• Polymer(Korea)
• /
• v.34 no.5
• /
• pp.424-429
• /
• 2010

The hybrid composites of aliphatic polyester-silica were prepared via a sol-gel reaction and their potential application using as a buffer coating layer in the thermoelectric device were investigated. When aliphatic polyesters were thermally treated at a high temperature of $240^{\circ}C$, the polymer showed an increases in thermal degradation temperature by $30{\sim}90^{\circ}C$ according to the thermal treatment time. The polyester-silica composites showed an increases in thermal degradation temperature by $30{\sim}50^{\circ}C$ according to the content of the added silica. Polyester-silica composite showed neither discoloration nor change in optical properties because Knoevenagel condensation reaction was hindered by silica structure. The thermal conductivity of the composites increased linearly according to the content of added silica.

• Journal of the Korean Society of Physical Medicine
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2009

Purpose : The purpose of this study was to evaluate the effects of cold therapy and thermal therapy, and immunoreactivity of vascular endothelial growth factor(VEGF), Interleukin-1(IL-1) and Interleukin-6(IL-6) on angiogenesis after muscle contusion injury. Methods : Muscle contusion injury was induced in the gastronemius muscle by dropping a metal bead(22.8g). Cold and thermal theraphy was applied immediately and directly to the skin of injured muscle daily for three days. (experimental group-1 : $5^{\circ}$ cold pack, experimental group-2 : $50^{\circ}$ hot pack, control group non applied, treatment time : 10minutes) Results : The experimental group-1 and 2 showed higher immunoreactivity of VEGF, IL-1, IL-6 than control group during 3 days(P<0.05). And the experimental group-2 showed higher than the experimental group-1 especially VEGF(P<0.05). Conclusion : There data thermal therapy was more effective than cold therapy in the acute muscle contusion injury.

• Journal of the Korean Society of Combustion
• /
• v.12 no.3
• /
• pp.24-32
• /
• 2007

A theoretical model was developed for rotary kiln and computational study was conducted to find the effect of feeding characteristics. One dimensional model with the variations of heating distribution, length of heating zone, excess air ratio and revolution was considered. The comparison of parallel-flow rotary kiln with that of counter-flow was conducted. For parallel-flow type, it is found that the variation of temperature of solid is not great for the zone that is following flame-heating zone. This zone is good to take the special treatment because thermal deviation is small and contacting time is enough for another treatment. Increase of excess air ratio have the effect of decreasing solid temperature. But this effect of decreasing solid temperature goes small for the great excess air ratio. The heating is efficient for the flame which has the maximum heating at the central region of the full length.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.126-131
• /
• 2005

To increase the efficiency of an applicator during microwave hyperthermia therapy, first, the length from the antenna end to a slot is varied to get the optimal matching of the characteristic impedance at the frequency of 2.45 GHz. Using the electric and thermal constants of biological tissue, we compose a phantom to calculate temperature increment as well as the resonance characteristics and the SAR distributions. The proposed 3-slot sleeve antenna inserted in an applicator plays an effective role in increasing the therapy size in the view of heating performance as electromagnetic energy tends to concentrate on not feed point direction but treatment area. The SAR is then used in combination with a finite difference heat transfer equation to determine the temperature distribution. Also, in order to shorten treatment time and increase therapy size, a square-array structure is suggested and analyzed.

• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.1
• /
• pp.49-60
• /
• 2002

Welding is essential in ship production since welding is very popular method for joining two or more metals. However, welding causes residual stress and distortion and these give a bad influence to the structure strength and assembly of ship blocks. Therefore, prediction and treatment of residual stress and distortion is a key to accuracy control in shipyard. In this paper, a computational procedure, based on thermal-elastic-plastic 3-dimensional FEA, has been suggested to simulate butt and fillet welding process. In the simulation process, temperature distribution at each time step is obtained by heat transfer analysis and then thermal deformation analysis is done with obtained temperature distributions to find the residual stress and distortion. In heat transfer analysis, enthalpy method is used to realize phase change at melting temperature. Also element birth and death method is used to simulate adding of weld metal in both heat transfer analysis and thermal elastic plastic analysis. The proposed procedure is verified by related researches and the results show good agreement with those of related researches.

• Environmental Engineering Research
• /
• v.23 no.3
• /
• pp.282-287
• /
• 2018

Three different methods of bacterial viability monitoring were compared to detect chemically or thermally inactivated Escherichia coli. Direct colony enumeration, live/dead bacterial cell staining with a fluorescent dye, and the dehydrogenase activity assay were compared with respect to their ease of use and time required to perform the three different tests. The green (live cell)/red (dead cell) ratio obtained from the fluorescent bacterial cell staining approach showed a linear relationship with the colony forming units; the result obtained with dehydrogenase was similar to those. The sensitivity of the monitoring methods to detect bacterial deactivation varied with different disinfection conditions. After thermal treatment, the sensitivity of the staining approach was lower, while that of the dehydrogenase activity assay was the highest. After chemical treatment, the sensitivity of detection for both methods was similar.

