• Journal of Sericultural and Entomological Science
• /
• v.45 no.1
• /
• pp.34-45
• /
• 2003

Silk was treated with calcium hydroxide for degumming at different treatment times, temperatures and Ca(OH)$_2$ concentration to optimize degumming conditions in this thesis. After degumming, soluble and insoluble sericin were seperated and then the soluble sericin was characterized by measuring the average degree of polymerization (D.P.), lysinoalanine (LAL) content, DSC, and by amino acid analysis. And degummed silk fibroin was characterized by measuring tenacity and SEM. Degumming loss was increased by increasing the treatment time and temperature until about 30 minutes. After then, a slight difference was found along with treatment times at the Ca(OH)$_2$ concentrations of 0.07% and 0.1% solutions. After degumming, insoluble sericin ratio on degumming solution was increased by increasing treatment temperature at Ca(OH)$_2$ 0.04% solution. At the concentration Ca(OH)$_2$ of 0.07%, a soluble ratio was almost 100% regardless of treatment time and temperature. At the beginning of treatment, insoluble ratio was high at Ca(OH)$_2$ 0.1% solution but it was decreased by increasing treatment time. At the Ca(OH)$_2$ concentration of 0.04%, D.P. of soluble sericin was maintained as a constant value of 10 at 100$^{\circ}C$ although treatment time was increased. However, at 80$^{\circ}C$ and 90$^{\circ}C$, it was hard to prepare a soluble sericin having a constant D.P. by increasing treatment time. At the Ca(OH)$_2$ concentration of 0.07%, D.P. was almost 10 irrespective of treatment temperature and time. Soluble sericins with high D.P. of 20∼30 were obtained at 0.1% and 100$^{\circ}C$. LAL was not detected in soluble sericin. As the results of amino acid analysis, it showed that Ca(OH)$_2$ degumming reduced the contents of hydroxy amino acids like Ser., Thr. and Tyr. In DSC analysis of soluble sericin, endothermic peak by thermal deformation and pyrolysis showed at 189$^{\circ}C$ and at 299$^{\circ}C$, respectively. The tenacities of degummed silk were 15∼30% lower than that of raw silk. And it was decreased with increasing treatment time. From the morphological study, the thickness of degummed silk fibroin became thinner by increasing degumming loss. The roughness of a silk fibroin surface was appeared as treatment concentration was increased.

• Korean Journal of Environmental Agriculture
• /
• v.11 no.3
• /
• pp.225-234
• /
• 1992

Thermal decomposition was conducted to investigate the influence of the various factors on stability of a new insecticide, [O, O-Diethyl O-(1-phenyl-3-trifluoromethyl-5-pyrazoyl) thiophosphoric acid ester : KH-502], in view of those informations applicable for industrial exploitation. In the thermal decomposition experiment, KH-502 was, after mixing with Fe, Cu and adjustment of moisture and pH conditions, subjected to three temperatures, 25, 50, and $100^{\circ}C$. Results for stability, and degradation pattern of KH-502 from the above experiment can be summarized as follows: 1. Main products of the thermal decomposition when this was conducted in the closed system were identified as following five compounds:O, O, O-Triethylthiophosphoric acid(TEPA), 1-Phenyl-3-trifluoromethyl-5-ethoxypyrazole(PTMEP), 1-Phenyl-2-ethyl-3-trifluoromethyl-5-hydroxypyrazole(PETMHP), O, O-Diethyl O-(1-phenyl-3-trifluoromethyl-5-pyrazoyl)phosphoric acid ester(KH-502 oxo form), O, S-Diethyl O-(1-phenyl-3-trifluoromethyl-5-pyrazoyl)phospho rothiolate(S-ethyl KH-502). However, compounds such as oxo form and S-ethyl KH-502 were not identified when the thermal decomposition was proceeded in the open system. 2. KH-502 was stable at 25 and 50$^{\circ}C$, but it was decomposed at 100$^{\circ}C$ following the first-order kinetics at the early stages of decomposition. 3. Rate constants for the thermal decomposition of KH-502 at 100$^{\circ}C$ were in the orders of Cu powder addition 0.344>Cu plate addition 0.21>moisture addition 0.05>closed system=open system=iron addition=pH 5.5 adjustment 0.04>pH 8.5 adjustment 0.027 day$^{-1}$, representing KH-502 was decomposed fast at Cu powder treatment and slow at pH 8.5 adjustment. 4. Half-life for the thermal decomposition of KH-502 at 100$^{\circ}C$ was in the orders of Cu powder addition 2.02

• The Korean Journal of Food And Nutrition
• /
• v.25 no.4
• /
• pp.1068-1074
• /
• 2012

