• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.774-780
• /
• 1999

The study of bond behavior between concrete and rebar has been performed for a long time. On this study, we tried to analysed variation of bond behaviors quantitatively with varying the strength of concrete. Bond stress which observed below the neutral surface of beam and at connecting part of beam and column is affected by various bond parameters. Resistance of deformed bars which embedded in concrete to the pullout force is divided 1) chemical adhesive force 2) frictional force 3) mechanical resistance of ribs to the concrete and these horizontal components of resistance is being bond strength. We selected the most common and typical variable which is concrete strength among various variables. So we used two kinds of concrete strength like as 25MPa(NSC) and 65MPa(HSC). Tension Test was performed to verify how bond behavior varied with two kinds of concrete strength. Concentration of bond stress was observed at load-end commonly in Tension Test of the initial load stage. At this stage stress distribution was almost coincident at each strength. As tension load added, this stress distribution had difference gradually and movement of pick point of bond stress to free-end and central section was observed. This tendency was observed at first and moving speed was more fast in NSC. At the preceeding result the reason of this phenomenon is considered to discretion of chemical adhesion and local failure of concrete around rebar in load-end direction. Especially, when concrete strength was increased 2.6 times in tension test, ultimate bond strength was increased 1.45 times. In most recent used building codes, bond strength is proportioned to sqare root of concrete compressive strength but comparison of normalized ultimate bond strength was considered that the higher concrete strength is, the lower safety factor of bond strength is in each strength if we use existing building codes. In Tension Test, in case of initial tensile force state, steel tensile stress of central cross section is not different greatly at each strength but tensile force increasing, that of central cross section in NSC was increased remarkably. Namely, tensile force which was shared in concrete in HSC was far greater than that of concrete in NSC at central section.

• Journal of Technologic Dentistry
• /
• v.36 no.2
• /
• pp.83-89
• /
• 2014

Purpose: This study is to evaluate the effect of modeling liquid on the shear-bond strength between zirconia core and veneering ceramic. Methods: Disk-shaped (diameter: 12.0mm; height: 3.0mm) zirconia were randomly divided into six groups according to the surface conditioning method and whether modeling liquid is used or not to be applied (N=60, n=10 per group): group 1-control group with distilled water(ZD); group 2-control group with modeling liquid(ZM); group 3-airborne particle abrasion with $110-{\mu}m$ $Al_2O_3$(AD) with distilled water; group 4-airborne particle abrasion with $110-{\mu}m$ $Al_2O_3$ with modeling liquid(AM); group 5-liner with distilled water(LD); group $6{\pounds}{\neq}liner$ with modeling liquid(LM). Contact angles were determined by the sessile drop method at room temperature using a contact angle measurement apparatus. The specimens were prepared using dentin veneering ceramics, veneered, 3mm high and 2.8mm in diameter, over the cores. The shear bond strength test was performed in a Shear bond test machine. Load was applied at a cross-head speed of 0.50mm/min until failure. The fractured zirconia surfaces were evaluated by using stereomicroscope (${\times}30$). Collected data were analyzed using SPSS(Statistical Package for Social Sciences) Win 12.0 statistics program. Results: ZD showed the highest contact angle($50.6{\pm}5.4^{\circ}$) and LD showed the lowest value($6.7{\pm}1.3^{\circ}$). Control groups and zirconia liner groups were significantly higher contact angle than liner groups(p<0.05). LD was the highest shear bond strength($43.9{\pm}3.8MPa$) and ZD was the lowest shear bond strength($24.8{\pm}4.9MPa$). Shear bond strengths of control groups and contact angle of liner groups were not significantly different((p>0.05). Liner groups presented adhesive failures. The others groups showed cohesive and adhesive failures. Conclusion: Modeling liquid groups showed lower contact angles and lower shear bond strength compared to those of distilled water groups.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.5
• /
• pp.5-13
• /
• 2008

In this study, It was carried out to evaluate the feasibility of recycled crushed concrete as aggregate used cement mortar replace sand and to investigate engineering properties of recycled aggregate for hazardous waste solidification. The compressive strength of cement mortar replaced 5-15% (wt.) recycled aggregate was over $163kgf/cm^2$ which is the standard of first grade concrete block class C. And cement mortar was examined to evaluate the stability by leaching test. Cu, Cd, Pb, Cr, and As as the heavy metals were proved very stable but mercury (Hg) was leached high concentration because it was simply tied to the cement surface. We investigated the crystal structures of cement mortar and they had shown the peaks of $Ca(OH)_2$, ettringite, and CSH (calcium silicate hydrate). As the result, the longer curing time, the higher CSH peak that means to increase compressive strength and the cement mortar was more stable. Therefore it was shown that it may be possible to apply hazardous waste solidification using recycled aggregate, fly ash and sewage sludge ash.

