• Journal of Korean Society of Steel Construction
• /
• v.29 no.2
• /
• pp.111-122
• /
• 2017

In this paper, the applicability of a 1900mm-deep concrete-filled U-shaped composite beam to composite ordinary moment frames (C-OMFs) was investigated based on existing test results from smaller-sized specimens and supplemental numerical studies since full-scale seismic testing of such a huge sized beam is practically impossible. The key issue was the web local buckling of concrete-filled U section under negative bending. Based on 13 existing test results compiled, the relationship between web slenderness and story drift capacity was obtained. From this relationship, a 1900mm-deep mega beam, fabricated with 25mm-thick plate was expected to experience the web local buckling at 2% story drift and eventually reach a story drift over 3%, thus much exceeding the requirements of C-OMFs. The limiting width to thickness ratio according to the 2010 AISC Specification was shown to be conservative for U section webs of this study. The test-validated supplemental nonlinear finite element analysis was also conducted to further investigate the effects of the horizontal stiffeners (used to tie two webs of a U section) on web local buckling and flexural strength. First, it is shown that the nominal plastic moment under negative bending can be developed without using the horizontal stiffeners, although the presence of the stiffeners can delay the occurrence of web local buckling and restrain its propagation. Considering all these, it is concluded that the 1900mm-deep concrete-filled U-shaped composite beam investigated can be conservatively applied to C-OMFs. Finally, some useful recommendations for the arrangement and design of the horizontal stiffeners are also recommended based on the numerical results.

• Journal of Applied Biological Chemistry
• /
• v.61 no.2
• /
• pp.157-164
• /
• 2018

The purpose of this study was to develop a kelp (Laminaria japonica) product with optimal sensory and nutritional properties for eating as a snack by investigating its physicochemical properties and conducting sensory evaluation. A preliminary study using tripolypolyphosphate solution found that it was good for removing the fishy smell and for making it soft. We soaked the kelp in 0.3-0.4% sodium tripolyphosphate buffer and tested with or without baking. In searching for the optimal polyphosphate dilution concentration, soaking in 0.3-0.4% sodium tripolyphosphate resulted in the best texture and flavor. As kelp separates into thick or thin samples, thick kelp was best when soaked in 0.4% sodium tripolyphosphate buffer and thin soaked in 0.3%. The kelp snack made from the thick one (over 221 mm thickness) was better than the thin one. Baking improved the moisture, texture and feel of the kelp snack. Tripolyphosphate treatment affected protein contents and texture softening. The differences by baking and tripolyphosphate treatment were shown with electromicroscopic image. Kelp snacks with added sweet and hot taste were preferred to sour taste. In conclusion, in making kelp snacks, it is advisable to use a thick kelp, 0.3-0.4% sodium tripolyphosphate, and baking treatment for better texture and feel. This kelp snack has low fishy smell, better taste and soft feel. Further research is needed to support sea food's importance, and usefulness of the kelp snack to help prevent goiter in inland province citizens.

• Journal of Animal Science and Technology
• /
• v.52 no.4
• /
• pp.259-264
• /
• 2010

This study was carried out to estimate genetic parameters and breeding values of Hanwoo cows for carcass traits. Carcass records were collected from Korean steers raised at the private farms located in rural area of Gangwon-do and slaughtered from December 2004 to June 2008 at the three slaughter houses near fattening farm. The results obtained in this study were summarized as follows; The means and standard deviations of the carcass traits were $5.57{\pm}2.01$ for marbling score (MS), $10.87{\pm}4.06mm$ for backfat thickness (BFT), $87.87{\pm}9.07cm^2$ for eye muscle area (EMA), $426.75{\pm}49.27kg$ for carcass weight (CW), and $65.80{\pm}3.80$ for yield index (YI). Heritability estimates using single trait analyses were 0.36 for MS, 0.35 for BFT, 0.24 for EMA, 0.29 for CW, and 0.40 for YI, respectively. Genetic correlation coefficients of MS with BFT, EMA, CW, and YI were -0.21, 0.30, -0.21 and 0.30, and those of BFT with EMA, CW and YI were -0.12, 0.57 and -0.97, and those of EMA with CW and YI were 0.32 and 0.27, respectively. And genetic correlation of CW with YI was -0.62. Single trait selection for MS might lead to reducing BFT, but might be an obstacle to increase CW due to negative genetic correlations of MS with BFT and CW.

