• 한국지반공학회지:지반
• /
• 제7권3호
• /
• pp.51-64
• /
• 1991

말뚝기초 설계의 신뢰도및 경제성 향상을 위해서는 말뚝 지지력 예측의 신뢰도 제고가 필수적이다. 현재까지 수많은 말뚝지지력 예측 방법들이 제안되어 왔으나 말뚝재하시칩에 의하는 방법외에는 그 신뢰도가 보장되지 못하는 것이 현실이다. 그러나 말뚝재하시험은 상당한 시간과 비용이 소요되어 활성화 되지 못하였다. 말뚝의 주면마찰력을 선단부 재하의 반력으로 이용하는 SPLT의 개발은 이러한 문제점 들을 해소할 수 있는 방안으로 실무에 적용이 확산되고 있다. SPLT에서는 주면마찰력과 선단저항을 분리 측정하여 말뚝지지력 해석의 신뢰도를 높여줄 수 있는 이점이 있는 반 면, 주면마찰부에 작용하는 하중의 방향이 기존의 재하시험과 반대로 되는 문제점과 축소된 선단부 사용의 영향이 명확히 규명되지 못한 문제점이 해결되어야 할 과제로 제기되고 있다. 본 연구에서 는 이러한 영향을 알아보기 위하여 직경 406mm의 강관말뚝을 사용하여 SPLT의 1단계, 2단계 시험 후 재래식 재하시 칩을 수행하였다. 연구결과에 의하면 인발시의 주면마찰력은 압축시의 값보다 낮은 것으로 나타나 SPLT결과를 실 무에 적용하딴 안전율을 높여주는 효과를 주며, 축소된 선단부 사용은 치수효과 (scaleeffect)에 대한 적절한 해석후 적용할 수 있을 것으로 나타난다.

• 한국지반환경공학회 논문집
• /
• 제5권2호
• /
• pp.33-39
• /
• 2004

대부분의 말뚝기초는 두부 고정상태이지만, 수평재하시험은 일반적으로 두부 자유상태에서 시행되었다. 이번 논문은 두가지 경우(두부고정, 두부자유)에 대한 말뚝깊이별 수평변위와 이론 방정식과 현장수평재하시험을 비교해가며 대구경현장타설말뚝의 수평거동을 분석한 말뚝현장수평재하시험을 수행하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.1088-1093
• /
• 2010

The Smart bi-directional pile load test with variable end plate overcomes the shortcoming of the Osterberg cell test. It is possible that the ultimate bearing capacity of piles can be known by using two different end plates. The first step is to measure end bearing capacity with smaller end plate and the second step is similar to the conventional O-cell test. In this study, model test was performed to evaluate the smart bi-directional pile load test in sand. Vertical displacement of the model pile were messured at the axial loading condition.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1132-1143
• /
• 2008

A single Column/Shaft which extended the pile to the column of the bridge with same diameter has better safety and economical profit, but it usually has larger lateral displacement due to lateral loads such as wind, earthquake, wave, etc. A series of horizontal pile load testing were performed to study the lateral behavior of single column/shaft with varying different free lengths and embedded pile lengths. Eight instrumented test piles were cast-in-placed by bonding strain gauges at certain locations on both faces of the pile to measure bending moment, from two-way loadings. Linear variable differential transformers(LVDTs) were installed to measure the lateral pile displacement. Based on this, it is found that the test single column/shaft with different free lengths shows different failure modes. If the test pile has a longer free length, the failure occurs at the near the ground surface, but the shorter one's failure occurs at the below the ground surface.

