• Korean Chemical Engineering Research
• /
• 제61권1호
• /
• pp.32-38
• /
• 2023

In this study, the electrochemical properties of dopamine coated silicon/silicon carbide/carbon(Si/SiC/C) composite materials were investigated to improve cycle stability and rate performance of silicon-based anode active material for lithium-ion batteries. After synthesizing CTAB/SiO₂ using the Stöber method, the Si/SiC composites were prepared through the magnesium thermal reduction method with NaCl as heat absorbent. Then, carbon coated Si/SiC anode materials were synthesized through polymerization of dopamine. The physical properties of the prepared Si/SiC/C anode materials were analyzed by SEM, TEM, XRD and BET. Also the electrochemical performance were investigated by cycle stability, rate performance, cyclic voltammetry and EIS test of lithium-ion batteries in 1 M LiPF₆ (EC: DEC = 1:1 vol%) electrolyte. The prepared 1-Si/SiC showed a discharge capacity of 633 mAh/g and 1-Si/SiC/C had a discharge capacity of 877 mAh/g at 0.1 C after 100 cycles. Therefore, it was confirmed that cycle stability was improved through dopamine coating. In addition, the anode materials were obtain a high capacity of 576 mAh/g at 5 C and a capacity recovery of 99.9% at 0.1 C/0.1 C.

• Journal of Electrical Engineering and Technology
• /
• 제5권2호
• /
• pp.342-351
• /
• 2010

The SiC-$ZrB_2$ composites were fabricated by combining 30, 35, 40, 45 and 50 vol. % of zirconium diboride ($ZrB_2$) powders with silicon carbide (SiC) matrix. The SiC-$ZrB_2$ composites and the sintered compacts were produced through spark plasma sintering (SPS) under argon atmosphere, and its physical, electrical, and mechanical properties were examined. Also, the thermal image analysis of the SiC-$ZrB_2$ composites was examined. Reactions between $\beta$-SiC and $ZrB_2$ were not observed via x-ray diffraction (XRD) analysis. The apparent porosity of the SiC+30vol.%$ZrB_2$, SiC+35vol.%$ZrB_2$, SiC+40vol.%$ZrB_2$, SiC+45vol.%$ZrB_2$ and SiC+50vol.%$ZrB_2$ composites were 7.2546, 0.8920, 0.6038, 1.0981, and 10.0108%, respectively. The XRD phase analysis of the sintered compacts demonstrated a high phase of SiC and $ZrB_2$. Among the $SiC+ZrB_2$ composites, the SiC+50vol.%$ZrB_2$ composite had the lowest flexural strength, 290.54MPa, the other composites had more than 980MPa flexural strength except the SiC+30vol.%$ZrB_2$ composite; the SiC+40vol.%$ZrB_2$ composite had the highest flexural strength, 1011.34MPa, at room temperature. The electrical properties of the SiC-$ZrB_2$ composites had positive temperature coefficient resistance (PTCR). The V-I characteristics of the SiC-$ZrB_2$ composites had a linear shape in the temperature range from room to $500^{\circ}C$. The electrical resistivities of the SiC+30vol.%$ZrB_2$, SiC+35vol.%$ZrB_2$, SiC+40vol.%$ZrB_2$ SiC+45vol.%$ZrB_2$ and SiC+50vol.%$ZrB_2$ composites were $4.573\times10^{-3}$, $1.554\times10^{-3}$, $9.365\times10^{-4}$, $6.999\times10^{-4}$, and $6.069\times10^{-4}\Omega{\cdot}cm$, respectively, at room temperature, and their resistance temperature coefficients were $1.896\times10^{-3}$, $3.064\times10^{-3}$, $3.169\times10^{-3}$, $3.097\times10^{-3}$, and $3.418\times10^{-3}/^{\circ}C$ in the temperature range from room to $500^{\circ}C$, respectively. Therefore, it is considered that among the sintered compacts the SiC+35vol.%$ZrB_2$, SiC+40vol.%$ZrB_2$ and SiC+45vol.%$ZrB_2$ composites containing the most outstanding mechanical properties as well as PTCR and V-I characteristics can be used as an energy friendly ceramic heater or ohmic-contact electrode material through SPS.

