• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.492-504
• /
• 2018

This study was conducted to investigate the effects of seaweed peeling (SP), glycolic acid peeling (GP) and general scrub (GS), which are widely known as cures for acne in both medicine and esthetics on the keratosis pilaris skin and provide basic data for a keratosis pilaris improvement program. For the experiment, subjects were categorized into control (GS) and experimental (GP and SP) groups, and tests were performed on arms and legs with relatively high keratosis pilaris symptoms (5 parts for each group) for 6 weeks. The keratin quantity, sebum content, moisture level and pigmentation were measured before and after (2, 4 and 6 weeks) the experiment and comparatively analyzed. The GP group showed an increase in moisture level (t=-4.064, p<0.01) but a decrease in pigmentation (t=3.536, p<0.01), while a decrease in keratin quantity (t=2.370, p<0.05) and pigmentation (t=4.017, p<0.01) was observed in the SP group and a decrease in keratin quantity (t=2.834, p<0.05) and an increase in moisture level (t=-7.589, p<0.001) was observed in the control group (GS). Additionally, the skin irritation reaction was lowest in the GS group. The SP group had the highest satisfaction with the improvement in response to keratosis pilaris care. When asked if they were willing to get the treatment with the same product, both SP and GP groups were high. In other words, keratosis pilaris care was needed in both experimental and control groups. Overall, the results of this study indicate that SP, GP and GS, which are commonly used in remedying acne, normalize turnover cycle by removing the dead cells from around the pores and improve keratosis pilaris symptoms by increasing moisture in the skin. Therefore, to improve keratosis pilaris skin, it is important to keep removing keratin and using a moisturizer that provides a skin barrier on a regular basis. The results presented herein will be useful as basic data for a keratosis pilaris improvement program.

• Journal of radiological science and technology
• /
• v.26 no.4
• /
• pp.21-26
• /
• 2003

To evaluate the newly designed gastroduodenal coil catheter:in-vitro test. The coil catheter that we made in our laboratory was 150 cm. The coil that is made of stainless steel wire was composed 1.3 mm inner diameter and this coil spring was covered with heat-shrinkable polyethylene tube. To measure the length under fluorocopy, 8 radiopaque marks were attached at 5 cm, 10 cm, 11 cm, 12 cm, 13 cm, 14 cm, 15 cm, 20 cm apart from distal end of the catheter and 6, 2, 1 pores were made at 7 cm, 13 cm, 19 cm apart from the distal end. Radio-opacity and the amount of injected contrast was investigated in formerly used 5 Fr. vessel catheter, which is possible in measuring length, and newly designed coil catheter. Film density was tested for radio-opacity with autodensitometer. For measuring the volume of injected salin, the catheter was located in the acryl box(26 cm, 3 cm, 16 cm) that divided into 4 chambers. After injection 50 cc of contrast with autoinjector, the contrast's quantity in each chamber was measured with and without over the guide wire. Radio-opacity was 0.51 in 5 Fr. vessel catheter, 0.31 in newly made catheter. The amount of injected contrast was measured. In case of 5 Fr. vessel catheter, the amount was 99.5% from the distal part, there was no difference between with and without the guide wire. Otherwise, using a coil catheter, the pacentage the ejected saline was 1.17%, 18.8%, 41.8%, 38.2% from the distal part with the guide wire, 19.5%, 32.6%, 27.7%, 20.3% without the guide wire. Compare with formerly established catheter, this new coil catheter is easy to measure the length thanks to easy confirming under fluoroscopy and excellent in injecting contrast. Therefore, newly designed gastrointestinal catheter seems to be useful in gastrointestinal intervention procedure.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.7
• /
• pp.16-19
• /
• 2019

A thinner film has superior electrical properties and a better amorphous structure. Amorphous structures can be effective in improving conductivity through a depletion effect. Research is needed on the Schottky contact, where potential barriers are formed, as a way to identify these characteristics. $SiO_2/SnO_2$ thin films were prepared to examine the amorphous structure and Schottky contact, $SiO_2$ thin films were prepared using Ar = 20 sccm. $SnO_2$ thin films were deposited using mixed gas with a flow rate of argon and oxygen at 20 sccm, and $SnO_2$ thin films were added by magnetron sputtering and treated at $100^{\circ}C$ and $150^{\circ}C$. To identify the conditions under which the amorphous structure was constructed, the XRD patterns were investigated and C-V and I-V measurements were taken to make Al electrodes and perform electrical analysis. The depletion layer was formed by the recombination of electrons and holes through the heat treatment process. $SiO_2/SnO_2$ thin films confirmed that the pores were well formed when heat treated at $100^{\circ}C$ and an electric current was applied over the micro area. An amorphous $SiO_2/SnO_2$ thin film with heat treatment at $100^{\circ}C$ showed no reflection at $33^{\circ}\;2{\theta}$ in the XRD pattern, and a reflection at $44^{\circ}2\;{\theta}$. The macroscopic view (-30 V

