• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.1
• /
• pp.1-9
• /
• 1997

The variation of the mechanical properties and the formation of retained austenite with heat treatment conditions in austempered Si bearing carbon steels has been investigated. In the case of a steel containing 0.35C-1.48Si-0.95Mn, it has been found that a feather shape bainite structure of lath are obtained under a isothermal treated condition at just below the Ms temperature, and the martensite, bainitic ferrite and retained austenite of second phase particles on the ferrite matrix for a isothermal treated steels after intercritical annealing are precipitated in a linked shape. The retained austenite with $2{\mu}m$ size induced as TRIP is found to increase with increasing the formation rate of retained austenite for the intercritical annealing and high Si containing steels. The tensile strength is increased as austempering temperature increases in all isothermal treatment temperature, whereas the elongation is shown to roughly decrease as the tensile strength increases. The values of tensile strength-elongation balance have showed a marked dependence upon the elongation rather than the tensile stregth, and their values are increased for high Si containing steels and intercritical annealing condition. The most optimum result has been shown to be the tensile stregth-elongation balance of $2882.4kgf/mm^2.%$ and the elongation of 33.3% for a "B" steel in the heat treating temperature range of $780{\sim}370^{\circ}C$.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.20 no.4
• /
• pp.73-82
• /
• 2018

This research investigated the mechanical properties of the 4 different types of $3{\times}3$ cable stitches on weft knitted fabrics. The 4 kinds of cable-stitch fabrics were knitted under the same knitting conditions, then the mechanical properties, such as tensile strength, elongation, stiffness, etc. were measured according to the Korean Industrial Standards (KS K 0642). The knitting time for the sample produced by the knitting process 1 was the shortest among the 4 different types of samples. It means that the knitting process 1 would have benefits of higher productivity if there is no yarn breakage during the knitting of the cable stitches. In the test for tensile strength, the samples produced by knitting processes 3 and 4 have tensile values of approximately 8~11% higher than the sample produced by knitting process 1. The test for elongation also shows that the samples produced by knitting processes 3 and 4 have up to 18% higher elongation values than the sample produced by knitting process 1. On the other hand, the stiffness test showed no significant difference between the 4 samples. This study is expected to increase the competitiveness of the local knitting industry as a result of providing basic data on the mechanical properties of special knitted stitches, such as cable stitches.

• Journal of Power System Engineering
• /
• v.12 no.3
• /
• pp.72-77
• /
• 2008

This study was investigated to know the effect of Cu addition on austempered ductile cast iron at various temperatures and times. Test results showed that the volume fraction of retained austenite and the carbon contents of retained austenite showed the greatest value at $400^{\circ}C$. Also, in case of specimens having more Cu contents, the volume fraction of retained austenite and the carbon contents of retained austenite showed the lower value. After austempering treatment, tensile strength and Impact value increased, but elongation decreased. With increasing austempering treatment temperature, tensile strength, elongation, and impact value decreased. In case of specimen having more Cu contents, tensile strength showed the higher value, but elongation showed the lower value. Damping capacity was decreased by austempering treatment and was not affected on austempering temperature and time. In case of specimen having more Cu contents, damping capacity showed the higher value.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.5
• /
• pp.1248-1256
• /
• 2020

In this study, the polyurethane resin was synthesized by applying PTMG and DMBA of different composition ratios for the synthesis of water-dispersible polyurethane used in wound coating resin. The varying properties of the synthesized water-dispersible polyurethane were measured through tensile strength, elongation, and abrasion resistance analysis. As for the tensile strength measurement result according to the PTMG content, the sample with the highest reaction molar ratio was measured as 1.08 kgf/mm2 and the elongation was measured as 520%. As for the tensile strength result according to the DMBA content, the sample with the highest reaction molar ratio was measured as 0.51 kgf/mm2, and the elongation was measured as 435%. The degree of surface destruction by the abrasion resistance measurement was visually confirmed through SEM.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.06a
• /
• pp.121-130
• /
• 1998

In order to analyze the forming characteristics of laser welded tailored blanks, laser welded blanks of different thickness and strength combinations were prepared and tensile, stretching, stretch flanging and deep drawing tests were done. The tensile elongation perpendicular to the weld line, stretching and stretch flanging formability decreased with increasing the deformation restraining force (strength ${\times}$ thickness) ratio between two welded sheets. The tensile elongation along weld line reached a value above 90% of the single sheet's elongation. Stretch flanging formability was reduced to approximately 10% of the single sheet value when the deformation restraining force ratio between two welded sheets was increased to two. Weld line movement of deep drawing test specimens was also affected by the strength ratio of the combined sheets, the weld line location and forming conditions. In all forming modes of tailored blanks, excessive weld line movement resulted from strain concentrations at the weaker sheet and resulted in fracture of the weaker side.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.2
• /
• pp.109-120
• /
• 1997

