• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2011년도 춘계학술논문요약집
• /
• pp.383-384
• /
• 2011

• The Korean Journal of Ceramics
• /
• 제4권4호
• /
• pp.382-386
• /
• 1998

titanate and a silicon carbide/zirconium diboride particulate composite have each been blended with thermoplastic of aqueous binders and extruded. The green extrudates have diameters ranging between 50 and 150 ㎛ and polyethylene-base 150 ${\mu}m$ diameter fibers can be drawn down at elevated temperature to approximately 40 ${\mu}m$ diameter. Hollow fibers with 150${\mu}m$ outer and 90 ${\mu}m$ inner diameter can also be fabricated. Green fibers have been processed into chopped fiber felts for use as gas distributors/current collectors in an experimental solid oxide fuel cell (SOFC) and the first attempts at producing simple textile structures have been successful. The fibers, tubes and felts have been successfully debound and sintered and characterization of the sintered PSZ fibers, for example, has revealed a density in excess of 99% and tensile failure stresses up to 1.0 GPa for 78 ${\mu}m$ diameter fibers.

• 한국포장학회지
• /
• 제5권2호
• /
• pp.42-58
• /
• 1999

Packaging materials and articles that are used in food contact applications can transfer constituents in the foodstuffs. This kind of risk of possible health hazards to consumers has been generally recognized for a long time with the consequence of establishing corresponding food regulations in most developed countries. However, the language of these laws, their interpretation, and their level of enforcement vary from country to country. Accordingly, the actual migrating levels from packaging materials can be varied depending on the migration testing methods as prescribed in the national legislation in each countries. Therefore, there are needs of elimination of non-tariff trade barriers raised by sanitary and phytosanitary or technical measures under the Final Act of the UR Agreement. In this connection, the EU and USA are currently in an ongoing process of legislation harmonization to overcome potential barriers to free trade. In general, regulations governing component transfer in the USA are more complicated and comprehensive than similar regulations in Europe. In future, standard migration testing procedures for microwave heat susceptor materials and for the use of fatty food simulant should be established and also harmonized among countries. The objective of this investigation is to compare the current regulations for migration testing for plastic containers and packaging materials in USA, EU and Korea or Japan. For those regulations, Korean standards are required to be kept up with the international standards. By doing this, the related Korean regulation could be amended along with the worldwide progress for harmonization.

• 비파괴검사학회지
• /
• 제28권1호
• /
• pp.40-45
• /
• 2008

고체의 탄성 계수를 구하기 위한 방법으로 초음파의 종파와 횡파 속도를 측정하기 위하여 기존의 접촉식 초음파 시험법 대신 수침 초음파 시험법을 사용하였다. 통상적으로 수침법에서 종파 에코만 고려하는 것과 달리 모드 변환에 의한 횡파 에코를 찾아서 횡파 속도를 측정하였다. 물질의 두께를 알 수 없어 종파와 횡파 속도를 구할 수 없는 경우에도 두 속도의 비를 이용하여 포아송비를 구할 수 있었다. 다양한 재료를 대상으로 이 방법을 적용한 결과, 속도가 빠른 재료이거나, 포아송비가 작을수록 수침법에 의해 측정한 값이 정확하여 이러한 특징을 가진 세라믹이나 고강도 재료가 이 방법을 통한 종파와 횡파 속도 측정에 적당함을 알 수 있었다.

• 한국재난정보학회 논문집
• /
• 제4권1호
• /
• pp.102-136
• /
• 2008

Coated welding points are eliminated for Open-Inspection of above-ground storage tanks which should be inspected periodically in accordance with the Hazmat-treatment Safety Act. But it was speculated on this study that it causes such huge economical losses in terms of manpower and materials that applicable to magnetic particle testing. As a result, it was concluded that the magnetic particle testing is applicable to the coating depth below $50{\mu}m$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1608-1609
• /
• 2011

In this study, in order to develop the evaluation method for XLPE materials for HVDC cables, DC/Impulse superposition testing system was builded up. Throughout the P-spice simulation, optimal values of the protection resistor for the DC generation system and the blocking capacitor for the Impulse generator were calculated. DC/Impulse superposition system showed good result maintaining their proper wave shapes and amplitudes. This system would be planned to apply to the evaluation of XLPE materials for HVDC cables.