• Progress in Medical Physics
• /
• v.13 no.4
• /
• pp.202-208
• /
• 2002

The purpose of this study is to evaluate the monitor unit obtained from various methods for the treatment of superficial cancers using electron beams. Thirty-three breast cancer patients who were treated in our institution with 6, 9, and 12 MeV electron beams, were selected for this study. For each patient, irregularly shaped treatment blocks were drawn on simulation film and constructed. Using the irregular blocks, monitor units to deliver 100 cGy to the dose maximum (dmax) were calculated from measurement and three-dimensional radiation treatment planning (3D RTP) system (PINNACLE 6.0, ADAC Laboratories, Milpitas CA) Measurements were made in solid water phantom with plane parallel (PP) chamber (Roos, OTW Germany) at 100 cm source-to surface distances. CT data was used to investigate the effect of heterogeneity. Monitor units were calculated by overriding CT values with 1 g/㎤ and in the presence of heterogeneity. The monitor unit values obtained by the above methods were compared. The dose, obtained from measurement in solid water phantom was higher than that of RTP values for irregularly shaped blocks. The maximum differences between monitor unit calculated in flat water phantom at gantry zero position were 4% for 6 MeV and 2% for 9 and 12 MeV electrons. When CT data was used at a various gantry angle the agreement between the TPS data with and without density correction was within 3% for all energies. These results indicate that there are no significant difference in terms of monitor unit when density is corrected for the treatment of breast cancer patients with electrons.

• Geophysics and Geophysical Exploration
• /
• v.9 no.4
• /
• pp.304-315
• /
• 2006

We have examined the applicability of f-k analysis to the GPR direct wave measurement for water content to characterize vadose zone condition. When the vadose zone consists of a dry surface layer over wet substratum, we obtained f-k spectra where most of the energy is bounded by the air and dry soil velocities. In this case, dry soil velocity was successfully estimated by using high frequency data. On the other hands, when wet soil overlies dry substratum, the f-k spectra show a contrasting response where most of the energy travels with the velocity bounded by dry and wet soil velocities. In this case, the radar waves are trapped and guided within wet soil layer, exhibiting velocity dispersion. By adopting modal propagation theory, we could formulae a simple inversion code to find two layer's dielectric constants as well as layer thickness. By inverting the velocity dispersion curve obtained from f-k spectra of synthetic modeling data, we could obtain good estimates of dielectric constants of each layer as well as first layer thickness. Moreover, we could obtain more accurate results by including the higher mode data. We expect this method will be useful to get the quantitative property of real subsurface when the field condition is similar.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.4
• /
• pp.418-424
• /
• 2016

This study is an experimental study on the recycling of bottom ash in coal ash discharged from a thermal power plant. Bottom ash has limited research on recycling because it has more porous and higher water absorption ratio than fly ash. In this paper, the bottom ash was pulverized to a specific surface area of $4,000cm^2/g$ in order to use as a binder, and the flow, compressive strength test and microstructure analysis of the bottom ash based geopolymer mortar were performed. The flow measurement results of the geopolymer mortar showed that the flow rate was improved by increasing mixing water as the molar concentration of activator was increased. Compressive strength increased with increasing curing temperature and molar concentration. Through the microstructure analysis, we could confirm the geopolymer gel produced by the reaction of the condensation polymerization. It is considered that it is possible to make the bottom ash based geopolymer concrete through proper molar concentration of activator and high temperature curing.

• Korean Journal of Soil Science and Fertilizer
• /
• v.17 no.2
• /
• pp.161-166
• /
• 1984

The Cheju citrus orchards have been chemically fertilized with both phosphates high in Ca and Mg contents and potassium. The amount of chemical fertilizers consumed per unit area of cultivated land and the ratios of $P_2O_5$ and $K_2O$ to N in chemical fertilizers applied were much higher in the Cheju Island than those of the Korean mainland. These trends were particularly prominant in Southern Cheju where 70% of the Cheju citrus orchards are located. As the result of heavy applications of phosphate fertilizers, the available phosphorus of citrus orchard soils increased with increasing number of years under cultivation. The available phosphorus of sub-soil increased slightly with the number of years under cultivation compared to that of surface soil. Base saturation and pH increased with the number of years under cultivation, inasmuch as exchangeable bases such as Ca, Mg and K increased predominantly, but the cation exchange capacity did not vary in the citrus orchard soils.

