• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.1156-1167
• /
• 2010

The constant rate of strain (CRS) consolidation test has been widely used to evaluate consolidation characteristics of soils instead of the standard Incremental Loading Test. In practical problems, after the ground improvement, the condition of the soil is over-consolidated. Therefore, it is important to determine the recompression indices and the coefficient of consolidation(or the coefficient of swelling) of unloading-reloading cycle to predict the settlement behavior. However, since standard testing procedures or studies related with strain rate are insufficient especially in unloading-reloading cycle, it is difficult to predict the settlement field behavior accurately from the CRS consolidation test results in spite of its lots of strengths. The several CRS consolidation tests were performed changing the unloading strain rate from 0.2%/hr to 20%/hr with vertical drainage condition using the reconstituted kaolinite sample. For the reconstituted kaolinite sample in CRS consolidation test, the recompression indices are insensitive to the strain rate. It is revealed that the coefficient of consolidation of reloading is affected by the developed pore pressure during unloading. Additionally, the test should be conducted in the positive pore pressure ratio range (3~15%) to obtain the reasonable coefficient of consolidation in the whole range(loading, unloading and reloading).

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1024-1029
• /
• 2008

In this study, new parameter related with compression index was derivated from piezocone test results. It is assumed that the consolidation coefficient obtained by piezocone test is concerned with the volume change during piezocone dissipation. Based on that assumption, new parameter in terms of consolidation coefficient from piezocone test was introduced. The new parameter from piezocone test and the compression index from laboratory consolidation test shows linear relationship.

• 토지주택연구
• /
• 제9권3호
• /
• pp.1-8
• /
• 2018

유럽과 미국에서는 말뚝기초 설계에 한계상태설계법 사용이 거의 정착되었으며, 세계적 추세에 따라 국내에서도 국토해양부가 한계상태설계법에 기반한 교량하부기초 설계기준을 제정하였지만, 국내 말뚝공법 및 지반조건에 대한 저항계수 연구가 부족하여 당장 설계에 반영하기에는 어려운 여건이었다. 이에 본 연구에서는 국내에서 많이 사용되고 있는 PHC 매입말뚝의 저항계수를 구하기 위하여 LH설계기준과 도로교설계기준 방법으로 산정한 지지력과 LH 현장에서 실시한 정재하시험(21회)과 동재하시험(EOID 21회, Restrike 21회) 결과를 신뢰성분석을 실시하였으며, 선행 논문(재하시험에 의한 PHC 매입말뚝의 저항계수 산정)에서 수행한 결과보다 2배 이상 많은 데이터를 추가하여 분석하였다. 그 결과 정재하지지력(극한)으로 구한 저항계수는 설계식 및 목표신뢰도지수에 따라 0.64~0.83, 동재하지지력(극한)으로 구한 저항계수는 0.42~0.55로 나와 정재하지지력(극한)으로 구한 저항계수보다 약 33% 작게 나타났다. 반면 수정동재하지지력(EOID의 극한선단지지력 + Restrike의 극한주면지지력)으로 구한 저항계수는 0.55~0.71로 나와 정재하지지력(극한)으로 구한 저항계수와 비교 시 그 차이가 약 14%로 줄어들었다. 데이터 추가에 의해 저항계수를 산정한 결과 이전 저항계수와 같거나 0.04정도 증가하여 데이터가 2배 이상 추가되어도 저항계수가 의미 있을 정도로 크게 변하지 않은 것으로 나타났다. 결론적으로 본 연구에서 정재하 및 동재하시험으로 산정한 전체 저항계수는 전반적으로 도로교설계기준(2015)에서 제시한 저항계수 0.3보다 커서 경제적인 설계가 가능한 것으로 나타났다.

• 동의생리병리학회지
• /
• 제25권6호
• /
• pp.1050-1055
• /
• 2011

This paper presents a novel diagnostic method to determine Sasang Consitution (SC) by elasticity coefficient of hand dorsal skin of elderly people. For this purpose, we carried out a clinical test, in which Our SC diagnostic tool and one Oriental medical doctor with SC medicine expertise participated to categorize 458 healthy subjects into four constitutions. After excluding heavy-noise, we extracted 295 subjects' elasticity coefficient feature data and statistically analyzed their SC relevance with ANOVA test. It resulted in that, Taeum-in has high elasticity coefficient compared to Soeum-in in a significance level of 0.05. There are no differences of elasticity coefficient in genders. This result is supported by the theory of Longevity and Life Preservation in Eastern Medicine(Donguisusebowon, 동의수세보원) which suggested that Taeum-in's flesh is solid and Soeum-in's one is tender. This is the first work which reports the relatedness of skin elasticity coefficient and SC by an objective clinical test.

• 대한조선학회논문집
• /
• 제48권4호
• /
• pp.363-367
• /
• 2011

In this paper, friction coefficients between ices and model ship were studied in order to predict the resistance of ice. The friction coefficient is a dimensionless scalar value which describes the ratio of the force of friction between two bodies and the force pressing them together. The coefficient of friction depends on the materials, roughness on surface, lubrication, etc. We tested and analyzed the friction coefficient for the development of the test methodology. The friction coefficient for ice model test is very dominant to predict the ship performance, so every ice tank uses their own painting technique. In this study, the friction coefficient with changing the moving speed of ice was studies by using a flat plates which were made by the MOERI's paining technique and the basic research for the developing the paining methodology in the MOERI ice model basin was carried out.

