• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.670-677
• /
• 2016

Laboratory and meta-analyses were done for 9% NI Steel for use in a liquefied natural gas carrier. The meta-analysis is based on a previous study. The laboratory analysis examines the effects of a single pass and multiple passes on the tensile strength through an impulse-response test. The tensile strength increased from pass one to pass three and decreased from pass four to pass ten. The pass and multi-pass welding had a positive effect on the tensile strength. Lastly, the welding and tensile time had a positive effect on the tensile strength.

• Journal of Soil and Groundwater Environment
• /
• v.21 no.3
• /
• pp.64-81
• /
• 2016

To analyze the influence of various groundwater flow rates (specific discharge) on BHE system with balanced and unbalanced energy loads under assuming same initial temperature (15℃) of ground and groundwater, numerical modeling using FEFLOW was used for this study. When groundwater flow is increased from 1 × 10⁻⁷ to 4 × 10⁻⁷m/s under balanced energy load, the performance of BHE system is improved about 26.7% in summer and 22.7% at winter time in a single BHE case as well as about 12.0~18.6% in summer and 7.6~8.7% in winter time depending on the number of boreholes in the grid, their array type, and bore hole separation in multiple BHE system case. In other words, the performance of BHE system is improved due to lower avT in summer and higher avT in winter time when groundwater flow becomes larger. On the contrary it is decreased owing to higher avT in summer and lower avT in winter time when the numbers of BHEs in an array are increased, Geothermal plume created at down-gradient area by groundwater flow is relatively small in balanced load condition while quite large in unbalanced load condition. Groundwater flow enhances in general the thermal efficiency by transferring heat away from the BHEs. Therefore it is highly required to obtain and to use adequate informations on hydrogeologic characterristics (K, S, hydraulic gradient, seasonal variation of groundwater temperature and water level) along with integrating groundwater flow and also hydrogeothermal properties (thermal conductivity, seasonal variation of ground temperatures etc.) of the relevant area for achieving the optimal design of BHE system.

• The Korean Journal of Nuclear Medicine
• /
• v.34 no.4
• /
• pp.265-275
• /
• 2000

The thyroid gland is an interesting endocrine organ where a spectrum of tumors with different behavior arise. At one end of spectrum there is differentiated thyroid carcinoma (DTC) with excellent prognosis, whereas at the other end of the spectrum is anaplastic thyroid cancer which has universally poor outcome. Radioiodine (I-131) therapy has been in use for the treatment of thyroid diseases since 1946. It was introduced by Seidlin et al. 1) Although the use of I-131 has been vouge for a long time, its use in therapy for well differentiated thyroid cancer is still controversial 2). This is because, thyroid cancers (TC) are generally slow growing tumors, with low mortality and normal spans of survival. To record recurrence and mortality, long term follow up studies over a period of two to three decades are needed to establish definite conclusions on the acceptable mode of treatment The incidence of the disease being very low a large number of cases needed to establish a meaningful statistical data is lacking as most published reports feat with small series. Here again in the problem encountered are the differing protocols for treatment with I-131, the indications for treatment which may include or exclude ablation of residual thyroid tissue, cervical nodal and distal metastases. The dosage of I-131 used for ablation of residual thyroid tissue and metastatic disease also vary. The most reliable conclusion regarding I-131 treatment are obtained from studies reported on a large series of patients followed over a period of 2 decades or more from a single institute with a more or less unchanged protocol of management.

• The Journal of the Korea Contents Association
• /
• v.10 no.10
• /
• pp.26-35
• /
• 2010

Recently, multi client PC technologies that several users can use one set of computer at the same time are being designed to use the surplus computer resource. In general, as the existing PC management system considers only a single client PC that only one user uses a computer, various kinds of complicated problems may be arisen. This paper designs and realizes a remote management system that can monitor and control the information used in the windows based OS multi-client using WMI technology. The proposed system herein uses WMI technology and newly defined client management protocol and provides the monitoring and control functions on individual resource use information of multi-client. As well, it provides a communication function between the server and the client, and locking setting and access control functions.

• Journal of Digital Contents Society
• /
• v.16 no.4
• /
• pp.545-553
• /
• 2015

While all of the data has a value in itself, most of the data that is collected in the real world is a random and unstructured. In order to extract useful information from the data, it is need to use the data transform and analysis algorithms. Data mining is used for this purpose. Today, there is not only need for a variety of data mining techniques to analyze the data but also need for a computational requirements and rapid analysis time for huge volume of data. The method commonly used to store huge volume of data is to use the hadoop. A method for analyzing data in hadoop is to use the MapReduce framework. In this paper, we developed a tournament-based MapReduce method for high efficiency in developing an algorithm on a single machine to the MapReduce framework. This proposed method can apply many analysis algorithms and we showed the usefulness of proposed tournament based method to apply frequently used data mining algorithms k-means and k-nearest neighbor classification.

