• Journal of Sensor Science and Technology
• /
• v.4 no.2
• /
• pp.3-6
• /
• 1995

Type K thermocouples having multi-junction for measuring the temperature gradient of the furnace were fabricated. The obtained results on the temperature gradient of the electric furnace maintained at $800^{\circ}C$ were consistent with those for the reference grade type S thermocouple, which was carefully calibrated, within the permitted error limit of the type K thermocouple. It was suggested that noble metal multi-junction thermocouples be suitable for more accurate temperature gradient measurements.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.742-747
• /
• 2006

This paper describes online stator-resistance estimation of a linear induction motor(LIM) with cage-type secondary using direct thrust control(DTC), where the resistance value is derived from stator-winding temperature estimation using thermocouple. In this paper, corrected stator resistance has an error in actuality measurement resistance. So compensation coefficient $\kappa$ which is decided through comparison and verifying several times relation of calculated resistance and measured motor line-line resistance. The stator-winding temperature information can also be used for monitoring, protection, and fault-tolerant control of the machine. Also, this paper reports the LIM's responses of the flux measured by the proposed stator resistance compensation algorithm.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.2
• /
• pp.69-76
• /
• 1993

The program for the development of linkage system was made and the scissors-type linkage system was designed. The piston temperature distribution under steady state was measured by the linkage system and thermocouple. The effects of engine speed, coolant outlet temperature, and torque on the piston temperature were investigated.

• Applied Microscopy
• /
• v.45 no.2
• /
• pp.95-100
• /
• 2015

The in-situ heating transmission electron microscopy experiment allows us to observe the time- and temperature-dependent dynamic processes in nanoscale materials by examining the same specimen. The temperature, which is a major experimental parameter, must be measured accurately during in-situ heating experiments. Therefore, calibrating the thermocouple readout of the heating holder prior to the experiment is essential. The calibration can be performed using reference materials whose phase-transformation (melting, oxidation, reduction, etc.) temperatures are well-established. In this study, the calibration experiment was performed with four reference materials, i.e., pure Sn, Al-95 wt%Zn eutectic alloy, NiO/carbon nanotube composite, and pure Al, and the calibration curve and formula were obtained. The thermocouple readout of the holder used in this study provided a reliable temperature value with a relative error of <4%.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.6
• /
• pp.687-695
• /
• 2015

An experimental study on the automation of the coffee roasting process was conducted. For this study, a temperature sensor, controllers, and motors were added to a manually operated coffee roaster. The temperature, time, and exhausting damper control were selected as the control parameters. The thermocouple measurements were severely influenced by the thermocouple size and location of the roaster. As a result, the standard thermocouple size and location of the roaster were experimentally set to show a similar trend of temperature change by using a previously installed thermometer. A standard roasting process was chosen through repeated roasting experiments and the advice of a roasting expert. The automation of the roasting process was successfully executed using temperature criteria, such as the bean input and first and second crack occurrence, and by controlling the exhausting damper opening time. The control parameters and roaster skills can be used for similar types of roasters for process automation.

• Journal of Sensor Science and Technology
• /
• v.13 no.6
• /
• pp.405-410
• /
• 2004

Compensation wires for Pt/Pd thermocouple was manufactured using Cu/Ni alloys. Their thermoelectric voltage has been tested from room temperature to about $150^{\circ}C$. Alloys of $Cu_{95.5}Ni_{4.5}$ and $Cu_{89.5}Ni_{10.5}$ introduced only small emf differences to Pt/Pd thermocouples, indicating a real possibility of industrial use. Above $1000^{\circ}C$, the temperature difference was expected to he small as ${\pm}0.5^{\circ}C$, and the difference would be minimized by adjusting the Ni content with a small amount.

• 전자공학회논문지 IE
• /
• v.44 no.1
• /
• pp.6-9
• /
• 2007

Twenty four types of thermopile for micro spectrometer infrared sensors were fabricated on low-stress Si3N4 membranes with $l.2{\mu}m-thickness$ using MEMS technology. Thermopile were designed and fabricated for optimum conditions by five parameters of thermocouple numbers $(16\sim48)$, thermocouple line widths $(10{\mu}m-25{\mu}m)$, thermocouple lengths $(100{\mu}m-500{\mu}m)$, membrane areas $(12mm2\sim2.52mm2)$ and junction areas $(150{\mu}m2\sim750{\mu}m2)$, respectively. It was thought that measurement results could be used for thermopile infrared sensors optimum structure for micro spectrometers.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.7
• /
• pp.863-870
• /
• 2004

The temperature and soot particle measurement technique in a laminar diffusion flame has been studied to investigate the characteristics of soot particle with temperature using a co-flow burner. The temperature distribution in the flame were measured by rapid insertion of a R-type thermocouple and the soot particles by LEM/LIS techniques. In these measurement, soot volume fraction, number density and soot diameters were analyzed experimentally. As a results, the spacial distributions of particle volume fraction, soot diameter, and number density are mapped throughout the flame using the Rayleigh theory for the scattering of light by particles. A laser extinction method was used to measure the soot volume fraction and laser induced scattering method was used to measure the soot particle diameter and number density. Also, we measured temperature without the effect of soot particles attached to the thermocouple junction, which is close to the nozzle. In this result, we found that upstream zone has a unstable flowing in co-flow diffusion flame and the y-axis temperature of flame has a uniform temperature distribution in the most soot volume fraction zone.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1267-1273
• /
• 2004

The temperature and soot particle measurement technique in a laminar diffusion flame have been studied to investigate the characteristics of soot particle with temperature using a co-flow burner. The temperature distributions in the flame were measured by rapid insertion of a R-type thermocouple and the soot particles were detected were detected by LEM/LIS techniques. In these measurement, soot volume fraction, number density and soot diameters were analyzed experimentally. As a results, the spacial distributions of particle volume fraction, soot diameter, and number density are mapped throughout the flame using the Rayleigh theory for the scattering of light by absorbing particles. A laser extinction method was used to measure the soot volume fraction and Laser induced scattering method was used to measure the soot particle diameter and number density. Also, we measured temperature without the effect of soot particles attached to the thermocouple junction, which is close to the nozzle. In this result, we found that upstream zone has a unstable flowing in co-flow diffusion flame and the y-axis temperature of flame has a uniform temperature distribution in the most soot volume fraction zone.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.3
• /
• pp.133-138
• /
• 2003

As concrete structures are heated, thermal strain can be developed. Because of the boundary conditions, the thermal stress may be arisen. Thermal strain and temperature were measured simultaneously using an optical fiber sensor. Fiber Bragg Grating Sensor(FBG sensor) was used in the measurement. Because it can measure the strains more than two points with one line, it was possible to measure both thermal strain and temperature with one line. To compare data measured by FBG sensor, strain and temperature were measured using strain gauge and thermocouple. The FBG sensor could measure the strain under the temperature greater than $60^{\circ}C$ but strain gauge couldn't. Both the FBG temperature sensor and thermocouple could measure the temperature and the results are related each other linearly.