volume specific gravity, equilibrium moisture content and dimensional stability of press dried material and air dried material, The drying tests were conducted using 1.5 centimeter thick material at platen temperature of $175^{\circ}C$. The results were summarized as follows. 1. Core temperature was divided into three stages of drying characterized by period initial heating, plateau temperature and rising core temperature. Plateau temperature was 114 to $119^{\circ}C$. 2. The following predicting equations of drying time(y) in different core temperatures were developed for initial thickness($x_1$), initial moisture content ($x_2$) and final moisture content ($x_3$) 3. The predicting equaltion of current moisture content(u) was log u=4.658-0.060t as funtion of drying time(t) and that of drying rate(r) was log r=-2.797-0.049t. Current moisture content and drying rate of air drying were shown in figure 2. 4. The predicting equation of shrinkage in thickness direction(y) was log y=1.933+0.038t as function of drying time(t), and that of expansion in width direction was $y=-0.692+0.043t-0.001t^2$. 5. Thickness shrinkage was increased more than proportional at to pressure increase. Width shrinkage and thickness recovery was greatest at 35psi. 6. Green volume specific gravity of press dried material was 25% greater than that of air dried material. But equilibrium moisture content of press dried material was less 24% than that of air dried material. Antishrinkage efficiency of press dried material were obtained 27.7%.

• Journal of Welding and Joining
• /
• v.30 no.6
• /
• pp.120-125
• /
• 2012

Because ships and offshore structures have very large dimensions and complicated shapes, it is difficult to determine the deformation or internal stress in the structure by simple lab tests. Thus, a rigorous analysis by using the computer simulation technology is essential for obtaining their distortions by considering the entire production process characteristics. The rapid development of computer technology made it possible to analyze the heat transfer phenomena, deformation and phase transformation in the welded joint. For large shell structures, shell elements modeling contributed primarily to this development. But if a welding is done by multi-pass, shell elements whose thickness are unchangeable can hard to describe the local situation. Recently, it was researched how to introduce the imaginary temperature for V grooved multi-layer butt welding in strain-boundary method (a kind of shrinkage methodologies). In the present study, we formulated the imaginary temperature for the double bevel and double V groove by considering the thickness change of each pass through the bead and the thickness directions simultaneously and also demonstrated the feasibility of the formula by applying it to the thermal distortion analysis of the erection process of crane pedestal.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.285-287
• /
• 2005

During fabrication of deck house block in passenger ships, the problem of unexpected large deformation and distortion frequently occurs. In this case, line and spot heating method were widely used to correct the distortion of thin plate structure. Spot heating was especially used for the case under 5mm thickness. Few papers are available on the working conditions of spot heating method but only little information on deformation control. In this study, evaluation was carried out on the temperature distribution of spot heating methods using FEA and practical experiments for various heating time. IIn FEA, heat input model was established using Tsuji's double Gaussian heat input mode (Tsuji, I., 1988). This model was verified by comparing with experimental data. Also radial shrinkage and angular distortion due to spot heating were determined and compared with experimental results. Thermo elasto-plastic analysis was performed using commercial FE code, MSC/MARC. Radial shrinkage and angular distortion were measured using 3D measuring apparatus. Based on these results, simplified analysis model for deformation by spot heating was established.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.5
• /
• pp.496-503
• /
• 2007

Although weld-induced deformation is inevitable in shipbuilding, it is important to reduce it as low as possible during fabrication for a more efficient production of ships' blocks. The weld-induced deformation is more serious in thin plates than in thick plates because heat affect zone of thin plates is wider than that of thick plates, and in addition internal and external constraints much more influence upon weld-induced deformation of thin plates. This paper deals with the application of the mechanical tensioning method to butt weld of thin plates to reduce the transverse and longitudinal deformation. in order to investigate the quantitative effect of tensioning method upon the reduction of angular deformation and shrinkage in longitudinal and transverse direction of weld line, butt welding test have been carried out for several thin plate specimens with varying plate thickness and magnitude of tensile load. Numerical simulation has been also carried out to compare the weld-induced deformation and residual stress. From the present study, it has been found that the tensioning method is very effective on reduction of weld-induced residual stress as well as weld-induced deformation.

• Magazine of the Korea Concrete Institute
• /
• v.5 no.2
• /
• pp.181-188
• /
• 1993

In this study, a numerical method for the material nonlinear analysis of reinforced concrete shell structures including the time dependent effects due to creep and shrinkage is developed. Degenerate shell elements with the layered approach are used. The perfect or strain hardening plasticity model in compression and the linearly elastic model in tension until cracking for concrete are employed. The reinforcing bars are considered as a steel layer of equivalent thickness. Each :steel layer has an uniaxial behaviour resisting only the axial force in the bar direction. A bilinear idealization is adopted to model elasto-plastic stress-strain relationships. For the nonlinear anaysis, incremental load method combined with unbalanced load iterations for each load increment is used. To include time dependent effects of concrete, time domain is divided into several time steps which may have different length. Some numerical examples are presented to study the validity and applicability of the present method. The results are compared with experimental and numerical results obtained by other investigator.