• Journal of Biomedical Engineering Research
• /
• v.25 no.4
• /
• pp.253-259
• /
• 2004

in this study, we developed a Monte Carlo imaging simulation code written by the visual C$\^$++/ programing language for design optimization of a digital X-ray imaging system. As a digital X-ray imaging system, we considered a Gd$_2$O$_2$S(Tb) scintillator and a photosensor array, and included a 2D parallel grid to simulate general test renditions. The interactions between X-ray beams and the system structure, the behavior of lights generated in the scintillator, and their collection in the photosensor array were simulated by using the Monte Carlo method. The scintillator thickness and the photosensor array pitch were assumed to 66$\mu\textrm{m}$ and 48$\mu\textrm{m}$, respertively, and the pixel format was set to 256 x 256. Using the code, we obtained X-ray images under various simulation conditions, and evaluated their image qualities through the calculations of SNR (signal-to-noise ratio), MTF (modulation transfer function), NPS (noise power spectrum), DQE (detective quantum efficiency). The image simulation code developed in this study can be applied effectively for a variety of digital X-ray imaging systems for their design optimization on various design parameters.

• The Journal of Korean Society for Radiation Therapy
• /
• v.20 no.1
• /
• pp.37-43
• /
• 2008

Purpose: To evaluate dosimetry results of three different techniques for whole breast irradiation after conservative surgery of large pendulous breast patient. Materials and Methods: Planning computed tomography (CT) scans for three techniques were performed on a GE Hi-speed advantage CT scanner in the supine (SP), supine with breast supporting Device (SD) and prone position on a custom prone mattress (PP). Computed tomography images were acquired at 5 mm thickness. The clinical target volumes (CTV), ipsilateral lung and heart were delineated to evaluate the dose statistic, and all techniques were planned with the tangential photon beams (Pinnacle$^3$, Philips Medical System, USA). The prescribed dose was 50 Gy delivered in 25 fractions. To evaluate the dose coverage for CTV, we analysed percent volume of CTV receiving minimum of 95%, 100%, 105%, and 110% of prescription dose ($V_{95}$, $V_{100}$, $V_{105}$, and $V_{110}$) and minimal dose covering 95% ($D_{95}$) of CTV. The dosimetric comparison for heart and ipsilateral lung was analysed using the minimal dose covering 5% of each organs ($D_5$) and the volume that received >18 Gy for the heart and >20 Gy for the ipsilateral lung. Results: Target volume coverage ($V_{95}$ and $V_{100}$) was not significantly different for all technique. The V105 was lower for PP (1.2% vs. 4.4% for SP, 11.1% for SD). Minimal dose covering 95% ($D_{95}$) of target was 47.5 Gy, 47.7 Gy and 48 Gy for SP, SD and PP. The volume of ipsilateral lung received >20 Gy was 21.7%, 11.6% and 4.9% for SP, SD and PP. The volume of heart received >18 Gy was 17.0%, 16.1% and 9.8% for SP, SD and PP. Conclusion: Prone positioning of patient for large pendulous breast irradiation enables improving dose uniformity with minimal heart and lung doses.

• The Journal of Korean Society for Radiation Therapy
• /
• v.24 no.1
• /
• pp.31-37
• /
• 2012