• Journal of Bio-Environment Control
• /
• 제18권4호
• /
• pp.332-340
• /
• 2009

In this study, the thermal insulation effectiveness of the greenhouse insulators by the installation methods was investigated to find the right installation way of the insulation materials. Physical properties of the insulators such as thickness, air transmissivity, apparent density, ultraviolet rays cutoff ratio, reflectance, thermal conductivity, moisture absorptivity were evaluated and the insulation ability of the insulators were measured by the module experiments. For the same insulator, the insulation ability of the case with the outward direction of the black colored face, i.e., with the inward direction of the white colored face, was better than that of vice versa. The case of the black colored both surfaces was better than the case of the white colored both surfaces. For aluminium reflection material, the case with the outward direction of the lustre face, i.e., with the inward direction of the non-lustre face, was better than that of vice versa. For the same material with the inner thin polyethylene foam (or polyester) and the chemical wool, the case with the outward direction of the inner thin polyethylene foam (or polyester), i.e., with the inward chemical wool, was better than that of vice versa. Addition of the inner thin polyethylene foam increased the insulation effect very much.

• Korean journal of applied entomology
• /
• 제12권3호
• /
• pp.93-107
• /
• 1973

Garlic (Allium sativum L.) is an important vegetable crop for the Korean people and has long been cultivated extensively in Korea. More recently it has gained importance as a source of certain pharmaceuticals. This additional use has also contributed to the increasing demand for Korean garlic. Garlic has been propagated vegetatively for a long time without control measures against virus diseases. As a result it is presumed that most of the garlic varieties in Korea may have degenerated. The production of virus-free plants offers the most feasible way to control the virus diseases of garlic. However, little is known about garlic viruses both domestically and in foreign countries. More basic information regarding garlic viruses is needed before a sound approach to the control of these diseases can be developed. Currently garlic mosaic disease is most prevalent in plantings throughout Korea and is considered to be the most important disease of garlic in Korea. Because of this importance, studies were initiated to isolate and characterize the garlic mosaic virus. Symptom expression in test plants, physical properties, purification, serological reaction and morphological characteristics of the garlic mosaic virus were determined. Results of these studies are summarized as follows. 1. Surveys made throughout the important garlic growing areas in Korea during 1970-1972 revealed that most of the garlic plants were heavily infected with mosaic disease. 2. A strain of garlic mosaic virus was obtained from infected garlic leaves and transmitted mechanically to Chenopodium amaranticolor by single lesion isolation technique. 3. The symptom expression of this garlic mosaic virus isolate was examined on 26 species of test plants. Among these, Chenopodium amaranticolor, C. quince, C. album and C. koreanse expressed chlorotic local lesions on inoculated leaves 11-12 days after mechanical inoculation with infective sap. The remaining 22 species showed no symptoms and no virus was recovered from them whet back-inoculated to C. amaranticolor. 4. Among the four species of Chtnopodium mentioned above, C. amaranticolor and C. quinoa appear to be the most suitable local lesion test plants for garlic mosaic virus. 5. Cloves and top·sets originating from mosaic infected garlic plants were $100\%$ infected with the same virus. Consequently the garlic mosaic virus is successively transmitted through infected cloves and top-sets. 6. Garlic mosaic virus was mechanically transmitted to C, amaranticolor when inoculations were made with infective sap of cloves and top-sets. 7. Physical properties of the garlic mosaic virus as determined by inoculation onto C. amaranticolor were as follows. Thermal inactivation point: $65-70^{\circ}C$, Dilution end poiut: $10^-2-10^-3$, Aging in vitro: 2 days. 8. Electron microscopic examination of the garlic mosaic virus revealed long rod shaped particles measuring 1200-1250mu. 9. Garlic mosaic virus was purified from leaf materials of C. amaranticolor by using two cycles of differential centrifugation followed by Sephadex gel filtration. 10. Garlic mosaic virus was successfully detected from infected garlic cloves and top-sets by a serological microprecipitin test. 11 Serological tests of 150 garlic cloves and 30 top-sets collected randomly from seperated plants throughout five different garlic growing regions in Korea revealed $100\%$ infection with garlic mosaic virus. Accordingly it is concluded that most of the garlic cloves and top-sets now being used for propagation in Korea are carriers of the garlic mosaic virus. 12. Serological studies revealed that the garlic mosaic virus is not related with potato viruses X, Y, S and M. 13. Because of the difficulty in securing mosaic virus-free garlic plants, direct inoculation with isolated virus to the garlic plants was not accomplished. Results of the present study, however, indicate that the virus isolate used here is the causal virus of the garlic mosaic disease in Korea.

