• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.446-451
• /
• 2009

Reliability evaluations of linear low density polyethylene (LLDPE) pipe with respect of thermal exposure time have been investigated in accordance with RS M 0042, which is a reliability standard for polymer pipe. As the thermal exposure time is prolonged, a progressive increase, until 250 days, in tensile strength and a slight increase in hardness are observed, while a proportional decrease in elongation at break is showed. These results can be explained by the increase of crystallinity, followed by the increase of crosslinking density, chain scission and the decrease in chain mobility, due to thermal oxidation as the exposure time increases. Long term hydrostatic pressure test result implies the existence of transition point from ductile to brittle fracture. Oxidation induction time (OIT) test is employed to monitor the thermo-oxidative degradation of LLDPE pipe. This result shows that after the exposure time is 250 days, the depletion of antioxidants added in LLDPE pipe occurs. An empirical equation as function of exposure time, under $100^{\circ}C$ thermal-degradation condition, is proposed to assess the remaining amount of antioxidants owing to thermo-oxidative degradation. Fourier transform infrared spectroscopy results show the increase of carbonyl (-C=O) and hydroxyl (O-H) function groups on the surface of thermally exposed LLDPE pipe. This result suggests that the hydrocarbon groups locally undergo the oxidation on the LLDPE surface due to thermal-degradation.

• Progress in Superconductivity
• /
• v.7 no.1
• /
• pp.97-101
• /
• 2005

Bi-22l2 tubes for fault current limiter (FCL) were fabricated by centrifugal melting process. $SrSO_4$ ($10\;wt.\;\%$) was added to Bi-2212 powder to lower the melting point of Bi-22l2 and to improve the mechanical properties. The BSCCO powder was completely melted at $1300\;^{\circ}C$ using the RF furnace and then poured into rotating steel mold. The steel mold, preheated at $450\;{\circ}C{\sim}550^{\circ}C$ for 2 hour was rotated at $1020{\sim}2520\;RPM$. The solidified BSCCO tube was cooled down to room temperature in the furnace for 48 hours and separated from the mold between Bi-2212 and the mold. $ZrO_2$ solution was used to separate it easily from the mold and Ag tape was attached in the mold inner wall of the mold to analysis electrical property. Bi-22l2 tube was often cracked when the cooling rate was high. BSCCO tubes with $70{\Phi}{\times}100\;mm,\;50{\Phi}{\times}100\;mm$ and $30{\Phi}{\times}150\;mm$ size were fabricated by centrifugal melting process. The $J_{c}s$ of tubes with $50{\Phi}{\times}100\;mm{\times}4.0\;t$ and $50{\Phi}{\times}100\;mm{\times}4.l\;t$ were 178 and $74.2\;A/cm^2$ at 77K, respectively. The processing condition for Bi-2212 tube fabrication was investigated using XRD and SEM analyses.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.2C
• /
• pp.182-192
• /
• 2010

This paper proposes the hardware IP design of JBIG2 encoder. In order to facilitate the next generation FAX after the standardization of JBIG2, major modules of JBIG2 encoder are designed and implemented, such as symbol extraction module, Huffman coder, MMR coder, and MQ coder. ImpulseC Codeveloper and Xilinx ISE/EDK program are used for the synthesis of VHDL code. To minimize the memory usage, 128 lines of input image are processed succesively instead of total image. The synthesized IPs are downloaded to Virtex-4 FX60 FPGA on ML410 development board. The four synthesized IPs utilize 36.7% of total slice of FPGA. Using Active-HDL tool, the generated IPs were verified showing normal operation. Compared with the software operation using microblaze cpu on ML410 board, the synthesized IPs are better in operation time. The improvement ratio of operation time between the synthesized IP and software is 17 times in case of symbol extraction IP, and 10 times in Huffman coder IP. MMR coder IP shows 6 times faster and MQ coder IP shows 2.2 times faster than software only operation. The synthesized H/W IP and S/W module cooperated to succeed in compressing the CCITT standard document.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.27 no.6
• /
• pp.510-522
• /
• 2005