Ohmic heating uses electric resistance heat which occurs equally and rapidly inside of food when electrical current is flown into. In other study, we researched about soybean protein's characteristic changes by ohmic heating. Nevertheless treated same temperature, denaturation of soybean protein were accelerated by ohmic heating than conventional heating. In this time, we studied thermal property change of potato starch by ohmic heating besides conventional heating. For this purpose, potato starch was heated at same subgelatinization temperature by ohmic and conventional heating. And thermal properties were tested using DSC. Annealing of starch is heat treatment method that heated at 3~4% below the gelatinization point. DSC analysis results of this study, the $T_o$, $T_p$, $T_c$ of potato starch levels were increased, whereas $T_c{\sim}T_o$ was narrowed. This thermal property changes appear similar to annealing's result. It is thought the results shown in this study, because the heating from below the gelatinization point. 6, 12, 24, 72, and 120 hours heating at $55^{\circ}C$ for potato starch, $T_o$, $T_p$, $T_c$ values continue to increased with heating time increase. The gelatinization temperature of raw potato starch was $65.9^{\circ}C$ and the treated starch by conventional heating at $55^{\circ}C$ for 120 hr was $72^{\circ}C$, ohmic was $76^{\circ}C$. The gelatinization range of conventional (72 hr) was $10^{\circ}C$, ohmic was $8^{\circ}C$. In case of 24 hours heating at 45, 50, 55, 60, $65^{\circ}C$ for potato starch, the result was similar to before. $T_o$, $T_p$, $T_c$ values continue to increased and gelatinization range narrowed with heating temperature increase. In case of conventional heating at $60^{\circ}C$, the results of gelatinization temperature and range were $70.1^{\circ}C$ and $9.1^{\circ}C$. And ohmic were $74.4^{\circ}C$ and $7.5^{\circ}C$. When viewed through the results of the above, the internal structure of starch heated by ohmic heating was found that the shift to a more stable form and to increase the homology of the starch internal structure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.2
• /
• pp.200-205
• /
• 2010

Heat-resistance of W/$Y_2O_3$ as throat insert material was evaluated to develop rocket motor keeping thrust uniformly under condition of high-temperature, high-pressure and long-burn time. Test was conducted with varying burn time, and test results were compared with CIT. Test showed that ablation rate was decreased according as burn time was increased, and that ablation rate of W/$Y_2O_3$ was about 55 % of CIT. Macro/micro structures of throat insert did not show a peculiar phenomenon by increased burn time. In addition, the vacuum heat treatment is effective for the prevention of crack in throat insert.

• Journal of the Korean Ceramic Society
• /
• v.20 no.4
• /
• pp.333-339
• /
• 1983

Semiconducting glaxe of iron system for the recent use as high Voltage porcelain insulators often showed the tendancy of unstable thermal properties. Thus the development of frit including magnetite was studied to cover the defect. In the experimental process melted and quenched frits were ground pelletized and heat-treated at various temperatures in the range of 800-1 $300^{\circ}C$ for various soaking time within 4 hours and then crystallized specimens were obtained. The speciment were studied with optical and electron microscope DTA x-ray diffractometer and electrometer The results obtained were as follows : 1) The optimum condition for the crystal growth of magnetite in the frite was the heat-treatment of $1300^{\circ}C$ for 3hrs and in this case the range of crystal size was $10-11\mu\textrm{m}$ 2) The activation energy for the crystal growth of magnetite was 21.1 kcal/mole. 3) The heat-treament at $1, 250^{\circ}C$ and $1, 300^{\circ}C$ resulted in the good thermal stability and the range of surface resistivity was $3.5{\times}10^4-4.0{\times}10^7$, /TEX> $\Omega$/$cm^2$ which was adguate to semiconducting frit. 4) The conduction mechanism seems to be due to the electron mobility rather than ion mobility and the activa-tion energy for the conduction was 0.07-0.15eV/mole for the heat-treated specimes in the range of 1, 250-1, 300C

• Food Engineering Progress
• /
• v.15 no.4
• /
• pp.398-403
• /
• 2011

A dielectric barrier discharge plasma (DBDP) treatment system was fabricated and the optimum operating conditions for the plasma generation were determined in order to explore the potential of cold plasma as a non-thermal proessing technology. The microbial inactivation performance of the system was also evaluated against Staphyloocus aureus. The system consisted of power supply, transformer, electrode assembly and sample treatment plate. The input power was 220 V single phase AC and amplified to 10.0-50.0 kV on a transformer. A pulsed sine wave of frequency 10.0-50.0 kHz was introduced to the electrode embedded in ceramic as a dielectric barrier material in order to generate plasma at atmospheric pressure. Higher currents and consequently greater power were required for the plasma generation as the frequencies increased. A homogeneous and stable plasma was generated at currents of 1.0-2.0, and frequencies of 32.0-35.3 kHz. The optimum electrode-gaps for the plasma generation were 1.85 mm without loaded samples. More power was consumed as the electrode-gaps increased. The practically optimum electrode- gap was, however, 2.65 mm when samples were treated on slide-glasses for microbial inactivation. The maximum temperature increase after 10 min treatment was less than 20$^{\circ}C$, indicating no microbial inactivation effect by heat and thereby insuring a non-thermal method. The DBDP inactivation effect against Staphyloocus aureus increased linearly with treatment time up to 5 min, but plateaued afterward. More than 5 log reduction was achieved by 10 min treatment at 1.25 A.