• Korean Journal of Organic Agriculture
• /
• v.26 no.3
• /
• pp.409-425
• /
• 2018

Occurrence and yield characteristics of lepidopteran insect pests in both PUR (paddy-upland rotation) and CU (continuing upland) fields for 8 maize (Eolrukchal 1, Heugjeom 2, Miheukchal, Ilmichal, Heukjinjuchal, Chalok 4, Mibaek 2, Daehakchal) and 7 sorghum (Hwanggeumchal, Anzunbaengisusu, Moktaksusu, Sodamchal, DS-202, Nampungchal, Donganme) varieties was surveyed. The population of Ostrinia furnacalis adults showed 3 times highest peaks in 2016. In addition, the damaged ratios of maize and sorghum leaves and stems were increased depending on the growth periods of the crops and those by O. furnacalis larvae were also increased steeply in mid August. The damaged ratios of maizes such as Miheukchal, Eolrukchal 1, Ilmichal, Heugjeom 2, and Mibaek 2 by O. furnacalis larvae were statistically different (P=0.05) between organically managed PUR and CU fields. Except for DS202 among sorghum varieties, the damaged ratios of the other ones were high and similar (50-92%) in the CU field. The ear damaged ratio of maize varieties by lepidopteran larvae including O. furnacalis and Helicoverpa armigera was from 5 to 38% in Chalok 4 and Heukjinjuchal, respectively, and Daehakchal gave relatively higher damage ratio in the PUR field (33%) than in the CU field (14%). The ear ratio of Sodamchal and DS-202 varieties in the PUR field was 94 and 82%, and all sorghum varieties were damaged over 78% by lepidopteran larvae in the CU field. Interestingly, the correlation coefficients between the damaged ratio and invasive pores on their stems by O. furnacalis larvae were positive (maize $r=0.69_{paddy-upland}$, $0.95_{continuing}$; sorghum $r=0.93_{paddy-upland}$, $0.97_{continuing}$, respectively). Additionally, the correlation coefficients between the damaged ratio and the ear weight or the thousand kernel weight (g) of maizes and sorghums by lepidopteran larvae were negative (maize $r=-0.38_{paddy-upland}$, $-0.49_{continuing}$; sorghum $r=-0.70_{paddy-upland}$, $-0.57_{continuing}$, respectively). These results indicate that the focused management on lepidopteran insect pests occurring maizes and sorghums cultivated in PUR and CU fields is an important strategy to secure their yields.

• Economic and Environmental Geology
• /
• v.53 no.6
• /
• pp.667-675
• /
• 2020

An Alum-sludge based adsorbent (ASBA) was synthesized by the hydrothermal treatment of alum sludge obtained from settling basin in water treatment plant. ASBA was applied to remove fluoride and arsenic in artificially-contaminated aqueous solutions and mine drainage. The mineralogical crystal structure, composition, and specific surface area of ASBA were identified. The result revealed that ASBA has irregular pores and a specific surface area of 87.25 ㎡ g-1 on its surface, which is advantageous for quick and facile adsorption. The main mineral components of the adsorbent were found to be quartz(SiO2), montmorillonite((Al,Mg)2Si4O10(OH)2·4H2O) and albite(NaAlSi3O8). The effects of pH, reaction time, initial concentration, and temperature on removal of fluoride and arsenic were examined. The results of the experiments showed that, the adsorbed amount of fluoride and arsenic gradually decreased with increasing pH. Based on the results of kinetic and isotherm experiments, the maximum adsorption capacity of fluoride and arsenic were 7.6 and 5.6 mg g-1, respectively. Developed models of fluoride and arsenic were suitable for the Langmuir and Freundlich models. Moreover, As for fluoride and arsenic, the increase rate of adsorption concentration decreased after 8 and 12 hr, respectively, after the start of the reaction. Also, the thermodynamic data showed that the amount of fluoride and arsenic adsorbed onto ASBA increased with increasing temperature from 25℃ to 35℃, indicating that the adsorption was endothermic and non-spontaneous reaction. As a result of regeneration experiments, ASBA can be regenerated by 1N of NaOH. In the actual mine drainage experiment, it was found that it has relatively high removal rates of 77% and 69%. The experimental results show ASBA is effective as an adsorbent for removal fluoride and arsenic from mine drainage, which has a small flow rate and acid/neutral pH environment.

