• Structural Engineering and Mechanics
• /
• 제88권2호
• /
• pp.189-200
• /
• 2023

Silicate glass is usually a brittle and plate-like material, and it is difficult to measure the elastic modulus by the traditional method. This paper develops a test method for the glass elastic modulus based on the fundamental frequency of the cantilever beam with an elastic support and a free end. The method installs the beam-type specimen on a semi-rigid support to form an elastic support-free end beam. The analytic solution of the stiffness coefficients of the elastic support is developed by the fundamental frequency of the two specimens with known elastic modulus. Then, the glass elastic modulus is measured by the fundamental frequency of the specimens. The method significantly improves the measurement accuracy and is suitable for the elastic modulus with the beam-type specimen whether the glass is homogeneous or not. Several tests on the elastic modulus measurement are conducted to demonstrate the reliability and validity of the test method.

• Architectural research
• /
• 제10권2호
• /
• pp.37-42
• /
• 2008

This study is to get the proper evaluation of the residual property of reinforced concrete beam exposed to fire. This study focused on the strength resistance and analytical evaluation of RC members exposed high temperature. And this study is the basis analytical research to conduct the other studies. To analysis by the finite element method, the Total-RC program was used to analysis it and the Total-Temp program was also used to analysis the temperature distributions at the section. All of results were compared with the pre-existing experimental data of simple supported beam. Using it, the parameters influencing the structural capacity of the high temperature-damaged RC members and residual strength estimation are investigated. The temperature distribution and the structural capacity at the section are calculated in this step. An application of this method is compared with the heating test result and residual property test for simple supported beam which is subjected to ISO 834 test fire. The results of this study are as follows; 1) The loads-displacement relationship of RC beam, considering initial thermal stress of cross section and heat transfer analysis are estimated comparing analytical value with pre-existing experimental results. 2) by the heating time (0, 1, 2 hours), the results of analysis with parameters show that the load capacity exposing at fire is affected.

• Steel and Composite Structures
• /
• 제28권4호
• /
• pp.471-482
• /
• 2018

The composite reinforced concrete and steel (RCS) structural systems have larger structural lateral stiffness, higher inherent structural damping, and faster construction speed than either traditional reinforcement concrete or steel structures. In this paper, four RCS subassemblies with or without the RC slab designed following a strong column-weak beam philosophy were constructed and tested under reversed-cyclic loading. Parameters including the width of slab and composite effect of the RC slab and beam were explored. The test results showed that all specimens performed in a ductile manner with plastic hinges formed in the beam ends near the column faces. The seismic responses of composite connections are influenced significantly by different width of slabs. Compared with that of the steel beam without the RC slab, it was found that the load carrying capacity of composite connections with the RC slab increased by 30% on average, and strength degradation, energy dissipation also had better performance, while the ductility of that were almost the same. Furthermore, the contribution of connection deformation to the overall specimen displacement was analyzed and compared. It decreased approximately 10% due to the coupling effect in the columns and beams with the RC slab. Based on the test result, some suggestions are presented for the design of composite RCS joints.

• Structural Engineering and Mechanics
• /
• 제72권3호
• /
• pp.367-382
• /
• 2019

This paper presents experimental and analytical investigations on additional fixed-end rotations resulting from the strain penetration of high-strength reinforcement in reinforced concrete (RC) beam-column connections under monotonic loading. The experimental part included the test of 18 interior beam-column connections with straight long steel bars and 24 exterior beam-column connections with hooked and headed steel bars. Rebar strains along the anchorage length were recorded at the yielding and ultimate states. Furthermore, a numerical program was developed to study the effect of strain penetration in beam-column connections. The numerical results showed good agreement with the test results. Finally, 87 simulated specimens were designed with various parameters based on the test specimens. The effect of concrete compressive strength ($f_c$), yield strength ($f_y$), diameter ($d_b$), and anchorage length ($l_{ah}$) of the reinforcement in the beam-column connection was examined through a parametric study. The results indicated that additional fixed-end rotations increased with a decrease in $f_c$ and an increase in $f_y$, $d_b$ and $l_{ah}$. Moreover, the growth rate of additional fixed-end rotations at the yielding state was faster than that at the ultimate state when high-strength steel bars were used.

• Structural Engineering and Mechanics
• /
• 제52권3호
• /
• pp.559-572
• /
• 2014

This paper presents the results of an experimental investigation on the flexural behavior of doubly reinforced lightweight concrete (R.L.C.) beams tested under cyclic loading. A total of 20 beam specimens were tested. Test results are presented in terms of ductility index, the degradation of strength and stiffness, and energy dissipation. The flexural properties of R.L.C. beam were compared to those of normal concrete (R.C.) beams. Test results show that R.L.C. beam with low and medium concrete strength (20, 40MPa) performed displacement ductility similar to the R.C. beam. The ductility can be improved by enhancing the concrete strength or decreasing the tension reinforcement ratio. Using lightweight aggregate in concrete is advantageous to the dynamic stiffness of R.L.C. beam. Enhancement of concrete strength and increase of reinforcement ratio will lead to increase of the stiffness degradation of beam. The energy dissipation of R.L.C beam, similar to R.C. beam, increase with the increase of tension reinforcement ratio. The energy dissipation of unit load cycle for smaller tension reinforcement ratio is relatively less than that of beam with higher reinforcement ratio.