• Proceedings of the KSAR Conference
• /
• 2003.06a
• /
• pp.46-46
• /
• 2003

Interleukin-10 (IL-10) is a homodimeric protein with a wide spectrum of anti-inflammatory and immune activities. It inhibits cytokine production and expression of immune surface molecules in various cell types. The transgenic mice carrying the human IL-10 gene in conjunction with the bovine $\beta$-casein promoter produced the human IL-10 in milk during lactation. Transgenic mice were generated using a standard method as described previously. To screen transgenic mice, PCR was carried out using chromosomal DNA extracted from tail or toe tissues with a primer set. In this study, stability of germ line transmission and expression of IL-10 gene integrated into host chromosome were monitored up to generation F15 of a transgenic line. When female mouse of generation F9 was crossbred with normal male, generation F9 to F15 mice showed similar transmission rates (66.0$\pm$20.13%, 61.5$\pm$16.66%, 41.1$\pm$8.40%, 40.7$\pm$20.34%, 61.3$\pm$10.75%, 49.2$\pm$18.82%, and 43.8$\pm$25.91%, respectively), implying that the IL-10 gene can be transmitted stably up to long term generation in the transgenic mice. For ELISA analysis, IL-10 expression levels were determined with an hIL-10 ELISA and a mIL-10 ELISA kit in accordance with the supplier's protocol. Expression levels of human IL-10 from milk of generation F9 to F13 mice were 3.6$\pm$1.20 mg/ml, 4.2$\pm$0.93 mg/ml, 5.7$\pm$1.46 mg/ml, 6.3$\pm$3.46 mg/ml, and 6.8$\pm$4.52 mg/ml, respectively. These expression levels are higher than in generation F1 (1.6 mg/ml) mice. We concluded that transgenic mice faithfully passed the transgene on their progeny and successively secreted target proteins into their milk through several generations, although there was a little fluctuation in the transmission frequency and expression level between the generations.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.1
• /
• pp.135-143
• /
• 2014

This study classified abnormal sea surface temperature changes of the central pacific region according to three evolution patterns. Focusing on typhoons that affect the Korean Peninsula, the research analyzed typhoon's occurrence spot and track, change in the central pressure characteristics, and the characteristics of change in typhoon precipitation and the number of occurrences of heavy rainfall in the Nakdong River Basin. As a result of analysis, in case of prolonged-decaying years and symmetric-decaying years, typhoon-related summer rainfall and heavy rainy days appeared to be higher than long-term average. But in case of abrupt-decaying years, the pattern of general decrease appeared. This is because typhoon's occurrence spot is located comparatively near the Korean peninsula, typhoon's central pressure is high, and typhoon's route generally moves to Japan. As the outcome, this study is expected to reduce flood damage through analyzing the characteristics of typhoon's activity according to CP El Ni$\tilde{n}$o evolution patterns and the characteristics of local typhoon rainfall. In addition, it is expected to provide useful information for establishing adaptation and mitigation to climate change.

• Applied Chemistry for Engineering
• /
• v.29 no.3
• /
• pp.298-302
• /
• 2018

Photocatalytic properties of nitrogen doped titanium dioxide were investigated. Photocatalytic degradation of methylene blue under UV and visible light was carried out to characterize N-doped $TiO_2$. The result of XPS indicated that nitrogen atoms substitute for oxygen sites within the crystal structure of $TiO_2$. In the UV-Vis DRS spectra, N-doped amorphous $TiO_2$ absorbed UV light with little absorption of visible light, while the absorption of visible light of amorphous/anatase $TiO_2$ remarkably increased. Methylene blue photocatalytic degradation appeared by the irradiation of UV or visible light onto the N-doped anatase phase of $TiO_2$. However, the degradation rate of visible light was lower than that of UV light. The photocatalytic degradation rate of the amorphous/anatase $TiO_2$ sample was higher than that of the anatase $TiO_2$. These results indicate that the high surface area of amorphous/anatase $TiO_2$ sample, which was about three times larger than those of the anatase $TiO_2$ sample, may be related to small particles of N-doped anatase $TiO_2$.