• Korean Chemical Engineering Research
• /
• v.48 no.3
• /
• pp.391-396
• /
• 2010

In this research the characteristics of ammonia removal from malodorous waste-air were investigated under various operating condition of biofiilter packed with equal volume of rubber media and compost for the efficient removal of ammonia, representative source of malodor frequently generated at compost manufacturing factory and publicly owned facilities. Then the optimum conditions were constructed to treat waste-air containing ammonia with biofilter. Biofilter was run for 30 days(experimental frequency of 2 times/day makes 60 experimental times.) with the ammonia loading from $2.18g-N/m^3/h$ to $70g-N/m^3/h$ at $30^{\circ}C$. The ammonia removal efficiency reached almost 100% for I through IV stage of run to degrade up to the ammonia loading of $17g-N/m^3/h$. However the removal efficiency dropped to 80% when ammonia loading increased to $35g-N/m^3/h$, which makes the elimination capacity of ammonia $28g-N/m^3/h$ for V stage of run. However, the removal efficiency remained 80% and the maximum elimination capacity reached $55g-N/m^3/h$ when ammonia loading was doubled $70g-N/m^3/h$ for VI stage of run. Thus the maximum elimination capacity exceeded $1,200g-N/m^3/day$(i.e., $50g-N/m^3/h$) of the experiment of biofilter packed with rock wool inoculated with night soil sludge by Kim et al.. However, the critical loading did not exceed $810g-N/m^3/day$ (i.e., $33.75g-N/m^3/h$) of the biofilter experiment by Kim et al.. The reason to exceed the maximum elimination capacity of Kim et al. may be attributed to that the rubber media used as biofilter packing material provide the better environment for the fixation of nitrifying and denitrification bacteria to its surface coated with coconut based-activated carbon powder and well-developed inner-pores, respectively.

• Journal of the Mineralogical Society of Korea
• /
• v.29 no.2
• /
• pp.59-71
• /
• 2016

To investigate the sorption characteristics of Cs, which is one of the major isotopes of nuclear waste, on natural zeolite chabazite, XRD, EPMA, EC, pH, and ICP analysis were performed to obtain the informations on chemical composition, cation exchange capacity, sorption kinetics and isotherm of chabazite as well as competitive adsorption with other cations ($Li^+$, $Na^+$, $K^+$, $Rb^+$, $Sr^{2+}$). The chabazite used in this experiment has chemical composition of $Ca_{1.15}Na_{0.99}K_{1.20}Mg_{0.01}Ba_{0.16}Al_{4.79}Si_{7.21}O_{24}$ and its Si/Al ratio and cation exchange capacity (CEC) were 1.50 and 238.1 meq/100 g, respectively. Using the adsorption data at different times and concentrations, pseudo-second order and Freundlich isotherm equation were the most adequate ones for kinetic and isotherm models, indicating that there are multi sorption layers with more than two layers, and the sorption capacity was estimated by the derived constant from those equations. We also observed that equivalent molar fractions of Cs exchanged in chabazite were different depending on the ionic species from competitive ion exchange experiment. The selectivity sequence of Cs in chabazite with other cations in solution was in the order of $Na^+$, $Li^+$, $Sr^{2+}$, $K^+$ and $Rb^+$ which seems to be related to the hydrated diameters of those caions. When the exchange equilibrium relationship of Cs with other cations were plotted by Kielland plot, $Sr^{2+}$ showed the highest selectivity followed by $Na^+$, $Li^+$, $K^+$, $Rb^+$ and Cs showed positive values with all cations. Equilibrium constants from Kielland plot, which can explain thermodynamics and reaction kinetics for ionic exchange condition, suggest that chabazite has a higher preference for Cs in pores when it exists with $Sr^{2+}$ in solution, which is supposed to be due to the different hydration diameters of cations. Our rsults show that the high selectivity of Cs on chabazite can be used for the selective exchange of Cs in the water contaminated by radioactive nuclei.

• Journal of agriculture & life science
• /
• v.45 no.1
• /
• pp.59-66
• /
• 2011

This study was conducted to investigate the effect of vase material and floral preservative treatment over time on flower color, leaf color and flower size of cut flowers Rosa hybrida 'Aqua' and 'Corvernet', and Gerbera jamesonii 'Honeymoon' and 'Golden Time' stuck in a glass, porcelain, or onggi (pottery with a dark bronze glaze) vase containing either tap water or a floral preservative solution. The ${\Delta}E$ values in flower color of 'Aqua' rose at 8 days after treatment with a floral preservative in onggi and porcelain vases were low. The ${\Delta}E$ value of 'Covernet' rose treated with floral preservative in an onggi vase was the lowest and L value was the closest to that of petals of cut flowers at just before treatment (control). The ${\Delta}E$ value of 'Honeymoon' gerbera treated with a floral preservative in an onggi vase was the lowest and a value of 58.81 and b value of 34.29 were the closest to that of the control group as color of cut flowers in an onggi vase was similar to the color at the beginning of treatment. The ${\Delta}E$ value of 'Golden Time' gerbera treated in an onggi vase was significantly lower than that in a porcelain or glass vase and a value of -7.81 treated with a floral preservative solution in an onggi vase was the closest to the control and b value was high in an onggi vase as well. The L, a, and b values in leaf color of roses were similar to each value of the control and ${\Delta}E$ value of 3.25 measured in an onggi vase was lower than that in a porcelain or glass vase. Flower diameter of 'Covernet' and 'Golden Time' roses treated with a floral preservative in an onggi vase was greater than that in other treatments. From these results, the floral preservative applied to a holding solution is assumed to improve the quality and freshness of cut roses and gerberas by inhibiting microbes propagation and by promoting uptake of water and nutrients. The onggi vase with fine pores will promote the expression and maintenance of flower and leaf colors and may increase flower diameter by high air permeability.