• Journal of the Korean Wood Science and Technology
• /
• 제44권3호
• /
• pp.370-380
• /
• 2016

The black pine logs damaged by pine wilt disease in Jeju-do were heat-treated to extend the utilization of domestic trees damaged by pine wilt disease. The heat-treatment of wood requires wood to be heated to $56^{\circ}C$ for 30 min at the core. The average moisture content and top-diameter of the black pine logs were ranged from 46% to 141% and from 180 mm to 500 mm, respectively. And the basic specific gravity and oven-dry specific gravity of the black pine logs were 0.47 and 0.52, respectively. The time required for heat-treatment at $105^{\circ}C$ temperature was ranged from 7.7 h to 44.2 h, depending on moisture content and top-diameter. The temperature distribution was used to predict the time required for heat-treatment of black pine log with various moisture contents and top-diameters using finite difference method. The thermal properties of wood including the thermal conductivity and specific heat in accordance with moisture content were calculated. Heat transfer coefficient for mixed convection in form of adding natural convection and forced convection was used for heat transfer analysis. The error between the measured and predicted values ranged from 3% to 45%. The predicted times required for heat-treatment of black pine log with 50% moisture content and 200 mm, 300 mm, and 400 mm top-diameter were 10.9 h, 18.3 h, and 27.0 h, respectively. If the initial moisture content of black pine log is 75%, heat treatment times of 13.6 h, 22.5 h, and 32.8 h were predicted in accordance with top-diameter. And if the initial moisture content of black pine log is 100%, heat treatment times of 16.2 h, 26.5 h, and 38.2 h were predicted in accordance with top-diameter. When the physical properties of logs damaged by pine wilt disease are presented, these results can be applicable to the heat-treatment of red pine and Korean pine logs as well.

• Korean Journal of Heritage: History & Science
• /
• 제51권1호
• /
• pp.4-31
• /
• 2018