• Journal of Microbiology and Biotechnology
• /
• v.17 no.3
• /
• pp.524-529
• /
• 2007

Pressure inactivation behavior of Bacillus amyloliquefaciens spores was investigated in deionized water. The spores of B. amyloliquefaciens were subjected to $105^{\circ}C$ and 700 MPa. The magnitude of the decrease in viability after pressure treatment was similar to that after pressure treatment followed by heat shock. The increase of dipicolinic acid (DPA) release was correlated with the spore inactivation, and the hydrophobicity did not significantly change during the pressure-assisted thermal processing (PATP). Lag phase duration increased with increasing pressure process time. The mechanisms of spore germination and inactivation during the PATP were related to a complex physiological process.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.7
• /
• pp.759-766
• /
• 1988

the effect of heat treatment in oxygen ambient on the nucleation and growth of oxidation induced stacking faults(OSF) in n-type(100)silicon wafer has been investigated. The growth of OSF is determind as a function of oxygen concentration in silicon wafer, heat treatment time and temperature, and the activation energy for the growth of OSF can be obtained from the growth kinetics. The activation energies are respectively 2.66 eV for dry oxidation and 2.37 eV for wet oxidation. In this paper, we have also studied the structural feature of OSF with the comparison of optical microscopic morphology and crystalline structure.

• Journal of Adhesion and Interface
• /
• v.7 no.1
• /
• pp.16-22
• /
• 2006

In this work, the effect of cure temperature and time on the thermal stability and the exothermic cure reaction peak of a waterborne resol-type phenol-formaldehyde resin, which may be used for preparing phenolic sheet molding compounds (SMC), has been investigated using a thermogravimetric analyzer and a differential scanning calorimeter. The weight loss of waterborne phenol-formaldehyde resin was mainly occurred at three temperature stages: near $200^{\circ}C,\;400^{\circ}C$, and $500^{\circ}C$. The carbon yield at $750^{\circ}C$ for the cured resin was about 62%~65%. Their thermal stability increased with increasing cure temperature and time. Upon cure, the exothermic reaction was taken placed in the range of $120^{\circ}C{\sim}190^{\circ}C$ and the maximum peak was found in between $165^{\circ}C$ and $170^{\circ}C$. The shape and the maximum of the exothermic curves depended on the given cure temperature and time. To remove $H_2O$ and volatile components, the uncured resin needed a heat-treatment at $100^{\circ}C$ for 60 min at least prior to cure or molding. Curing at $130^{\circ}C$ for 120 min made the exothermic peak of waterborne phenol-formaldehyde resin completely disappeared. And, post-curing at $180^{\circ}C$ for 60 min further improved the thermal stability of the cured resin.

• Journal of Environmental Science International
• /
• v.13 no.4
• /
• pp.403-412
• /
• 2004

Waste water-soluble cutting oil was treated with WI type #1 and WI type #2. The properties of the original water-soluble cutting oil were pH=l0.4, viscosity=1.4cP, CODcr=44,750 ppm, and TOC=10,569 ppm. However, the properties of the oil used for more than 3 months were changed to pH=7.82, viscosity=2.1cP, CODcr=151,000 ppm, and TOC=74,556 ppm. It might be attributed to the fact that molecular chains were cut due to thermal oxidation and impurities such as metal chips were incorporated in to the oil during the operation processes. To prevent the putrefaction of oil, the sterilization effect of ozone and UV on the microorganism in the oil was investigated. Ozone treatment showed that 99.99% of the microorganism was annihilated with 30 minutes contact time and 60 minutes were necessary for the same effect when UV was used. Ozone treatment could cut molecular chains of the oil due to strong sterilization power, which was evidenced by the increase of TOC from 25,132 ppm at instantaneous contact to 28,888 ppm at 30 minutes contact time. However, UV treatment didn't show severe changes in TOC values and thus, seemed to cause of severe cut of molecular chains. When the activated carbon was used to treat the waste water-soluble cutting oil, TOC decreased to 25,417 ppm with 0.lg carbon and to 15,946 ppm with 5.0g carbon. This results indicated that the waste oil of small molecular chains could be eliminated by adsorption. From the results, it could be concluded that these treatment techniques could be proposed to remove the waste oil of small molecular chains resulting in the degradation of the oil properties. In addition, these experimental results could be used for the correlation with future works such as investigation of the molecular distribution according to the sizes, lengths, and molecular weight of the chains.