Purpose: This study evaluated the usefulness of Helmet bolus device using Bolx-II, paraffin wax, solid thermoplastic material in total scalp irradiation. Materials and Methods: Using Rando phantom, we applied Bolx-II (Action Products, USA), paraffin wax (Densply, USA), solid thermoplastic material (Med-Tec, USA) on the whole scalp to make helmet bolus device. Computed tomography (GE, Ultra Light Speed16) images were acquired at 5 mm thickness. Then, we set up the optimum treatment plan and analyzed the variation in density of each bolus (Philips, Pinnacle). To evaluate the dose distribution, Dose-homogeneity index (DHI, $D_{90}/D_{10}$) and Conformity index (CI, $V_{95}/TV$) of Clinical Target Volume (CTV) using Dose-Volume Histogram (DVH) and $V_{20}$, $V_{30}$ of normal brain tissues. we assessed the efficiency of production process by measuring total time taken to produce. Thermoluminescent dosimeters (TLD) were used to verify the accuracy. Results: Density variation value of Bolx-II, paraffin wax, solid thermoplastic material turned out to be $0.952{\pm}0.13g/cm^3$, $0.842{\pm}0.17g/cm^3$, $0.908{\pm}0.24g/cm^3$, respectively. The DHI and CI of each helmet bolus device which used Bolx-II, paraffin wax, solid thermoplastic material were 0.89, 0.85, 0.77 and 0.86, 0.78, 0.74, respectively. The result of Bolx-II was the best. $V_{20}$ and $V_{30}$ of brain tissues were 11.50%, 10.80%, 10.07% and 7.62%, 7.40%, 7.31%, respectively. It took 30, 120, 90 minutes to produce. The measured TLD results were within ${\pm}7%$ of the planned values. Conclusion: The application of helmet bolus which used Bolx-II during total scalp irradiation not only improves homogeneity and conformity of Clinical Target Volume but also takes short time and the production method is simple. Thus, the helmet bolus which used Bolx-II is considered to be useful for the clinical trials.

• Restorative Dentistry and Endodontics
• /
• v.32 no.5
• /
• pp.419-425
• /
• 2007

The aim of this study was to evaluate the radiopacity and cytotoxicity of three resin-based (AH 26, EZ fill and AD Seal), a zinc oxide-eugenol-based (ZOB Seal), and a calcium hydroxide-based (Sealapex) root canal sealers. Specimens, 10 mm in diameter and 1 mm in thickness, were radiographed simultaneously with an aluminum step wedge using occlusal films, according to ISO 6876/2001 standards. Radiographs were digitized, and the radiopacity of sealers was compared to the different thicknesses of the aluminum step wedge, using the Scion image software. Using the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay, the cytotoxicity of each material was determined in immortalized human periodontal ligament (IPDL) cells. The results demonstrated that EZ fill was the most radiopaque sealer, while Sealapex was the least radiopaque (p < 0.05). AH 26, AD Seal and ZOB Seal presented intermediate radiopacity values. All the materials evaluated, except for Sealapex, presented the minimum radiopacity required by ISO standards. The cell viabilities of resin-based root canal sealers were statistically higher than that of other type of root canal sealers through the all experimental time. Further, EZ fill showed statistically lower cell viability in 24 and 48 hours compared to AD Seal and in 72 hours compared to all other resin-based root canal sealers. However, there was no correlation between the radiopacity and cytotoxicity of three resin-based root canals sealers (p > 0.05). These results indicate that resin-based root canal sealer is more biocompatible and has advantage in terms of radiopacity.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.23 no.3
• /
• pp.249-257
• /
• 2007

State of problem : The use of zirconium oxide all-ceramic material provides several advantages, including a high flexural strength(>1000MPa) and desirable optical properties, such as shading adaptation to the basic shades and a reduction in the layer thickness. Along with the strength of the materials, the cementation technique is also important to the clinical success of a restoration. Nevertheless, little information is available on the effect of different surface treatments on the bonding of zirconium high-crystalline ceramics and resin luting agents. Purpose : The aim of this study was to test the effects of surface treatments of zirconium on shear bond strengths between bovine teeth and a zirconia ceramic and evaluate differences among cements Material and methods : 54 sound bovine teeth extracted within a 1 months, were used. They were frozen in distilled water. These were rinsed by tap water to confirm that no granulation tissues have left. These were kept refrigerated at $4^{\circ}C$ until tested. Each tooth was placed horizontally at a plastic cylinder (diameter 20mm), and embedded in epoxy resin. Teeth were sectioned with diamond burs to expose dentin and grinded with #600 silicon carbide paper. To make sure there was no enamel left, each was observed under an optical microscope. 54 prefabricated zirconium oxide ceramic copings(Lava, 3M ESPE, USA) were assigned into 3 groups ; control, airborne-abraded with $110{\mu}m$ $Al_2O_3$ and scratched with diamond burs at 4 directions. They were cemented with a seating force of 10 ㎏ per tooth, using resin luting cement(Panavia $F^{(R)}$), resin cement(Superbond $C&B^{(R)}$), and resin modified GI cement(Rely X $Luting^{(R)}$). Those were thermocycled at $5^{\circ}C$ and $55^{\circ}C$ for 5000 cycles with a 30 second dwell time, and then shear bond strength was determined in a universal test machine(Model 4200, Instron Co., Canton, USA). The crosshead speed was 1 mm/min. The result was analyzed with one-way analysis of variance(ANOVA) and the Tukey test at a significance level of P<0.05. Results : Superbond $C&B^{(R)}$ at scratching with diamond burs showed the highest shear bond strength than others (p<.05). For Panavia $F^{(R)}$, groups of scratching and sandblasting showed significantly higher shear bond strength than control group(p<.05). For Rely X $Luting^{(R)}$, only between scratching & control group, significantly different shear bond strength was observed(p<.05). Conclusion : Within the limitation of this study, Superbond $C&B^{(R)}$ showed clinically acceptable shear bond between bovine teeth & zirconia ceramics regardless of surface treatments. For the surface treatment, scratching increased shear bond strength. Increase of shear bond strength by sandblasting with $110{\mu}m$ $Al_2O_3$ was not statistically different.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.38 no.9
• /
• pp.1195-1201
• /
• 2009