The Neolithic pottery excavated from the Jungsandong site has been classified into four types of pottery (I: feldspar type, II: mica type, III: talc type and IV: asbestos type) according to their mineral composition. These four types of potteries generally appear to have undergone incomplete firing, while the level of oxidation in the type I pottery objects, which have a relatively higher clay content, was found to be particularly low. The type III objects, which have a high talc content, are judged to have been somewhat slow in removing carbon because they contain saponite belonging to the smectite group. Of the four types of pottery, type IV showed the highest redness and the most uniform characteristics, thus indicating a good level of oxidation. In particular, fixed carbide (C; 33.7 wt.%) with a thickness of about 1mm, and originating from organic substances, was detected inside the walls of the type I pottery, while the deep radial cracks in the outer surfaces of the pottery are thought to have been caused by repeated thermal shocks. Given that all of the pottery except for the type I artifacts are considered to be have been made for storage purposes, those containing talc and tremolite are easy to done liquid storing vessels based on an analysis of their material characteristics. As for the type II relics, which are composed of various minerals and exhibit poor physical properties, they seem to have been used for simple storage purposes. As domestic talc and asbestos mines were concentrated in the areas of Gyeonggi, Gangwon, Chungbuk, and Chungnam, it seems likely that talc and tremolite were produced as contiguous minerals. Considering the distance between the remains in Jungsandong and these mines and their geographical distribution, there is a possibility - albeit somewhat slight - that these mines were developed for the mining of various minerals. Although ultramafic rock masses - such as serpentine capable of generating talc and tremolite - have not been found in the Jungsandong area, limestone and biotite granite containing mica schist have been identified in the northwestern part of Yeongjong Island, indicating that small rock masses might have formed there in the past. Therefore, it is judged necessary to accumulate data on pottery containing talc and tremolite, other than the remains in Jungsandong, and to investigate the rocks and soils in the surrounding area with greater precision. The firing temperatures of the pottery found at the Jungsandong site were interpreted by analyzing the stability ranges of the mineral composition of each type. As a result, they have been estimated to range from 550 to $800^{\circ}C$ for the type I artifacts, and from 550 to $700^{\circ}C$ for the type I, II and IV artifacts. However, these temperatures are not the only factors to have affected their physical properties and firing temperature, and the types, particle sizes, and firing time of the clay should all be taken into consideration.

• Korean Journal of Heritage: History & Science
• /
• 제55권4호
• /
• pp.138-164
• /
• 2022

The Neolithic shell midden in Daejuk-ri, Seosan, is distributed on the gentle slope of a low hill close to the west coast. The bedrock of the area consists mainly of schist with various mafic minerals, but shows a partial gneiss pattern. The site consists of loamy topsoil and clay loam subsoil, and the degree of siallization is relatively low. Although the pottery excavated from the shell midden shares mostly similar features, a variety of shapes and patterns coexist. The surface colors, thickness and physical properties are slightly different. The pottery can be subdivided into three types (IA, IB and II) according to the composition of the body clay, the temper and the existence of a black core. Types IA and IB are colorless mineral pottery with a non-black or black core respectively. TypeII is colored mineral pottery with a non-black core. Type I pottery also contains non-plastic colored minerals, but type II contains a large amount of biotite, chlorite, talc, amphibole, diopside and tremolite, which include a large amount of Mg and Fe. The studied pottery contains a small amount of organic matter. Considering the grain size and relatively poor sorting and roundness of the non-plastic particles, the pottery appears to be made by adding coarse non-plastic tempers for special purposes to the untreated weathered soil around the site. The three types of pottery seem to have been incompletely fired in general. While type IB has the lowest degree of oxidation, typeII shows the highest degree of redness and oxidation. It can be interpreted that these differences depend on the firing temperature and the ratio of non-plastic particles. Through a synthesis of the minerals, geochemical data and thermal history, it can be determined that the firing temperature ranged from 600 to 700℃. The pottery types of the Daejuk-ri Shell Midden have slightly different production conditions, mineral compositions, and physical properties, but have undergone similar production processes with basically the same clay materials. The clay is almost identical to the composition of the bedrock and weathered soil distributed in the Daejuk-ri area. Currently, there is an industrial complex in the area, so it is difficult to confirm the soil and geological distribution of the site. However, it is highly probable that the area around the site was self-sufficient for the clay and tempers required for the production of the Neolithic pottery. Therefore, it can be interpreted that the group that left the shell midden in Daejuk-ri lived near the site, visited the site for the purpose of collecting and processing shellfish, and discarded the broken pottery along with shells.