• Restorative Dentistry and Endodontics
• /
• v.37 no.1
• /
• pp.9-15
• /
• 2012

Objectives: This study evaluated the effect of 2% chlorhexidine digluconate (CHX) with different application times on microtensile bonds strength (MTBS) to dentin in class I cavities and intended to search for ideal application time for a simplified bonding protocol. Materials and Methods: Flat dentinal surfaces with class I cavities ($4mm{\times}4mm{\times}2mm$) in 40 molar teeth were bonded with etch-and-rinse adhesive system, Adper Single Bond 2 (3M ESPE) after: (1) etching only as a control group; (2) etching + CHX 5 sec + rinsing; (3) etching + CHX 15 sec + rinsing; (4) etching + CHX 30 sec + rinsing; and (5) etching + CHX 60 sec + rinsing. Resin composite was builtup with Z-250 (3M ESPE) using a bulk method and polymerized for 40 sec. For each condition, half of the specimens were immediately submitted to MTBS test and the rest of them were assigned to thermocycling of 10,000 cycles between $5^{\circ}C$ and $55^{\circ}C$ before testing. The data were analyzed using two-way ANOVA, at a significance level of 95%. Results: There was no significant difference in bond strength between CHX pretreated group and control group at the immediate testing period. After thermocycling, all groups showed reduced bond strength irrespective of the CHX use. However, groups treated with CHX maintained significantly higher MTBS than control group (p < 0.05). In addition, CHX application time did not have any significant influence on the bond strength among groups treated with CHX. Conclusion: Application of 2% CHX for a short time period (5 sec) after etching with 37% phosphoric acid may be sufficient to preserve dentin bond strength.

• Journal of the Korean Society for information Management
• /
• v.25 no.4
• /
• pp.205-226
• /
• 2008

The success of social networking sites (SNSs) may depend on many factors. Continuance use of SNSs is one of these. Especially, in the Web environment where users can leave one service with a single mouse click, maintaining existing members cost much time and efforts. Without continuance use of SNSs, SNS-based service would not create any value. This study focused on identifying factors influencing users' continuance intention in SNSs. Based on relevant literature review, six influencing factors were initially identified. They were reputation, relational capital, knowledge quality, compatibility, personalization, and satisfaction. Web-based questionnaire survey was conducted and a total of 325 usable responses were collected. Reliability test and two rounds of exploratory factor analyses resulted in identifying five factors. The relationship between the factors and the continuance intention was tested by using multiple regression analyses. The analyses revealed that satisfaction was the most significant factor. Knowledge quality and relational capital also had significant effects while reputation and personalization did not have significant effect on continuance intention. Instead, reputation and personalization showed significance in influencing satisfaction.

• Korean Journal of Clinical Laboratory Science
• /
• v.56 no.2
• /
• pp.105-114
• /
• 2024

Clinical laboratories endeavor to secure quality by establishing effective quality management systems. However, laboratory environments are complex, and single quality control procedures may inadequately detect many errors. Patient-based real-time quality control (PBRTQC) is a laboratory tool that monitors the testing process using algorithms such as Bull's algorithm and several variables, such as average of normal, moving median, moving average, and exponentially weighted moving average. PBRTQC has many advantages over conventional quality control, including low cost, commutability, continuous real-time performance monitoring, and sensitivity to pre-analytical errors. However, PBRTQC is not easily implemented as it requires statistical algorithm selection, the design of appropriate rules and protocols, and performance verification. This review describes the basic concepts, methods, and procedures of PBRTQC and presents guidelines for implementing a patient-based quality management system. Furthermore, we propose the combined use of PBRTQC when the performance of internal quality control is limited. However, clinical evaluations were not conducted during this review, and thus, future evaluation is required.

• Journal of Navigation and Port Research
• /
• v.44 no.3
• /
• pp.145-150
• /
• 2020

The ship motion of large LNG ships affects ships' safety. The purpose of this study was to estimate the transfer function of roll motion among the hull motion of 153,000 m3 class LNG vessels. The ship motion transfer function was modeled using a Linear Time-Invarient system with single input, single output, and transfer function. The transfer function of the ship motion was estimated by the system identification method using single ocean wave as input of the model, and using the roll motion of the LNG ship obtained through ANSYS as the output of the model. The usefulness of the experimental results was evaluated using the precision and estimation rate of the model for cases wherein the different transfer function dimensions. Results of the experiment showed a precision at 99% and 98%, with estimation rate at 78% and 50%. From these results, we found the proposed method of estimating the transfer function of ship motion in this study reasonable. In the future, data of ship motion in actual sea conditions will be acquired and it will be applied to make the construction of models with multiple inputs and multiple outputs for practical use.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.42 no.3
• /
• pp.144-150
• /
• 2016

Objectives: We compared the transbuccal and transoral approaches in the management of mandibular angle fractures. Materials and Methods: Sixty patients with mandibular angle fractures were randomly divided into two equal groups (A, transoral approach; group B, transbuccal approach) who received fracture reduction using a single 2.5 mm 4 holed miniplate with a bar using either of the two approaches. Intraoperatively, the surgical time and the ease of surgical assess for fixation were noted. Patients were followed at 1 week, 3 months, and 6 months postoperatively and evaluated clinically for post-surgical complications like scarring, infection, postoperative occlusal discrepancy, malunion, and non-union. Radiographically, the interpretation of fracture reduction was also performed by studying the fracture gap following reduction using orthopantomogram tracing. The data was tabulated and subjected to statistical analysis. A P -value less than 0.05 was considered significant. Results: No significant difference was seen between the two groups for variables like surgical time and ease of fixation. Radiographic interpretation of fracture reduction revealed statistical significance for group B from points B to D as compared to group A. No cases of malunion/non-union were noted. A single case of hypertrophic scar formation was noted in group B at 6 months postsurgery. Infection was noted in 2 patients in group B compared to 6 patients in group A. There was significantly more occlusal discrepancy in group A compared to group B at 1 week postoperatively, but no long standing discrepancy was noted in either group at the 6 months follow-up. Conclusion: The transbuccal approach was superior to the transoral approach with regard to radiographic reduction of the fracture gap, inconspicuous external scarring, and fewer postoperative complications. We preferred the transbuccal approach due to ease of use, minimal requirement for plate bending, and facilitation of plate placement in the neutral mid-point area of the mandible.