• 한국전자파학회논문지
• /
• 제17권3호
• /
• pp.272-279
• /
• 2006

본 논문에서는 W-CDMA(Wide band Code Division Multiple Access) 시스템에서 채널 측정 및 프레임 동기 확인에 사용되는 파일럿 비트 패턴의 프레임 동기 단어(frame synchronization words) 성능을 분석한다. 또한 W-CDMA 시스템에서는 두 개의 수신 단말기를 갖지 않고도, 다른 주파수의 측정을 하기 위해 압축 모드(compressed mode)를 사용한다. 제안된 프레임 동기용 이원 부호의 우선 쌍 간의 보완 매핑(complementary mapping) 관계를 이용하면, 압축 모드에서도 프레임 동기 특성을 유지함을 컴퓨터 시뮬레이션을 통하여 확인한다. 검출 확률과 오 경보 확률을 갖는 수신기 동작 특성(ROC: Reciever Operating Characteristic) 곡선은 LLRT(Log Likely-hood Ratio Test), GLRT(Generalied Likeiyhood Ratio Test), 연판정(soft correlation test), 경 판정(hard correlarion test)과 같은 다양한 검출법(detection metrics)을 이용하여 레일레이 페이딩 채널에서 제안된 프레임 동기 단어의 성능 분석에 사용된다. 이 논문의 파일럿 비트 패턴의 성능에 대한 연구 결과는 3세대 W-CDMA 시스템에서 프레임 동기의 설계 및 구현에 유용한 참고 자료가 될 수 있을 것이다.

• 한국정보처리학회논문지
• /
• 제7권10호
• /
• pp.3226-3235
• /
• 2000

반도체 집적 회로가 점점 복잡해지고 고속화되면서 반도체 집적 회로의 동작에 대한 검사 뿐 아니라, 회로가 원하는 시간 내에 동작함을 보장하는 지연 고장 검사의 중요성이 점점 커지고 있다. 본 논문에서는 경로 지연 고장에 대한 효율적인 테스트 입력 생성을 위하여 새로운 부분 확장 주사 방법을 제안한다. 본 논문에서는 유추와 할당을 적용한 테스트 입력 자동 생성기를 기반으로 하여 새로운 부분 주사 방법을 구현하였다. 우선적으로 표준 주사환경에서 테스트 입력을 생성한 후에 테스트 입력이 제대로 생성되지 않은 주사 사슬에 대하여 테스트 입력 생성기를 수행하는 동안의 정보를 이용하여 확장 주사 플립플롭이 적용될 플립플롭을 결정하였다. 확장 주사 플립플롭을 결정하는 기준으로서는 고장 검출율과 하드웨어 오버헤드를 사용하였다. 순차 회로인 ISCAS 89 벤치 마크 회로를 이용하여 실험을 수행하였으며, 실험을 통하여 표준 주사와 확장 주사 환경, 부분 확장 주사 환경에서 고장 검출율을 비교, 확인하였다. 그리고 새로운 알고리즘이 적용된 부분 확장 주사 방법에서 높은 고장 검출율을 확인함으로써 효율성을 입증하였다.

• 대한조선학회논문집
• /
• 제48권1호
• /
• pp.15-22
• /
• 2011

In this paper, cavitation patterns of model tests were compared with those of full-scale measurement for a propeller of crude oil carrier which was suffered from erosions on suction side of blade tip region. Cavitation tests were performed at design and ballast draft using model and full scale nominal wakes. A model ship and wire mesh method was used for the simulation of wake patterns of model nominal wakes. For the prediction of full-scale wake patterns, a RANS solver(Fluent 6.3) was used and wire mesh method was used for the simulation of the full scale wakes. Comparison results show that cavitation patterns using predicted full-scale wake patterns are closer to cavitation patterns of full-scale measurement at ballast draft condition. Also, cloud cavitations were observed on the position of eroded area at both full-scale measurement and cavitation tests using simulated full-scale wake patterns.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.1065-1068
• /
• 1998

This paper proposes a new test generation method. Most of the test generation methods are gate-level based, but our scheme is VHDL based, especially in other word, behavioral-level based. Our test pattern generation method uses software test method. And we generate deterministic test pattern with this method. The purpose of our method is to reduce the time and effort to generate the test patterns for the end-product test of IC.

• 한국주거학회논문집
• /
• 제10권4호
• /
• pp.137-146
• /
• 1999

The purpose of this study is to analyze the behavioral patterns and furniture usage in An-Bang of apartment. For this purpose, a survey was conducted by 215 housewives who lives in Taegu by the size of floor space, 20-49 Pyong. The data were analyzed by using frequencies, percentage, mean, factor analyzing, χ²-test, cluster analyzing. The results of the study are as follows: 1. The major behavioral patterns in an-bang is sleeping, make-up. fitting, but can't be neglected family-gathered and guest meeting. 2. The patterns of furniture usage are grouped into four clusters and principle furniture arrangement is floor type. 3. Behavioral patterns and furniture usage related with factors.

