• Carbon letters
• /
• v.15 no.3
• /
• pp.198-202
• /
• 2014

Amorphous agglomerates of carbon nanospheres (CNS) with a diameter range of 10-50 nm were synthesized using the solution combustion method. High-resolution transmission electron microscopy (HRTEM) revealed a densely packed high surface area of $SP^2$-hybridized carbon; however, there were no crystalline structural components, as can be seen from the scanning electron microscopy, HRTEM, X-ray diffraction, Raman spectroscopy, and thermal gravimetric analyses. Electrochemical and thermo catalytic decomposition study results show that the material can be used as a potential electrode candidate for the fabrication of energy storage devices and also for the production of free hydrogen if such devices are used in a fluidized bed reactor loaded with the as-prepared CNS as the catalyst bed.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.6
• /
• pp.612-618
• /
• 1997

$LiMn_2O_4$ powders were prepared by burning and subsequent calcination of PEG-metal nitrate precursor. After the burning stage of the precursor, some minor phases such as $Mn_2O_3$ (or $Mn_3O_4$), MnO, and carbonate were formed and single phases of $LiMn_2O_4$ were obtained by further calcinations above 400 ℃. From thermal analysis of the precursor, a violent thermal decomposition, which was indicated by a drastic weight loss accompanied by a sharp and strong exothermic peak, was observed and probably caused by an oxidation-reduction reaction between oxidizer and fuel. The formation of the minor phases could be explained in terms of the burning behavior of the precursor by employing valence concepts of propellant chemistry. The calcined powders were composed of submicron-sized but highly agglomerated particles and showed very broad particle size distribution.

• 한국연소학회:학술대회논문집
• /
• 2001.11a
• /
• pp.169-178
• /
• 2001

Among the recent research ideas to reduce hydrocarbon emissions emitted from SI engines till light-off of catalyst since cold start are those exploiting non-thermal plasma technique and photo-catalyst that draws recent attention by virtue of its successful application to practical use to clean up the atmosphere using the feature of its relative independence on temperature. Based on the previous research results obtained with model exhaust gases using an experimental emissions reduction system that utilizes the non-thermal plasma and photo-catalyst technique, further investigation was conducted on a production N/A 1.5 liter DOHC engine during cold start to warm-up. For the effects of non-thermal plasma-photocatalyst combined reactor, 10% concentration reduction was achieved with the fuel component paraffins, and the large increase in non-fuel paraffinic components and acetylene concentrations were similar to those of base condition. However the absolute value was locally a bit higher than those of base condition since the products was made from the dissociation and decomposition of highly branched paraffins by plasma-photocatalyst reactor. Olefinic components were highly decomposed by about 75%, due to these excellent decompositions of olefins which have relatively high MIR values, and the SR value was 1.87 that is 30% reduction from that of base condition, then, the photochemical reactivity was lowered.

• Fire Science and Engineering
• /
• v.13 no.1
• /
• pp.3-10
• /
• 1999

We had investigated combustion properties of natural textile dusts. Decomposition properles of natural textile dusts scavenged by precipitator of spinning factoη were investigated using D DSC(Differential Scanning Calorimeter) and TGA(Thermogravimetric Analysis) by temperature c changes. Combustion pro야rties of natural textile according to size distribution and amount were c checked as temperature variation according to time using spontan$\infty$us ignition apparatus. M Moreover, combustion properties with blowing or without blowing condition were checked in order to investigate combustion prope$\pi$ies in spontaneous ignition apparatus according to flow c condition of air. As results of thermal analyses, increase in r머sing tern야:rature causes initial smold벼ng t temperature to move towards low temperature section 뻐d i띠디떠 smoldering temperature was d de$\sigma$eased more remarkably in atmosphere than in inert gas and that condition allowed heating v value to increase considerably. In addition, as amount and size distribution of natural textile d dusts were increased, i띠ti머 smoldering temperature was lowered. All of combustion forms were s smoldering combustion. Initial smold밍ing temperature was low more slightly with blowing c condition than without blowing condition in sp$\alpha$ltaneoUS ignition apparatus, which condition m made heatim;!; value high.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.1
• /
• pp.42-51
• /
• 2013

In this study, oil palm biomass such as empty fruit bunch (EFB) and palm kernel shell (PKS) was used as raw materials for making pellets. Hardwood sawdusts were also mixed with EFB and PKS for making pellets. For improving a bad forming behavior in a pelletizer, 1 to 3 per cent of corn starch based on oven-dried weight biomass was added. The starch contributed to the decrease of dust generation in addition to the improvement of forming capability during pellet forming. Heating values of every pellets made of EFB and PKS were higher than 4,300 kcal/kg for the first grade pellet, irrespective of addition of sawdusts. However, the pellets made of EFB and PKS had ash contents over 3 per cent, which made it impossible to be applied for home use. Instead, they could be applied for industrial use. For studying their combustion characteristics, the pellets from the mixtures of EFB, PKS and sawdusts were analyzed using thermal gravimetric analyzer (TGA). From the TGA results, thermal decomposition of EFB and PKS occurred following three including endothermic reaction and dehydration, devolatilization of the major chemical components, and finally combustion of residual lignin and char.