To assess the clinical applicability of bio-artificial mucosa which was made with autologous oral keratinocytes and human acellular dermal matrix, the formation of basement membrane and stratification of oral keratinocytes were evaluated. Six New Zealand white rabbits (around 2kg in weight) were anesthetized and its buccal mucosa was harvested (1.0 $\times$ 0.5cm size). Oral keratinicytes were extracted and cultured primarily with the feeder layer of pretreated NIH J2 3T3 fibroblast. These confluent cells were innoculated on the human acellular dermal matrix and cultured in multiple layer by air-rafting method. After 3, 5, 7, 10, 14 days of culture, each cultured bio-artificial mucosa was investigated the number of epthelial layer of by H&E stain and toluidine blue stain. The immuhohistochemical methods were used to evaluate the cell division capacity, the formation of basement membrane, and it's property of specific cells (PCNA, cytokeratin 14, laminin). Transmission electromicroscopy was used for the attachment between cells and matrix with the number of hemidesmosome. In result, the numbers of layer of stratified growth of oral keratinocyte cultured on the human acellular dermal matrix and the number of hemidesomal attachment between epithelial cells and human acellular dermal matrix were similar to the layers of normal oral mucosa after 10 days of culture. The cell division rate, basement membrane formation and proliferation rate increased as culture period increased. With these results, bio-artificial mucosa with autologous oral epithelial cells cultured on the acellular dermal matrix had clinically adaptable properties after 10 days' culture and this new bio-artificial mucosa model with relatively short culture time can be expected clinical applicability.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.12
• /
• pp.1008-1015
• /
• 2002

The fabricated La-modified lead titanate (PLT) thin film without poling treatment was investigated for modulation frequency dependence of pyroelectric properties by the dynamic method. $Pb_{l-x}La_{x}Ti_{l-x/4}O_3$(x=0.1) (PLT(10)) thin film haying 10 mol% La content was deposited on a Pt/$TiO_{x}$/$SiO_2$/Si substrate by sol-gel method. The PLT(10) thin film exhibits a relatively excellent dielectric property. The pyroelectric coefficient (p) of the PLT(10) thin film is 6.6 x $10^{-9}C$$textrm{cm}^2$$.$K without frequency dependence. The figure of merits for the voltage responsivity and specific detectivity are 1.03 x $10^{-11}C$.cm/J and 1.46 x $10^{-10}C$.cm/J, respectively The PLT(10) thin film has voltage responsivity (RV) of 5.IS V/W at 8 Hz. Noise equivalent power (NEP) and specific detectivity ($D^{*}$) of the PLT(10) thin film are 9.93 x $10^{-8}$W/$Hz^{1/2}$ and 1.81 x $10^{6}$cm.$Hz^{1/2}$/W at the same frequency of 100 Hz,, respectively The results means that PLT thin film having 10 mol% La content is suitable for the sensing materials of pyroelectric IR sensors.

• Korean Journal of Veterinary Research
• /
• v.44 no.1
• /
• pp.15-21
• /
• 2004

This paper describes the development of $^{99m}Tc$ tricarbonyl cysteine as potential renal function diagnostic radiopharmaceutical and evaluation of its biological characteristics using experimental animals. l-Cysteine was labeled efficiently with $^{99m}Tc$ tricarbonyl precursor $([^{99m}Tc(CO)_3(H_2O)_3)]^{+})$ under 30 min heating at ${75^{\circ}C}$. Labeling yield and stability were analyzed by high performance liquid chromatography (HPLC). The biodistribution property of $^{99m}Tc$ tricarbonyl cysteine in mice and its dynamic imaging profiles in rabbits were carried out. To investigate the excretion mechanism of $^{99m}Tc$ tricarbonyl cysteine, tubular transport inhibition test with probenecid was adopted. $^{99m}Tc$ tricarbonyl cysteine was obtained with a high labeling yield under the moderate condition. The results of biodistribution experiments of $^{99m}Tc$ tricarbonyl cysteine in ICR mice at 3 and 90 min provided that $^{99m}Tc$ tricarbonyl cysteine was very highly accumulated in the kidney and bladder, thereby almost 99% of $^{99m}Tc$ tricarbonyl cysteine was excreted within 90 min post injection. The same results were confirmed by the whole body dynamic images for 30 minutes and static images in rabbits at given time intervals after injection. Renogram of $^{99m}Tc$ tricarbonyl cysteine in rabbits showed that its $T_{max}$ and $T_{1/2}$ of $^{99m}Tc$ tricarbonyl cysteine were $2.33{\pm}0.56$ and $4.30{\pm}0.79$ min, respectively. The $T_{max}$ of $^{99m}Tc$ tricarbonyl cysteine with probenecid pretreatment was $2.30{\pm}0.17$ min, whereas $T_{1/2}$ of that with probenecid pretreatment was $17.0{\pm}32.47$ min. $T_{1/2}$ of $^{99m}Tc$ tricarbonyl cysteine with probenecid pretreatment was significantly different, as compared to the result without probenecid (p<0.0001). The results showed that the excretion of $^{99m}Tc$ tricarbonyl cysteine was extremely affected by probenecid. Therefore, $^{99m}Tc$ tricarbonyl cysteine was rapidly excreted from the kidney principally by the tubular secretion.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.1
• /
• pp.37-44
• /
• 1997