• 한국주거학회논문집
• /
• 제11권3호
• /
• pp.65-73
• /
• 2000

The purpose of this study is to analyze the Apprehension inclination and Behavioral Patterns in Single Detached Urban Dwellings. For this purpose, a survey was conducted by 200 housewives who live in Daegu. The data were analyzed by using frequencies, percentage, mean, factor analysis, $x^2$ -test. The results of this study are as follows: 1. An-Bang of the Single Detached Urban Dwellings has been still shown traditional Apprehension inclination. 2. 5 types of Behavioral patterns in An-Bang are identified. 5 types of Behavioral patterns are related with Seating style. 3. Apprehension inclination in An-Bang are identified. 5 types of Behavioral Patterns and Seating style.

• Journal of Information Display
• /
• 제10권1호
• /
• pp.6-15
• /
• 2009

In this paper, a new approach is proposed for the efficient generation of computer-generated holograms (CGHs) using the spatially redundant data on a 3D object and the novel look-up table (N-LUT) method. First, the pre-calculated N-point principle fringe patterns (PFPs) were calculated using the 1-point PFP of the N-LUT. Second, spatially redundant data on a 3D object were extracted and re-grouped into the N-point redundancy map using the run-length encoding (RLE) method. Then CGH patterns were generated using the spatial redundancy map and the N-LUT method. Finally, the generated hologram patterns were reconstructed. In this approach, the object points that were involved in the calculation of the CGH patterns were dramatically reduced, due to which the computational speed was increased. Some experiments with a test 3D object were carried out and the results were compared with those of conventional methods.

• KSTLE International Journal
• /
• 제9권1_2호
• /
• pp.10-12
• /
• 2008

Silicon micro-patterns were fabricated on Si (100) wafers using photolithography and DRIE (Deep Reactive Ion Etching) fabrication techniques. The patterned shapes included micro-pillars and micro-channels. After the fabrication of the patterns, the patterned surfaces were chemically modified by coating Z-DOL (perfluoropolyether, PFPE) thin films. The surfaces were then evaluated for their micro-friction behavior in comparison with those of bare Si (100) flat, Z-DOL coated Si (100) flat and uncoated Si patterns. Experimental results showed that the chemically treated (Z-DOL coated) patterned surfaces exhibited the lowest values of coefficient of friction when compared to the rest of the test materials. The results indicate that a combination of both the topographical and chemical modification is very effective in reducing the friction property. Combined surface treatments such as these could be useful for tribological applications in miniaturized devices such as Micro/Nano-Electro-Mechanical-Systems (MEMS/NEMS).

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.723-726
• /
• 1998

Fault dropping is a very important part of test generation process. It is used to reduce test generation time. Test generation systems use fault simulation for the purpose of fault dropping by identifying detectable faults with generated test patterns. Two kinds of delay fault model is used in practice, path delay fault model and gate delay fault model. In this paper we propose an efficient method for gate delay test generation which shares second test vector.

• 대한의용생체공학회:의공학회지
• /
• 제29권4호
• /
• pp.323-328
• /
• 2008

A patient with respiratory disorders such as a sleep apnea is increasing as the obese patient increase on the modern society. Positive Airway Pressure (PAP) devices are used in curing patient with respiratory disorders and turn out to be efficacious for patients of 75%. However, these devices are required for evaluating their performance to improve their performance by the mechanical breathing simulator. Recently, the mechanical breathing simulator was studied by the real time feedback control. However, the mechanical breathing simulator by an open loop control was specially required in order to analyze the effect of flow rate and pressure after operating the breathing auxiliary devices. Therefore the aims of this study were to make the mechanical breathing simulator by a piston motion and a valve function from the characteristic test of valve and motor, and to duplicate the flow rate and pressure profiles of some breathing patterns: normal and three disorder patterns. The mechanical simulator is composed cylinder, valve, ball screw and the motor. Also, the characteristic test of the motor and the valve were accomplished in order to define the relationship between the characteristics of simulator and the breathing profiles. Then, the flow rate and pressure profile of human breathing patterns were duplicated by the control of motor and valve. The result showed that the simulator reasonably duplicated the characteristics of human patterns: normal, obstructive sleep apnea (OSA), mild hypopnea with snore and mouth expiration patterns. However, we need to improve this simulator in detail and to validate this method for other patterns.