• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.545-548
• /
• 2002

$(Ba_{0.6-x}Sr_{0.4}Ca_x)TiO_3$(BSCT) (x=0.10, 0.15, 0.20) powders were prepared by the sol-gel method and BSCT thick films were fabricated by the screen-printing method. The structural properties as a faction of the composition ratio were studied. As a result of the differential thermal analysis (DTA), exothermic perk was observed at around $860^{\circ}C$ dne to the formation of the polycrystalline perovskite phase. The BSCT thick films sintered at $1350^{\circ}C$ for 2h showed the average grain size of $2{\sim}7{\mu}m$. The average thickness of BSCT thick films, obtained by 3 times of screen-printing, was approximately $85{\mu}m$.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.230-231
• /
• 2018

Recently, the danger for radioactive materials has become a hot topic. Beginning with the Chernobyl nuclear accident in 1996, in 2011, the Fukushima nuclear power plant in Japan suffered major damage such as large-scale casualties and radioactive dangerous area selection. Concerns about leakage of radioactive materials due to recent earthquakes have been deepening in Korea, such as Wolsong Nuclear Power Plant in Gyeongju, and there is a growing interest in the safety of radioactive materials through the media and the media. However, the route to exposure to radioactive materials is not limited to these large-scale nuclear accidents. Typical examples of this are radioactive substances exposed in daily life. In the case of radon gas, the danger is being revealed through current events programs and news, and natural radiation exposure is attracting attention.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.33-36
• /
• 2005

Colloidal Silica(CS)/silane sol solutions were prepared in variation with synthesizing parameters such as ratio of CS to silane and reaction time. In the case of LHSA CS/tetramethoxysilane(TMOS)/methyltrimethoxysilane(MTMS) CS/silane sol, coating film had stable contact angle with increasing reaction time excepting for 48hours. Also, the LHSA CS/TMOS/MTMS coating film had more enhanced flat surface with increasing the amount of MTMS and increasing reaction time. In the case of thermal stability, thermal dissociation of LHSA CS/MTMS sol did not occur up to $550^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.25 no.2
• /
• pp.136-142
• /
• 1988

β-Al2O3, which is used for solid electrolyte membrances in sodium-sulfur batteries, was prepared by sol-gel process. Sodium-n-propoxide NaOC3H7 and aluminum-isopropoxide Al(OC3H7)3 were hydrolyzated in the solution at pH 3, pH 7, pH 9 and pH 11, respectively. The sol-gel processed samples were calcined at several temperature steps, respectively and analysed by thermal analyser(DT-TGA), infrared spectrum analyser and X-ray diffraction analyser. The gelling rate of solution at pH 7 was much higher than that of the solution at pH 3. Thermal exchanging behavior of the gels at pH 3 were similar to Na2O·Al2O3·6H2O and, above pH 7, were similar to Na2O·Al2O3·3H2O. When samples' composition ratio was 9.13 : 90.87 [NaOC3H7:Al(OC3H7)3] at pH 7, β-Al2O3 was formed at 1100℃.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.12
• /
• pp.1181-1186
• /
• 2000

The structural evolution during the thermal treatment of $70SiO_2-3OTiO_2(mole%)$ sol-gel derived powders and films was investigated by FT-IR, Raman and XPS, and XRD. From these results, the $TiO_2-rich$ regions involving $Ti^{4+}$ ions in octahedral coordination were confirmed to be amorphous at $600^{\circ}C$. However, Raman spectra along with XRD patterns indicated that at high temperature (above $700^{\circ}C)$, the amorphous $TiO_2was$ segregating to form anatase crystal. Also, the effect of experimental variables such as thermal treatment, heating rate and exposure to water vapor on structural changes, refractive index and thickness of the film coated on sodalime-silicate glass were investigated.

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.45-50
• /
• 1995

In order to densify LAS(Lithuim Aluminosilicate)system compounds, we used metal alkoxides as precursors. Also Mg was added by sol-gel method using metal alkoxides to the LAS system for improving the sinterability, thermal and mechanical properties. The result was that the synthesizing temperature was lowered about 10$0^{\circ}C$, the sintering temperature was lowered by over 10$0^{\circ}C$ and MOR of samples from metal alkoxides was two times larger than that of sample form oxide.

• Journal of the Korean Ceramic Society
• /
• v.33 no.10
• /
• pp.1147-1155
• /
• 1996

• Journal of the Korean Ceramic Society
• /
• v.26 no.6
• /
• pp.795-801
• /
• 1989

The polycrystalline mullite fiber was synthesized from various combination of starting materials including metal alkoxides and colloidal sol by the sol-gel process. The best spinnability was observed in the sol which showed shear thinning and hysteresis (i.e., thixotropic flow), indicating that the network structure was broken down as the shear rate increased. The mullite fiber was polycrystalline after firing and characterized by thermal analysis, XRD, FT-IR spectroscopy, rheological measurements, and SEM.

• Macromolecular Research
• /
• v.10 no.3
• /
• pp.174-177
• /
• 2002

Proton-conducting hybrid materials composed of silica and Nafion polymer were prepared from the sol-gel synthesis of silica in aqueous Nafion solution. The compositions of hybrid proton conductors were adjusted with the changing ratios of tetraethyl orthosilicate to Nafion. The thermal analysis, FTIR, SEM, and X-ray diffraction studies have proved the formation of Nafion/silica hybrid materials and no remarkable phase separation was observed, which led to an assumption that the macromolecular chain of silica and Nafion was homogeneously interlaned.

• Journal of the Korean Ceramic Society
• /
• v.15 no.4
• /
• pp.205-212
• /
• 1978

The hydration reaction of the slag-gypsum system was studied by X-ray diffraction, differential thermal analysis, optical icroscopic observation, and measurement of heat liberation of hydration. 1. Domestic granulated slag was almost noncrystalized state, and its mineral compositions calculated were 46.53% of gehlenite, 28.14% of akermanite, and 19.04% of wollastonite. 2. The slag quenched with water at relatively high temperature had better reactivity. 3. The production of ettringite, CSH gel and AH3 gel were stimulated by effect of $Ca(OH)_2$, $Mg(OH)_2$ and calcined dolomite as activators, and the strength of hardened body would be developed by forming compacted microstructure.