• 한국지반환경공학회 논문집
• /
• 제14권3호
• /
• pp.13-17
• /
• 2013

Determination of geotechnical characteristics of soil is either to use the field samples to measure the characteristics of soil through laboratory test or measuring the characteristics directly in the field. Field test can be derived similar value by considering characteristics of site and laboratory test can be confirmed the characteristic of soil by testing with field samples. This article describes relative density as the measure of compaction for cohesionless soils and presents several simple and mathematical relationships to help engineers estimate needed parameters for relative density calculations. The main purpose of this research is to investigate possible correlations between coefficient of uniformity, coefficient of curvature, maximum and minimum void ratio, mean grain size. Results show a linear relationship between the minimum and maximum void ratios and a power function relationship between coefficient of uniformity and the limiting void ratios. Void ratio range, which is the difference between the maximum and minimum void ratios, appeared to be log normally distributed but showed no simple mathematical fit to the data. these results were shown to help engineers estimate needed parameters for relative density calculations.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.140-145
• /
• 2002

At present, wind tunnel test or CFD is used for predicting aerodynamic drag coefficient in motor company. But, wind tunnel test requires much cost and time, and CFD has about 30% error. In this study a predicting program of the aerodynamic drag coefficient based on empirical techniques was developed. Also a mathematical optimization method using GRG method was added to the program. The program was applied to six cars. Aerodynamic drag coefficient values of six cars were Predicted with 4.857% average error. The optimization method was also applied to six cars. Three parameters selected from sensitivity analysis were determined to reduce the afterbody drag coefficient to the value established by a designer and when some parameters were changed for a developing automotive, optimal modifiable parameters were determined to preserve the same drag coefficient as the original automotive. It was verified that this program could predict the aerodynamic drag coefficient effectively and accurately, and this program with GRG method could determine optimal values of parameters.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.483-488
• /
• 2004

The inter-laboratory comparison test which is demanded on the authorized test of ISO/IEC 17025 is the program to guarantee the confidence of test result. This paper, as a part of the inter-laboratory comparison test between South Korea and China, is refered to the characteristic of friction coefficient of disk brake lining for rolling stock according to disk type. Brake tests were carried out under constant brake force and operating sequence by using dynamo-tester according to disk and disk lining types. To establishing the confidence of test result, we calculated A type uncertainty about friction coefficient and investigated the factors about the variation of friction coefficient.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2003년도 추계학술발표회 논문집
• /
• pp.169-174
• /
• 2003

Design of a rational earth volume conversion coefficient is required as the earth volume conversion coefficient may give great influence on construction work volume and construction costs in the civil engineering works where large-scaled earth volume is excavated. However, there are a great deal of difficulties in the calculation of the exact spoil surface earth and Insufficient earth volume by adopting the figures presented on the generally used design specifications which are not the results obtained from the selection tests in calculating the earth volume conversion coefficient. In this connection, it would be desirable to calculate the earth volume conversion coefficient by carrying out large-scaled site test adequate for the relevant environment. In consequence, this study aims at calculating the exact earth volume conversion coefficient of cutting and banking areas of weathering rocks in large-scaled construction sites where land is being developed into home lots. For this, we have excavated the respective 20 sites of the cutting and banking areas in the said site and then calculated the volume after the excavation. As a result, the relative exactness degree of the crossing was calculated at 0.5% in average. The relative exactness degree of 0.5% in the volume may be judged as an exact measurement as it corresponds to 0.17% of the relative exactness degree in the length measurement. We have calculated the exact earth volume conversion coefficient by the use of function ratio as per the wet unit weight and the indoor soil quality test as per volume calculated. And then we have found out minor differences as a result of the comparison and analysis with the earth volume conversion coefficient determined by the dry unit weight test as per sand replacement method. This may be judged as a rational design method for the calculation of earth volume conversion coefficient, as well as high reliability of site test as a precision photogrammetry is adopted for volume measurement of the irregular excavating areas.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.96-100
• /
• 2002

The purpose of this paper is presented a rational method of predicting dynamic/impact tensile strength of high tensile steel materials widely used fur structural material of automobiles. It is known that the ultimate strength is related with the loading speed and the Lethargy Coefficient from the tensile test. The Dynamic Lethargy Coefficient is proportional to the disorientation of the molecular structure and indicates the magnitude of defects resulting from the probability of breaking the bonds responsible for its strength. The coefficient is obtained from the simple tensile test such as failure time and stresses at fracture. These factors not only affect the static strength but also have a great influence on the dynamic/impact characteristics of the joist and the adjacent structures. This strength is used to analyze the failure life prediction of mechanical system by virtue of its material fracture. The impact tensile test is performed to evaluate the life parameters due to loading speed with the proposed method. Also the evaluation of the dynamic/impact effect on the material tensile strength characteristics is compared with the result of Campbell-Cooper equation to verify the proposed method.