• Journal of the Korean Ceramic Society
• /
• v.41 no.5
• /
• pp.395-400
• /
• 2004

The effects of compositions of binders on the rheological properties of mixtures and the preparation conditions on the formation of defects and the debinding characteristics of compacts for the injection molding of ceramic powders (65 wt% aluminaㆍ35 wt% feldspar) were studied. Ceramic powders were coated with 2 wt% of stearic acid and then mixed with 15, 20, and 25 wt% of Paraffin Wax (PW) and High Density Polyethylene (HDPE) as binders at $160^{\circ}C$ for 2 h. Rheological properties were investigated by using capillary rheometer. Apparent viscosities of mixtures were 80∼300 Paㆍs at 1,000$s^{-1}$ of a shear rate, it was good for the injection molding and depending on the compositions of binders. Short shot was formed at 15H5P5 (the ratio of HDPE : PW=5 : 5 in 15 wt% of binders) compacts without injection pressures and any noticeable defects were not formed at 45 kgf/$cm^{2}$ in 20H5P5 compacts. PW and HDPE were removed by the solvent extraction and thermal debinding method. Thermal debinding of HDPE at $450^{\circ}C$ for 5 h, which followed the extraction of PW was using n-heptane solvent at $70^{\circ}C$ for 5 h. Continuous pores in compacts, which facilitate the removal of HDPE by the thermal debinding, were found to form in the compacts when PW was removed by the solvent extraction. The optimum composition of binder at which binder was removed by thermal debinding without defects while maintaining the compact strength was 20H5P5. Bulk density, porosity and 3-point bending strength of 20H5P5 compact sintered at 1,30$0^{\circ}C$ for 5 h were 2.8, < 3%, and 2,400 kgf/$cm^{2}$, respectively, and can be used as a structural materials.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.5
• /
• pp.490-499
• /
• 2008

Statement of problem: Bioactive materials must have the ability to spontaneously form a bone like apatite layer on their surface and induce direct biochemical bonding to bone. A simple chemical treatment via alkali and heat has been revealed to induce bioactivity in titanium. Purpose: The purpose of this study was to evaluate the surface characteristics and stability of alkali and heat treated implants. Material and methods: Specimens were divided into three groups; group 1 was the control group with machined surface implants, groups 2 and 3 were treated with alkali solutions and heat treated in the atmosphere and vacuum conditions respectively. The surface characteristics were observed with FESEM, XPS, TF-XRD and AFM. Stability was evaluated with the resonance frequency analysis, periotest and removal torque values. One-way ANOVA and Duncan test were used for statistical analysis. Results: 1. Groups treated with alkali and heat showed similar characteristics. Groups 2 and 3 showed high compositions of Na ions on the surface with sub-micron sized pores compared to group 1. Group 2 showed mixed compositions of anatase and rutile with superior contents of rutile. 2. Resonance frequency analysis : The ISQ of group 2 showed significantly higher values than that of groups 1 and 3 at 12 weeks. The ISQ of groups 1 and 2 showed significant increase after 4 weeks, and the ISQ of group 3 increased significantly after 2 and 4 weeks respectively (P < .05). 3. Periotest: The PTV of groups 1 and 2 showed significant decrease after 4 weeks, and the PTV of group 3 showed significant decrease after 2 and 4 weeks respectively (P < .05). 4. Removal torque analysis: The removal torque value of group 2 was significantly higher than those of groups 1 and 3 at 2, 4 and 8 weeks. The removal torque values of groups 1 and 3 showed increase at 4 and 12 weeks, but the removal torque value of group 2 showed increase after 4 weeks (P < .05). Conclusion: An oxide layer with appropriate crystal structure and amorphous sodium titanate layer can be obtained on titanium implants through alkali and heat treatment in the atmosphere, and even alkali and heat treatment in vacuum conditions, provided a bioactive surface containing sodium. These surface layers can be considered to be effective for enhancement of osseointegration and reduction of healing period for implant treatment.