• 한국산업보건학회지
• /
• 제25권1호
• /
• pp.82-88
• /
• 2015

Objectives: This study is designed to analyze the penetration performance into ceiling materials containing asbestos of scattering prevention agents and investigate the change in penetration depth and viscosity according to the dilution rate of anti-scattering agents diluted with distilled water. Methods: Five different types of scattering prevention agents were spread on plate-type asbestos ceiling materials. The penetration depth of each coated ceiling material was measured by energy dispersive spectroscopy (EDS) analysis, based on X-ray fluorescence (XRF) results of the non-coated ceiling materials. Test equipment installed the ceiling materials and 60 minutes were collected at a flow rate of $10{\ell}/min$ at a filter of 25 mm. Results: An EDS analysis of the cross-section of ceiling materials constructed with a scattering prevention agent revealed that potassium is detected in the process of penetrating hardener solidification and this element could be an indicator for infiltration. When anti-scattering agents with different viscosities were constructed and the penetration depth was analyzed by potassium detection assessment using EDS, the depth results with viscosities of 5.0, 2.5, and 1.9 cP were 98.5, 103, and $147{\mu}m$, respectively. Penetration performance improved with decrease in viscosity. Conclusions: For asbestos ceiling materials, it is concluded that a higher dilution rate of the scattering prevention agent leads to lower viscosity, and hence a deeper penetration depth from $156{\mu}m$ to 3 mm. The asbestos anti-scattering properties according to the penetration depth will be confirmed through further study.

• 비파괴검사학회지
• /
• 제29권6호
• /
• pp.525-533
• /
• 2009

Emphasis in the paper is placed on describing guided wave successes and challenges for applications in aircraft and composite materials inspection. Guided wave imaging methods discussed includes line of sight, tomography, guided wave C-scan, phased array, and ultrasonic vibration methods. Applications outlined encircles lap splice, bonded repair patch, fuselage corrosion, water loaded structures, delamination, and ice detection and de-icing of various structures.

• Electronic Materials Letters
• /
• 제14권6호
• /
• pp.678-688
• /
• 2018

The repeated-bending properties of Sn-0.7Cu, Sn-0.3Ag-0.7Cu (SAC0307), and Sn-3.0Ag-0.5Cu (SAC305) solders mounted on flexible substrates were studied using highly accelerated stress testing (HAST), followed by repeated-bending testing. In the Sn-0.7Cu joints, the $Cu_6Sn_5$ intermetallic compound (IMC) coarsened as the HAST time increased. For the SAC0307 and SAC305 joints, the $Ag_3Sn$ and $Cu_6Sn_5$ IMCs coarsened mainly along the grain boundary as the HAST time increased. The Sn-0.7Cu solder had a high contact angle, compared to the SAC0307 and SAC305 solders; consequently, the SAC0307 and SAC305 solder joints displayed smoother fillet shapes than the Sn-0.7Cu solder joint. The repeated-bending for the Sn-0.7Cu solder produced the crack initiated from the interface between the Cu lead wire and the solder, and that for the SAC solders indicated the cracks initiated at the surface, but away from the interface between the Cu lead wire and the solder. Furthermore, the oxide layer was thickest for Sn-0.7Cu and thinnest for SAC305, regardless of the HAST time. For the SAC solders, the crack initiation rate increased as the oxide layer thickened and roughened. $Cu_6Sn_5$ precipitated and grew along the grain and subgrain boundaries as the HAST time increased, embrittling the grain boundary at the crack propagation site.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1996년도 The 9th KACG Technical Annual Meeting and the 3rd Korea-Japan EMGS (Electronic Materials Growth Symposium)
• /
• pp.527-527
• /
• 1996