• Textile Coloration and Finishing
• /
• v.1 no.1
• /
• pp.54-62
• /
• 1989

The woven fabric composed of nylon 6 filaments was treated with aqueous solutions (20, 30, 40, 50, 60%) of formic acid at 3$0^{\circ}C$ for 10 minutes under unrestrained condition, and the shrinkage behavior and some kinds of properties were examined. The shrinkages of the constituent yarns and fabric were increased with formic acid concentration, but they were lower than that of the original filaments because of fabric-structural factors. And the shrinkage of the warp was lower than that of the weft because of the residual stress from weaving process. By the restraint forces such as fabric-structural factors and residual stress, the constituent filaments were damaged partially at 60% of formic acid concentration and the degree of damage on the warp was greater than on the weft. And though the fabric count were increased overall, the spacing between the warps was decreased prior to the weft and eliminated nearly at 60% of formic acid concentration. The thickness, tensile strength, elongation, and handle value of fabric were increased overall with formic acid concentration excepting that the tensile strength for both the warp and weft directions and the elongation for the warp direction were decreased instead by the damage of yarns. But the crease recovery was decreased except the case of the weft direction at 60% of formic acid concentration.

• Korean Journal of Materials Research
• /
• v.9 no.7
• /
• pp.735-739
• /
• 1999

In this study we investigated stress development and shrinkage of thickness for a single $PbTiO_3$(PT) layer prepared by sol-gel processing. Changes of microhardness for multideposited PT layers with temperatures are also monitored to understand the densification of thin films. Single PT layer shrank rapidly from room temperature to$ 220^{\circ}C$ yielding 83% of total shrinkage observed up to $500^{\circ}C$. A tensile stress of ~75MPa developed in an as-spun layer, and increased steadily beyond $130^{\circ}C$ until it reaches the maximum value of 147MPa at $250^{\circ}C$. The significant decrease of tensile stress in the film beyond $370^{\circ}C$ indicates that thermal expansion mismatch between the film and the substrate dominates the stress behavior in this temperature range. Microhardness of the multideposited coatings also increased rapidly above $300^{\circ}C$ regardless of the pyrolysis temperatures used. Large amount of perovskite phase formed in multideposited coatings after $550^{\circ}C$ may be due partly to enhanced homogeneous nucleation in the thicker coating.

• Journal of the Korea Concrete Institute
• /
• v.23 no.3
• /
• pp.257-264
• /
• 2011

This paper contains the experimental performance evaluation results of bond-type anchorage systems with the CFRP(carbon fiber reinforced polymer) tendon. The preliminary tests were performed to find the appropriate filling materials in the steel molds. A total of five materials including epoxy or cement mortar have been used as fillers in the steel molds. Results of the preliminary tests showed that specimen filled with non-shrinkage mortar showed maximum tensile strength. Based on the finding, the non-shrinkage mortar was selected as filler for anchoring CFRP tendons. Additional tests were performed as a parametric study to select proper size of steel molds such as external diameter, thickness, and length. The proper size of steel molds with non-shrinkage mortar was selected based on the test results, which gave stable tensile performance.

• Design & Manufacturing
• /
• v.17 no.4
• /
• pp.42-51
• /
• 2023

In this study, we investigated the injection molding technology of thick-walled light guides, which are parts that control the light source of automotive lamps. Through injection molding analysis, the gate position that can minimize product shrinkage and deformation was selected, and a mold reflecting the analysis results was manufactured to evaluate the effect of injection speed and holding pressure on transferability during micro-pattern molding through experiments. When designing an injection mold for products with varying thicknesses, it was found that installing the gate on the side of the thicker part was advantageous for reducing volume shrinkage and deformation. It was found that the effect of shrinkage due to thickness may be greater than the position of the gate on pattern transferability. The pattern transfer error decreased as the injection speed and holding pressure increased, and it was found that increasing the injection speed was relatively effective.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.3
• /
• pp.508-512
• /
• 1998

The NTC thermistors were sintered by using microwave hybrid heating method at $1100^{\circ}C$~$1300^{\circ}C$ and those electrical properties were investigated. The obtained $B_{25^{\circ}C/85^{\circ}C}$ values from temperature dependence of electrical resisitivity were around 3100~3200 K which were almost the same values as conventionally sintered ones. Compared with conventional sintering process, this process could complete whole sintering process within 20 minutes. This the processing time and energy consumption could be reduced through this rapid heating by using microwave hybrid heating.t there were showed only two peaks, glycolide melting peak and lower molecular weight melting peak without lauryl alcohol. Conversion increased slowly with the reaction time up to 50 minutes, and then gave a sudden increase above that. The reaction time to disappear in glycolide melting peak during polymerization was shortened with the increase of lauryl alcohol content. Zero-shear viscosity of polyglycolic acid decreased with the increase of free acid content in glycolide.ssional energy and bending hysteresis increased. \circled3 Surface characteristics such as friction coefficient and thickness variation of highly shrinkage fabrics became relatively roughened state. \circled4 Since stiffened and roughened characteristics of highly shrinkage fabrics, drapabilities of them were significantly lowered. Additionally thermal insulation property of high shrinkage fabric was higher than that of low shrinkage fabric due to bulky and thickened feature. From the results, it is considered that the silk fabrics with high filling shrinkage have the good bulkiness and heat keeping properties and thus they have the suitable characteristics for high quality men's and women's formal garments.