• Resources Recycling
• /
• 제17권6호
• /
• pp.62-67
• /
• 2008

Oil shale is a sedimentary rock that contains organic compounds called kerogen that are released as petroleum-like liquids by retorting. In order to evalute oil shale as alternative oil resources, the physical properties of oil shale samples from US and Russia were investigated and Fischer assays were carried out. Thermogravimetric analysis shows that thermal degradation of oil shale consisted of two stage processes, with hydrocarbon release from kerogen followed by $CO_2$ release by carbonate decomposition. Organic compounds in oil shale have an high hydrogen/carbon ratio, and therefore liquid hydrocarbons could be obtained easily. Shale oil yields from Russian and US oil shales by Fischer assay were 12.7% and 18.5%, respectively. The density and boiling point of shale oils are higher than that of Middle East crude oil, indicating that further upgrading processes are necessary for refinery. On the other hands, sulfur contents are relatively low, and the amounts of Vanadium and Nickel are extremely small in shale oil. It was found that paraffins were rich in US shale oil while main components of Russian shale oil were oxygenated hydrocarbons.

• Korean journal of applied entomology
• /
• 제15권3호
• /
• pp.137-145
• /
• 1976

Orchids have been propagated vegetatively for a long time without adequate control measures against virus diseases in Korea. As a result, it is presumed that most of the orchid varieties in Korea may have been degenerated. Nevertheless there has been little work on the virus diseases of orchids in Korea. Therefore studies were initiated to isolate an4 characterize the orchid viruses occurring in Korea. The results obtained are summerized as follows. 1. Symptoms of virus diseases on orchid varieties can be grouped 1) mosaic, 2) necrotic streak with mosaic, 3) ring necrosis, 4) chlorotkc ring and 5) necrotic spot. 2. A total of 102 orchid plants representing 4 genera were investigated on the occurrence of Cymbidium mosaic virus and tobacco mosaic virus by serological agar-gel double diffusion test. The test revealed that approximately $45\%$ of the orchids were infected with Cymbidium mosaic virus. None of the plants were found to be infected with tobacco mosaic virus. 3. Local lesions appeared on the inoculated leaves of Chenopodium amaranticolor Cassia occidentalis and Datura stramonium 7-12 days after mechanical inoculation with Cymbidium mosaic virus. 4. Physical properties of the Cymbidium mosaic virus determined by inoculation on Chenopodium amaranticolor were as follows: Thermal inactivation Point; $75-80^{\circ}C$, dilution end Point; $10^{-5}-10^{-6}\%$ aging in vitro; 8 days. 5. Three different buffers at pH 7.0 and pH 9.0 were compared for the efficiency of agar-gel double diffusion test with Cymbidium mosaic virus. Phosphate, imidazol and tris buffer at pH 7.0 gave equally satisfactory results. 6. Electron microscopic examination of the Cymbidium mosaic virus revealed rod shaped particles measuring 460-580mu.

• Korean Journal Plant Pathology
• /
• 제1권1호
• /
• pp.3-11
• /
• 1985

Three mild mutant strains of tobacco mosaic virus (TMV) were isolated from Nicotiana tabacum var. Samsun incubated at $38^{\circ}C$ for 10 days after inoculation with a wild type of TMV-OM strain. They were designated into Tg 5272, Tw 227 and Tw 333. All mild strains could be distinguished from TMV-OM by their reactions on different indicator plants. The mild strains induced the mild mottling without distinct symptoms, whereas the wild strain produced severe mosaic, rugose and stunting on tobacco and red pepper plants. Tw 227 and Tw 333 produced smaller necrotic spots than those of Tg 5272 and TMV-OM on N. glutinosa and Datura stramonium. The former two strains also produced ring spots and mosaic on Gomphrena globosa compared with necrotic spots by the latter strains. Three mild strains were serologically identical to TMV-OM. Their physical properties were thermal inactivation point $80-85^{\circ}C$, dilution end point between $10^{-4}\;and\;10^{-6}$, and longevity in vitro 7days or longer. Ultraviolet absorption spectra of purified preparations of the mild strains and TMV-OM were identical, with a minimum at 247nm, a maximum at 260nm, and a slight shoulder at 290nm. Electrophoresis of the strains in polyacrylamide-agarose gel showed that all the strains formed one major band and two minor bands, except for one minor band of Tw 333. However, when sodium dodecyl sulfate was added to the purified viruses before electrophoresis, each strain formed only one major band.