Dietary effects of Agaricus bisporus powder (ABP) on the quality characteristic of eggs from hens (Hy-Line) were investigated. Experimental groups (100 hens/group) were divided into normal control group (Control), 0.3% ABP supplemented diet group (M-0.3) and 0.6% ABP supplemented diet group (M-0.6), then fed for 12 weeks. There were no significant differences in shell thickness, while Haugh unit in M-0.3 and M-0.6 groups were 18.3$\sim$27.6% higher than that of control groups. Color $L^*$ and $b^*$ values of egg albumen and yolk in the M-03 and M-0.6 groups were lower whereas $a^*$ values were higher than those of NC group. In the yolk of M-03 and M-0.6 groups compared with control groups, the levels of total phospholipids and HDL-cholesterol were 4.5$\sim$13.9% and 86.1$\sim$87.0% higher, respectively, while the levels of total cholesterol, triglyceride and LDL-cholesterol were 29.4$\sim$31.9%, 51.9$\sim$52.4% and 49.1$\sim$53.5% lower than those of control groups, respectively. There were no significant differences in fatty acids. In the result of sensory evaluation, gory odor of raw eggs in the M-03 and M-0.6 groups was slightly lower compared with control groups. These results suggest that the feed containing mushroom of Agaricus bisporus can be used to reduce the egg yolk cholesterol content and gory odor from raw egg, and also to increase the phospholipids as a functional feed. Further studies on the mechanism are required.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.21 no.1
• /
• pp.21-29
• /
• 1988

This study was carried out to develop the powdered Katsuobushi (a kind of boiled, smoked, and dried fish product which is used for seasoning soup as it is.) using skipjack as a natural flavoring substance. The processing conditions of the powdered Katsuobushi and the changes of taste compounds during processing of the products were examined. In preparation of the powdered Katsuobushl, frozen skipjack was thawed, beheaded, gutted, filleted and then sliced to 1cm of thickness. The silted meats were boiled in skipjack extract for 20 minutes, and then it was smoked for, 3 times to $10\~12\%$ moisture content at $80^{\circ}C$ for 8 hours. The smoked - dried meats were followed to be 50 mesh of particle size. The effect of slicing and boiling in skipjack meat extract on enhancing flavor and on preventing lipid oxidation of product during processing were observed. The moisture content and crude lipid content of the powdered Katsuobushi was in the range of 11 to $12\%$ and 4.3 to $4.8\%$, respectively. The taste compounds of the product were nucleotides and their related compounds, 1135.8mg/100g ; free amino acid and related compounds, 2210.2mg/100g ; non-volatile organic acids, 1148.0mg/100g ; and total creatinine. 592.1mg/100g on dry basis, and small amount of betaine and TMAO. The major elements of mineral in the product were found to be K, Mg, Na, and Ca. The content of IMP was 542.0mg/100g, and major free amino acids were found to be histidine, anserine, taurine, carnosine and alanine of which occupied to $83.6\%$ of total free amino acids. In non -volatile organic acids, major ones were lactic acid, succinic acid, pyroglutamic acid and $\alpha-ketoglutaric$ acid. From the results of the chemical experiments and sensory evaluation, we may conclude that the flavor of the product from present experiment is more desirable than that of conventional products although the processing time used were much shortened than that of conventional method, and it can be commercialized as a seasoning powder.