• 한국강구조학회 논문집
• /
• 제14권3호
• /
• pp.463-470
• /
• 2002

TEC-BEAM System은 구조용 CT형강, PC 콘크리트 그리고 현장타설콘크리트 슬래브로 이루어진 합성보이다. 이 시스템은 단순보에 대한 휨 및 전단실험을 수행하였고 우수한 거동을 보였다. 그러나 현장적용을 위해서는 TEC-BEAM과 RC 기둥 강접합 상세개발이 필요하다. 이 접합부는 TEC-BEAM의 하부에 발생하는 힘을 기둥에 전달하기 위한 매캐니즘을 발생해야만 한다. 그래서 TEC-BEAM의 단면이 증대되어 TEC-BEAM 플랜지 하부로 철근이 배근되는 접합부를 개발하였다. 본 논문에서는 제안된 시스템의 구조적 성능 평가를 위해 2개의 실험체에 대하여 실험하였다. 실험변수는 철근의 정착길이 즉, 증대된 단면의 길이이며, 실험결과 제안된 시스템은 우수한 접합부를 구조 성능을 가지고 있음을 확인할 수 있다.

• 한국시뮬레이션학회논문지
• /
• 제28권2호
• /
• pp.81-88
• /
• 2019

능동배열안테나는 원전계에 있는 표적과 지형 등을 탐지/추적하기 때문에 개발 간 항공기 탑재 전 시험 수행을 위해 원전계 거리 조건을 만족하게 하는 수십 미터 이상의 지상 시험장이 필요하다. 따라서 빔 조향, 표적, 클러터 및 재밍 등의 시험 수행을 위해 지상에서 높은 곳에 실험실을 구축하는 야외 실험장을 구축하는 것이 일반적이다. 하지만 야외 실험장은 주변 지형, 날씨, 외부 신호등으로 인해 시험에 영향을 받으며, 시간/공간/비용적인 제약사항이 많다. 이러한 문제를 해결하기 위해 근전계에서 빔을 집속 시키는 이론적인 방안이 제시되었지만, 이를 실험실 환경으로 구축하기 위해서는 AESA 레이다 하드웨어의 변화를 초래한다. 본 논문에서는 관련 하드웨어와 소프트웨어의 변화 없이 AESA 레이다를 구성하는 안테나 송수신 모듈의 편차를 보정하기 위해 단일 LUT를 이용해 근전계의 빔 집속을 구현하는 기법을 제안한다. 제안한 기법은 원전계 실험 환경 및 다중 LUT를 이용한 근전계 빔 집속 구현 기법보다 실험 비용을 최소화하면서도 유사한 실험 결과를 도출할 수 있는 장점이 있다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권6호
• /
• pp.235-244
• /
• 2021

본 연구에서는 한계상태설계법에 기반한 교량 평가법을 개발하기 위하여, 공용 중인 교량의 실측실험을 반영하여 적용성을 분석하였다. 예제 PSC Beam 실 교량의 부재 실험 결과로부터 부재의 시험강도를 구하였으며, 재료 시험값으로부터 추정된 통계특성을 적용하여 산정된 저항강도와 시험강도를 비교하였다. 부재의 시험강도와 재료의 변동성을 고려한 저항강도는 동등한 수준으로 계산되어 실측실험의 적합성이 검증되었다. 차량재하시험으로부터 응답보정계수와 동적충격계수를 계산하였으며, 실측실험 결과를 반영한 내하율을 적용하여 현행 교량 평가법과 한계상태설계법 기반으로 산정된 내하율을 비교하였다. 재료 시험값의 통계특성으로부터 추정된 부재 저항강도의 통계특성을 적용하여 실 교량의 신뢰도지수를 계산하였다. 설계기준 개발에 적용한 저항강도 통계특성으로 구한 신뢰도지수보다 실측실험의 통계특성을 적용하는 경우 더 큰 값의 신뢰도지수를 얻었다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.929-931
• /
• 2006

In this experiment, we have investigated that the transported space charge between sub-pixels in AC-plasma cell discharge. The test pulse 30 V, $5{\mu}s$ was applied to the address electrodes of neighbor cells of discharge occurred cells. And we have measured the transported space charge between sub-pixels in accordance with the various last sustain pulse widths t(time gap between the rising edges of sustain and test pulses) of 0.2 to $3{\mu}s$. It was observed that the peak value of transported space charge has been shown to be 21.5pC at $1.0{\mu}s$. And the IR peak value have been occured after $0.51{\mu}s$ with respect to sustain voltage.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.378-383
• /
• 2004

Bogie is the connection device between carbody and wheel. It is the core part that exert a important effect on the passenger safety and running safety. Bogie largely consist of bogie frame, suspension, brake, wheel set. Static and Dynamic load have acted on it complexly. So when the bogie is designed, finite element method, static load test, fatigue test running test should be considered. Some bogie frame of high speed railway freight car have the problem. It's end beam was cracked. The crack of the end beam have a bad effect on brake system. ROTEM co. made an improved end beam and applied one set to freight car. this report showed the vibration characteristic which was compared conventional bogie to improved bogie for running safety.