• Nuclear Engineering and Technology
• /
• v.48 no.3
• /
• pp.684-701
• /
• 2016

The Gaussian process model (GPM) is a flexible surrogate model that can be used for nonparametric regression for multivariate problems. A unique feature of the GPM is that a prediction variance is automatically provided with the regression function. In this paper, we estimate the safety margin of a nuclear power plant by performing regression on the output of best-estimate simulations of a large-break loss-of-coolant accident with sampling of safety system configuration, sequence timing, technical specifications, and thermal hydraulic parameter uncertainties. The key aspect of our approach is that the GPM regression is only performed on the dominant input variables, the safety injection flow rate and the delay time for AC powered pumps to start representing sequence timing uncertainty, providing a predictive model for the peak clad temperature during a reflood phase. Other uncertainties are interpreted as contributors to the measurement noise of the code output and are implicitly treated in the GPM in the noise variance term, providing local uncertainty bounds for the peak clad temperature. We discuss the applicability of the foregoing method to reduce the use of conservative assumptions in best estimate plus uncertainty (BEPU) and Level 1 probabilistic safety assessment (PSA) success criteria definitions while dealing with a large number of uncertainties.

• Journal of Soil and Groundwater Environment
• /
• v.17 no.2
• /
• pp.7-14
• /
• 2012

Batch tests were carried out to evaluate the thermal treatment of low volatile organic compounds in low-permeability soil. The chemical oxidation by sodium persulfate catalyzed by heat and Fe (II) was evaluated. Enhanced persulfate oxidation of n-decane (C-10), n-dodecane (C-12), n-tetradecane (C-14), n-hexadecane (C-16), and phenanthrene was observed with thermal catalyst, indicating increased sulfate radical production. Slight enhancement of the pollutants oxidation was observed when initial sodium persulfate concentration increased from 5 to 50 g/L. However, the removal efficiency greatly decreased as soil/water ratio increased. It indicates that mass transfer of the pollutants as well as the contact between the pollutants and sulfate radical were inhibited in the presence of solids. In addition, more pollutants can be adsorbed on soil particles and soil oxidant demand increased when soil/water ratio becomes higher. The oxidation of the pollutants was significantly improved when catalyzed by Fe(II). The sodium persulfate consumption increased at the same time because the residual Fe(II) acts as the sulfate radical scavenger.

• Journal of Powder Materials
• /
• v.23 no.3
• /
• pp.202-206
• /
• 2016

A Ni-Ti-B alloy powder prepared by mechanical alloying (MA) of individual Ni, Ti, and B components is examined with the aim of elucidating the phase transitions and crystallization during heat treatment. Ti and B atoms penetrating into the Ni lattice result in a Ni (Ti, B) solid solution and an amorphous phase. Differential thermal analysis (DTA) reveals peaks related to the decomposition of the metastable Ni (Ti, B) solid solution and the separation of equilibrium $Ni_3Ti$, $TiB_2$, and ${\tau}-Ni_20Ti_3B_6$ phases. The exothermal effects in the DTA curves move to lower temperatures with increasing milling time. The formation of a $TiB_2$ phase by annealing indicates that the mechanochemical reaction of the Ni-Ti-B alloy does not comply with the alloy composition in the ternary phase diagram, and Ti-B bonds are found to be more preferable than Ni-B bonds.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.110-116
• /
• 2002

At elevated temperature, very complex precipitations occur in STS316. To investigate the effect of the precipitation on mechanical properties in SIS316, tensile tests and fatigue crack growth tests were carried out at $650^{\circ}C$ using artificially degraded materials. The material degradation was simulated by aging for up to 20000 hrs. at $750^{\circ}C$, which is equal to 179000hrs (about 20yrs) of service life at $650^{\circ}C$, after conducting solution treatment for 20 min. at $11300^{\circ}C$. The result of the hardness test and the tensile test showed that both properties are closely related to the mean free distance of carbides. Also, from the results of fracture tests at $650^{\circ}C$, ${\triangle}K_{th}$, after values were found to decrease as aging time and microstructure, as the volume fraction of $\sigma$ phase increased.