Microstructure and mechanical properties of Fe-Si-Mn-P high strength steel sheet have been investigated by controlling the cooling rate. Bainite and ferrite were obtatined by annealing in the ferrite pluse austenite region, and ferrite and austenite were obtatined after annealing in the fully austenite region. Ferrite and pearlite were obtained when the cooling rate was controlled from the annealing temperature above $760^{\circ}C$ and bainite showed with increasing cooling rate, however below $760^{\circ}C$ ferrite and bainite were obtained. Tensile strengths and hardness nearly unchanged with increasing cooling rate after control the cooling rate from the temperature above $760^{\circ}C$, while tensile strengths increased and elongation decreased with increasing cooling rate when the cooling rate was controlled from the tempeature below $760^{\circ}C$. Without regard to annealing temperature, tensile strength increased and elongation decreased with increasing cooling rate. Tensile strengths and elongation values heat treated in the ferrite plus austenite region were higher than those in the fully austenite region. Retained austenite and strength-elongation balance showed the maximum value at $780^{\circ}C$ and decreased with increasing annealing temperature. Strength-elongation balance value was controlled by the retained austenite.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.410-413
• /
• 2008

In this study, we compare the mechanical properties of forged and machined bushings for an excavator track chain. The manufacturing process is explained in detail together with the procedure of making the specimens. The longitudinal tensile strength and elongation and the radial ring compression strength are measured for this comparison. It has been shown that the forged is much better than the machined with regard to both longitudinal tensile strength and radial ring compression strength but that both are the same in terms of longitudinal elongation.

• Korean Journal of Metals and Materials
• /
• v.48 no.7
• /
• pp.598-604
• /
• 2010

Tensile tests are widely used for evaluating mechanical properties of materials including flow curves as well as Young's modulus, yield strength, tensile strength, and yield point elongation. This research aims at analyzing the plastic flow behavior of high strength steels for automotive bodies using the finite element method in conjunction with the viscoplastic model considering the yield point elongation phenomenon. The plastic flow behavior of the high strength steel was successfully predicted, by considering an operating deformation mechanism, in terms of normalization dislocation density, and strain hardening and accumulative damage of high strength steel using the modified constitutive model. In addition, the finite element method is employed to track the properties of the high strength steel pertaining to the deformation histories in a skin pass mill process.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.15 no.3
• /
• pp.33-40
• /
• 2013

This paper focused on investigating the seam strength by cutting direction depending on the fabrics and weave by comparing the tensile strength and elongation of bias, warp and weft of 4 kinds of find cotton fabrics and combining 6 kinds of seam cutting directions. The cutting directions are selected the warp direction, weft direction and 45-degree bias direction. Then, three kinds of directions, the warp/warp direction, the weft/weft direction and the bias/bias directions, and the three different kinds of directions, the warp/weft direction, the warp/bias direction and the weft/bias directions, were finally selected. The results are as follows: The tensile strength of all fabrics was higher in the order of warp, bias and weft direction and tensile elongation was higher in the order of bias, warp and weft direction in almost all fabrics. 100's and 150's cotton fabrics showed the highest seam strength when they were cut in the bias/bias direction. The seam strength of the fabrics cut in the same direction was the highest in the fabrics cut in the bias/bias direction. Four kinds of fabrics demonstrated the similar seam strength. However, for the seam strength of fabrics cut in the different directions, 100's cotton fabrics had the difference of seam strength by direction and weave, but 150's cotton fabrics didn't have any difference in seam strength by direction and weave. As described above, the seam strength was influenced by the cutting direction of fabrics. Accordingly, the seam strength can be improved by changing the cutting direction of seam when making the clothing.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.4
• /
• pp.295-304
• /
• 1998

The effects of retained austenite and carbon content in the retained austenite on the tensile strength-elongation balance and spot weldability of TRIP high strength steel sheet have been investigated. The retained austenite of granular type increased with increasing intercritical annealing and austempering temperature, and film type was increased with the increase of austempering time. The volume fraction of retained austenite increased with decreasing intereritical annealing temperature, and the maximum value was obtained at austempering temperature of $400^{\circ}C$. The values of tensile strength-elongation balance increased with decreasing intercritical annealing temperature and maximum value was obtained at austempering temperature of $400^{\circ}C$. The maximum value of tensile strength-elongation balance was obtained at a retained austenite content of about 12%. Tensile shear strength of the specimens with retained austenite was higher than that of the normalizing specimens. With increasing welding current and time, the tensile shear strengh and nugget diameter increased, while nugget thickness showed the peak value and then decreased. The optimum range of welding condition at the given welding pressure of 350kgf was 7~11kA and 10~15 cycles.