• Geomechanics and Engineering
• /
• 제29권4호
• /
• pp.407-420
• /
• 2022

Embedded piles, which are typically used in Korea, are precast piles inserted into prebored ground with cement paste. Dynamic pile tests tend to underestimate the bearing capacity of embedded piles because of the undeveloped shaft resistance prior to the curing of the cement paste and the insufficient energy transferred after the curing. In this study, a resistance combination method using the base resistance before the cement paste is cured and the shaft resistance after the cement paste is cured is proposed to obtain a combined load-settlement curve from dynamic pile tests. Two pairs of embedded piles with diameters of 600 and 500 mm are installed. Each pair comprises one pile for the dynamic pile test and another pile for the static load test. The shape of the load-settlement curve obtained using the proposed method is similar to that obtained from the static load test. Thus, the resistances evaluated using the proposed method at selected settlements are similar to those obtained from the static load test. This study shows that the resistance combination method may be used effectively in dynamic pile tests to accurately evaluate the bearing capacity of embedded piles.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1998년도 봄 학술발표회 논문집
• /
• pp.203-212
• /
• 1998

• 대한토목학회논문집
• /
• 제28권6C호
• /
• pp.379-388
• /
• 2008

대형말뚝기초의 양방향 재하시험에서 재하용량 기준이 정확하게 규정되어 있지 않다. 그래서 양방향말뚝재하시험을 수행함에 있어 많은 혼란이 발생하고 있으며 재하용량에서 최대 2배까지의 차이가 나타나고 있다. 본 연구에서는 양방향 말뚝재하시험 기준들을 고찰하였으며, 국내에서 수행된 양방향 말뚝재하시험 사례들에 기초하여 최대등가시험하중, 재하하중 증가비, 재하용량 증가비 및 설계하중 충족비를 분석하였다. 양방향 말뚝재하시험 기준은 1방향 재하용량으로 정의되어야 하며, 1방향 재하용량은 설계하중의 2배 이상 이어야 한다는 것을 알 수 있었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.476-481
• /
• 2009

Bi-directional load test is one of O-cell tests. The O-cell test is a system which may be used for performing static load tests on cast in situ reinforced concrete bored piles. The technique was devised and developed by Osterberg of Northwestern University(USA) and has been in use around the world. The principle of the method is that an O-cell is installed in a cast in situ bored pile base. Once the pile concrete reaches its design strength the cell is connected to an hydraulic pump and pressured. Pressurization causes the cell to expand, developing an upward force on the section of pile above the cell loads, pile movements and strains within the pile then enable the capacity of the pile and its load settlement curves to be ascertained. The O-cell pile load test with variable end plate is operated on second steps - the first step is to confirming end bearing capacity with variable end plate and the second step is similar to the conventional O-cell test. In the study, To calculate ultimate capacity of bi-directional load test using model with the pile with variable end plate O-cell.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1195-1205
• /
• 2008

Composite piles have been used in ground conditions where conventional piles are unsuitable or uneconomical. They may consist of a combination of timber and concrete pile in Europe. One method of doing this was to drive a steel tube to just below water level, and a concrete pile was lowered down it and driven to the required level where corrosion was susceptible in U.K. Recently, a fiber reinforced polymer (FRP) composite pile was developed to use in many marine locations for piers and waterfront buildings in the USA(Hoy, 1995; Phair, 1997). A steel composite (SC) pile reinforced concrete spun pile with steel tube was also proposed and used for the foundation acting a high lateral earthquake load. Composite piles have been developed and researched to increase lateral resistance or to prevent corrosion in marine structures. In paper, the composite pile consisting of the steel upper portion and the concrete lower portion is proposed and are carried out several tests to confirm the capacity of the pile such as lateral load test, dynamic load tests and bending test. It is noted that the composite pile would be a economical pile being capable of increasing lateral resistance.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.447-454
• /
• 2003

In this test, two separated oil jacks were placed at bottom of drilled shaft(D = 1,500mm, L = 33m), and maximum upward and downward load of 1,250 tonf was applied. Also, the deformable rod sensors were placed on each level, and axial strains at each level were measured. Because the side skin friction and the end bearing could be measured separately in the Osterberg type pile load test, this test might be more economical and more applicable than a conventional static pile load test. Thus, if this Osterberg type pile load test could be established during design stage, construction cost might be reduced and its application for large diameter pile could be enhance greatly.