The Purpose of this study was to evaluate the effect of cooking methods and reheating on texture characteristics of sausage. Sausage samples were cooked(microwaving, gas-broiling and frying), reheated on day 3 and 6 after refrigeration and put to evaluation of sensory and texture characteristics. The results of sensory evaluation showed that hardness, salty taste, rancid flavor and after-taste were increased but wetness and chewiness were decreased by reheating after refrigeration. Overall acceptability was the highest when the samples were gas broiled and reheated on day 3 after refrigeration. As for the estimation of texture changes by rheometer, hardness, cohesiveness, elasticity, gum-miness and chewiness tended to increase by reheating after refrigeration. Hardness, cohesiveness, gumminess and chewiness were the highest when the samples were gas-broiled and reheated on day 3 after refrigeration.

• Korean Journal of Food Science and Technology
• /
• v.28 no.3
• /
• pp.573-579
• /
• 1996

Crosslinked potato starches (XP), from 2,400 to 1,900 anhydroglucose units per crosslinked (AGU/CL), were prepared by reacting with epichlorohydrin. Some of the physicochemical properties of the XPs were then compared with those of native potato and cowpea starches. Crosslinking decreased moisture, protein and ash contents but had no effect on phosphorus content. Water binding capacities of the XPs increased as the degree of crosslinking increased, and that of the XP with 2,100 AGU/CL approached the value of cowpea starch. The absorption maxima of the starch-iodine complex shifted from 594 to 580 nm. Granule size increased slightly and surface appearance of the granule became rough when crosslinked. Both native and crosslinked potato starches showed B type X-ray diffraction pattern, and the relative crystallinity was not affected by crosslinking. Gelatinization temperature and the heat of gelatinization, measured by differential scanning calorimeter (DSC), did not change within the range of crosslinking tested. From X-ray and DSC data, it was concluded that the crosslinking ocurred in the amorphous region of the starch granule.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.3
• /
• pp.801-812
• /
• 2021

In order to delivery biotin to skin, ethosomes containing both biotin and ceramide were researched by using high pressure homogenizer. Biotin was utilized as a drug and ceramide NP was utilized as a supporter of bilayer. The biotin was entrapped in aqueous core, while ceramide NP was packed in the bilayer of the ethosomes. Looking at the physical properties of vesicles containing ceramide NP, the sized was 80~130 nm, the polydispersity index was 0.09~0.16, and the zeta potential was -40~-49 mV. In vesicles without ceramide NP, the size was 124.80±1.46 nm, and the zeta potential and polydispersity index were -45.48±1.27 mV and 0.088±0.018, respectively. Therefore, the ethosome with ceramide NP has improved physical properties of vesicles compared to the ethosome without ceramide NP. Skin absorption rates of ethosomes with ceramide NP were 6.13~14.98%, while skin absorption rate of ethosome without ceramide NP was 7.08% at 12 h. In conclusion, ethosomes containing ceramide NP not only improved the skin absorption efficiency, but had also a positive effect on the stability of vesicles.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.7
• /
• pp.1031-1037
• /
• 2021

The frequency of marine accidents of vessels in Korea is steadily increasing and it is concentrated on small vessels with less than 10 tons of gross tonnage. Therefore, preventing capsizing accidents in small vessels is important to reduce the cost in terms of human and property damage due to such accidents. However, research on the seakeeping performance of small vessels has been insufficient, and there are no domestic and international regulations on seakeeping performance. Therefore, in this study, capsizing accidents caused by poor loading conditions were investigated by examining the adjudications of the small vessels in which the capsizing accidents occurred. Hydrostatic calculations and seakeeping performance analysis were performed for a representative vessel. A vessel generally performs a six-degree-of-freedom motion during operation. In this study, the response amplitude operator and response spectrum of a representative vessel were calculated to determine the roll motion. Moreover, a short-term statistical analysis of the vessel according to the loading conditions was performed for the wave stationary status for 3 h. From the results, it was estimated that, when the loading condition of a small vessel is poor, its roll motion increases, greatly reducing its stability.