• Journal of the Korean Institute of Gas
• /
• v.15 no.4
• /
• pp.7-14
• /
• 2011

Using 20 L spherical explosion vessel and differential scanning calorimeter (DSC), an experimental investigation was carried on explosion characteristics and thermal decomposition of some reactive organic dust. As the result, the minimum explosion concentration of Benzoyl peroxide (BPO), Phthalic anhydride (PA) and 1-Hydroxybenzotriazol (HBT) exist between 10 and 15 g/$m^3$, which indicates that their explosion sensitivity are high. The maximum Kst values of HBT, PA and 97 % BPO are 251, 146 and 80 [$bar{\cdot}m/s$], respectively and the explosion severity of HBT is the explosion class of St-2. The flame velocity was also calculated from the combustion time of dust and flame arrival time to estimate the flame propagation characteristics in a closed vessel. The decomposition temperature and heat of decomposition reaction for 97 % BPO and HBT are $107^{\circ}C$ (1025 J/g), $214^{\circ}C$ (1666 J/g), respectively and it was found that these low decomposition temperature and high released heat affect the explosion characteristics.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.478-485
• /
• 2015

The aim of this study is to analyze the combustion and thermal properties in order to establish baseline data for the fire safety evaluation of domestic timbers. The combustion properties such as heat release rate, total heat release, gas yield, and mass loss were analyzed by the method of cone calorimeter test and thermogravimetry (TGA). Thermal decomposition temperatures of the specimens by TGA were recorded as $359.83^{\circ}C$ for White pine, $359.80^{\circ}C$ for Red-Leaved Hornbeam, $363.14^{\circ}C$ for Carolina poplar, $358.59^{\circ}C$ for Konara oak, and $362.11^{\circ}C$ Sargent cherry. Red-Leaved Hornbeam showed the highest value of heat release rate, but, Carolina poplar wood showed the lowest value. In case of the total heat release, Red-Leaved Hornbeam wood showed the highest value and Carolina poplar wood showed the lowest one. The gas analysis results showed that Sargent cherry wood had the lowest value of 0.021, and Konara oak had the highest at 0.031 in the $CO/CO_2$. The minimum value of mass reduction was recorded as 87.57% for Sargent cherry, but, on the other hand, it was 95.03% for Konara oak. There was a correlation between the gas generation of CO and $CO_2$, and combustion behavior of woods. These results are expected to be usful for providing a fundamental guideline with the fire safety of wood use in interior applications.

• Journal of environmental and Sanitary engineering
• /
• v.11 no.1
• /
• pp.57-61
• /
• 1996

This study was to decompose carbon tetrachloride and CFC with pyrolytic incineration unit because of prohibition of their usage sooner or later. We have investigated heating value and temperature versus decomposing rate, removal of $Cl_2$ and dust in the flue gas, The results obtained were as follows; 1. In combustion condition to decompose $CCl_4$ heating value was 3,300Kcal/Kg, retention time was 2,0 sec. incinerator exit temperature was $950^{\circ}C$. 2.The removal of HCI and $Cl_2$ in flue gas used NaOH as reagent, then molar ratio o of $Na^+/Cl^-$ was 1.07. 3. NaCI of dust component was more than 90 %, 2 stage venturi scrubber was used to remove dust, then removal rate of dust was 99% over at L/G of $1.7Vm^3$

• Textile Coloration and Finishing
• /
• v.20 no.4
• /
• pp.31-42
• /
• 2008

Tricrecyl phosphate(TCP)-containing polyurea microcapsules were prepared by interfacial polymerization using aromatic 2,4-toluene diisocyanate(TDI) and ethylenediamine(EDA) as wall forming materials. The effects of the protective colloids of polyvinylalcohol(PVA) and gelatin were investigated through experimentation. The mean size of prepared polyurea microcapsules was smaller and the surface morphology of the microcapsule prepared by the PVA as protective colloid was much smoother than the gelatin. As the concentration of protective colloid increased, the wall membrane of the polyurea microcapsules became more stable, the thermal stability of the wall membrane increased, the mean particle size became smaller, and the particle distribution was more uniform. PET containg microTCPs have a higher activation energy of decomposition, higher char content and lower heat of combustion.

• Journal of the Korean institute of surface engineering
• /
• v.26 no.5
• /
• pp.255-262
• /
• 1993

Major parameters determining the extent of Ca utilization were investigated for their calcination/sulfation behavior of limestone in the AFBC(Atmospheric Fluidized Bed Combustion) environments. Three different particle sizes of Fredonia limestone were investigated in the lab-scale tubular reactor. The results of the calcination codnversion of limestone imply that thesd decomposition rate of CaCO3 into CaO is dependent on the amount of heat which limestone absorbed. Hg porosimeter measurement of calcined limestone illustrated that surface area and pore volume are increased with decreasing particle size. Raw Fredonia limestone and sequentially as well as simultaneously calcined/sulfated limestones were also examined using SEM. The SEM Studied showed that the surface of the calcined limestone particles is more diffusive nature than that of the parent calcite. However, the sulfur distribution pattern of simultaneously-treated particles and that of the se-quentially-treated one shows no difference.