• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권1호
• /
• pp.62-69
• /
• 2000

The strip tension as well as the line speed should be controlled tightly for the quality of products and productivity of the continuous strip processing line. In this paper, a new tension control algorithm with tension observer is proposed using observed tension as regulator feedback. The tension observer is based on the torque balance of a roller stand including the acceleration torque. Using this estimated tension, new tension controller can be constructed with faster dynamic response in case of line speed acceleration or deceleration. The proposed scheme needs no additional hardware because the inputs of observer, current and speed, are already being monitored by the motor drive system. Through the simulations and experiments with laboratory set up, performances fo conventional schemes and proposed one are compared. The results show the effectiveness of the proposed tension controller.

• 전자공학회논문지SC
• /
• 제47권6호
• /
• pp.58-63
• /
• 2010

본 논문에서는 롤투롤 프린팅 공정을 위한 분산 처리 장력 관측 방법을 제안한다. 제안된 분산 처리 장력 관측기는 최소 차수 관측기 이론을 이용하여 설계된다. 제안된 방법은 인접 공정 영역의 속도와 장력 정보를 바탕으로 해당 공정 영역의 장력을 관측하는 특성을 가지고 있어 분산 제어 구조에 사용이 가능하다. 또한 제안된 방법은 슬라이딩 모드를 채용하여 모델 변동에 대해서도 효과적인 추정 성능을 갖는다.

• 동력기계공학회지
• /
• 제12권1호
• /
• pp.72-79
• /
• 2008

This paper designs a looper-tension controller for mass-flow stabilization in hot strip finishing mills. By Newton's 2nd law and Hooke's law, nonlinear dynamic equations on the looper-tension system are firstly derived, and linearized by a linearization algorithm using a Taylor's series expansion. Moreover, a tension calculation model is obtained from the nonlinear dynamic equations which is called as a soft sensor of strip tension between two neighboring stands. Next, a looper-tension servo controller is designed by an ILQ(Inverse Linear Quadratic optimal control) algorithm, and it is combined with a minimal disturbance observer which to attenuate speed disturbances by AGC and operator interventions, etc.. Finally, it is shown from by a computer simulation that the proposed ILQ controller with a disturbance observer is very effective in stabilizing the strip mass-flow under some disturbances, moreover it has a good command following performance.

• 전기전자학회논문지
• /
• 제11권4호
• /
• pp.213-218
• /
• 2007

We consider a web transport system. The objective of this paper is to design the output feedback controller such that the controller can track a desired tension and processing speed on web transport system. We propose the new design method using observer and feedback linearization technique. The proposed method use a nonlinear feedback to transform to linear system and high gain observer to estimate the state value. We show that the proposed controller can achieve the control object using only output. We show a performance of controller via the simulation.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권10호
• /
• pp.701-707
• /
• 2000

This paper proposes a tension control to compensate friction loss using on-line friction torque observer for a continuous strip processing line. Friction loss of roller results in significant deviation of strip tension, accordingly it has an influence on the operation of other adjacent rolls. To avoid tension variation of the strip, a friction torque observer is designed in adjacent roll, which operates in speed control mode. The observed torque is added to the torque limit reference of the pay-off reel for on-line compensation of both friction loss and acceleration/deceleration torque at the same time. The simulation and experimental results show improvement of tension control performance by the proposed friction compensation method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1096-1098
• /
• 2000

This paper proposes a tension control to compensate friction loss using on-line friction torque observer for a continuous strip processing line. Friction loss of roller results in significant deviation of strip tension. accordingly it has an influence on the operation of other adjacent rolls. To avoid tension variation of the strip, a friction torque observer is designed in adjacent roll, which operates in speed control mode. The experimental results show improvement of tension control performance by the proposed friction compensation method.

• 대한기계학회논문집A
• /
• 제36권2호
• /
• pp.237-244
• /
• 2012

이 논문은 목표치 정형화 필터와 외란관측기를 활용하여 연속 냉간압연 시스템의 스트립 두께 및 장력에 대한 2-자유도 최적 제어기 설계에 관한 연구를 수행한다. 먼저 게이지 미터식과 후크 법칙을 이용하여 스트립 두께 및 장력에 관한 동적모델을 각각 구축한다. 다음에는 동적모델을 기반으로 2-자유도 제어기를 설계한다. 여기서 피드포워드 제어기는 목표치 정형화 필터와 외란 관측기를 활용한 제어기로 구성되며, 피드백 제어기는 역 최적 제어기로 설계된다. 끝으로 컴퓨터 시뮬레이션을 통하여 이 논문에서 제안한 2-자유도 최적 제어기가 연속 냉간압연 시스템의 기존 제어기보다 스트립 두께 및 장력에 대한 목표치 추종성능과 외란 제거성능이 매우 우수함을 보인다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2620-2622
• /
• 1999

To control a continuous processing line, it is necessary to take the entire system into account. In this paper observers to estimate the line tension are discussed. Considering a tension as a external disturbance, a closed loop observers are designed. It becomes clear that the proposed tension control scheme has high accuracy performance and simplicity.

• 제어로봇시스템학회논문지
• /
• 제14권9호
• /
• pp.956-962
• /
• 2008

This paper is devoted to yarn tension control problem in winding machines. The passive take-up unit is replaced by active one with ADRC(Active Disturbance Rejection Control) and it was compared with the method using conventional PD(Proportional-Derivative) controller. The main part of ADRC is ESO(Extended State Observer) which continuously estimates nonlinearities of the system, such as intrinsic nonlinearity, external disturbance and sensor noise. Then the estimated nonlinearity is used to compensate the real one, thus making controlled system linear. A number of experiments have been conducted in order to verify the performance of the original winding system to the modified one. Experiments have shown improved efficiency of the system with adopting active yarn tension control. Experimental results show that the ADRC achieves a better tension response than PD controller and is robust to parameters variation.

• 국제물리치료학회지
• /
• 제10권4호
• /
• pp.1897-1902
• /
• 2019

Background: Tension-type headaches, which make up the highest proportion of headaches, are prone to develop into chronic tension-type headaches (CTTH). The characteristic of CTTH in patients is that the active myofascial trigger point (ATrP) which causes pain in the muscles of the back of the head is increased, compared to the normal headache and moves the head position forward. Objective: The aim of this study was to investigate the effects of myofascial release (MFR) and posture correction in effectively improving neck function and sleep quality in the symptoms of CTTH patients. Design: Observer-blind study Methods: To reduce ATrP, MFR was applied and exercise was also applied to correct posture. The subjects of this study were 48 individuals randomly divided into three groups; The MFR group using the MFR technique; The MFR with exercise group subject to both the MFR technique and forward head position correction exercises (MFREx), and the control group. MFR and MFREx groups were given the relevant interventions twice a week for four consecutive weeks, and went through the number ATrPs, range of motion (ROM) of neck, Neck Disability Index (NDI) and the Pittsburgh Sleep Quality Index (PSQI) before and after the intervention. A physical therapist, who was fully familiar with the measuring methods of the equipment, was the measurer and not aware of the target's condition was blinded to take measurements only before and after intervention. Results: There was a significant improvement in the ATrP, Neck ROM, NDI and PSQI in the group of patients to whom the MFR technique and MFREx were applied. MFREx was more effective in increasing neck mobility. Conclusions: According to this study, the application of MFR is effective in improving neck movement and sleep quality in chronic tension headache patients.