• Structural Engineering and Mechanics
• /
• v.77 no.1
• /
• pp.1-17
• /
• 2021

The influence of prestress force on the fundamental frequency and static deflection shape of uncracked Prestressed Concrete (PC) beams with a parabolic bonded tendon was examined in this paper. Due to the conflicts among existing theories, the analytical solutions for properly considering the dynamic and static behavior of these members is not straightforward. A series of experiments were conducted for a total period of approximately 2.5 months on a PC beam made with high strength concrete, subsequently and closely to the 28 days of age of concrete. Specifically, the simply supported PC member was short term subjected to free transverse vibration and three-point bending tests during its early-age. Subsequently, the experimental data were compared with a model that describes the dynamic behavior of PC girders as a combination of two substructures interconnected, i.e., a compressed Euler-Bernoulli beam and a tensioned parabolic cable. It was established that the fundamental frequency of uncracked PC beams with a parabolic bonded tendon is sensitive to the variation of the initial elastic modulus of concrete in the early-age curing. Furthermore, the small variation in experimental frequency with time makes doubtful its use in inverse problem identifications. Conversely, the relationship between prestress force and static deflection shape is well described by the magnification factor formula of the "compression-softening" theory by assuming the variation of the chord elastic modulus of concrete with time.

• Steel and Composite Structures
• /
• v.19 no.1
• /
• pp.43-58
• /
• 2015

There are many studies on the optimization of steel trusses in literature; and, a large number of them include a shape optimization. However, only a few of these studies are focused on the prestressed steel trusses. Therefore, this paper aims to determine the amounts of the material and cost savings in steel plane trusses in the case of prestressing. A parallel-chord simply supported steel truss is handled as an example to evaluate the used approach. It is considered that prestressing tendon is settled under the bottom bar, between two end supports, using deviators. Cross-sections of the truss members and height of the truss are taken as the design variables. The prestress losses are calculated in two steps as instantaneous losses and time-dependent losses. Tension increment in prestressing tendon due to the external loads is also considered. A computer program based on genetic algorithm is developed to solve the optimization problem. The handled truss is optimized for different span lengths and different tendon eccentricities using the coded program. The effects of span length and eccentricity of tendon on prestressed truss optimization are investigated. The results of different solutions are compared with each other and those of the non-prestressed solution. It is concluded that the amounts of the material and the cost of a steel plane truss can be reduced up to 19.9% and 14.6%, respectively, by applying prestressing.

• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.3
• /
• pp.555-561
• /
• 2024

This paper derives material properties of steel bars that simulate the distribution of stress and strain of prestressed tendons used in Prestressed concrete(PSC) girders and presents an optimal material model. ABAQUS software was used to establish the 3D solid model of the PSC girder and strand wire rope for a PS(Prestressed) tendon. Then the model of steel wire rope was imported into the Isight interface plugin directly through the ABAQUS and the Data Matching. In ABAQUS, the contact pairs were established, the models were meshed, the constraints were applied to solve the finite element model and an axial tension of 0.5m/s was loaded to analyze the stress and deformation distributions in the normal working range of the PS strand wire rope. In Data Matching, classical experimental data is fitted to the optimal material properties through finite element analysis and multi-objective optimization. The results show that the steel bar with optimal material properties presents a similar linear area and stress distribution with the PS tendon.

• Structural Engineering and Mechanics
• /
• v.62 no.5
• /
• pp.595-606
• /
• 2017

During their life span, post-tensioned concrete structures may be exposed to thermal loads. Therefore, there has been a growing interest in research on the advanced analysis and design of post-tensioned concrete slabs subjected to thermal loads. This paper investigates the structural behaviour of post-tensioned one-way spanning concrete slabs. A nonlinear finite element model for the analysis of post- tensioned unbonded and bonded concrete slabs at elevated temperatures was developed. The interface between the tendon and surrounding concrete was also modelled, allowing the tendon to retain its profile shape during the deformation of the slab. The load-deflection behaviour, load-force behaviour in the tendon, and the failure modes are presented. The numerical analysis was conducted by the finite element ANSYS software and was carried out on two different one-way concrete slabs chosen from literature. A parametric study was conducted to investigate the effect of several selected parameters on the overall behavior of post-tensioned one-way concrete slab. These parameters include the effect of tendon bonding, the effect of thermal loading and the effect of tendon profile. Comparison between uniform thermal loading and nonuniform thermal loading showed that restrained post tensioned slab with bottom surface hotter has smaller failure load capacity.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.93-98
• /
• 2001

This study is to develop the end anchorage of external steel reinforcement of RC slab bridges. External prestress method using the existing steel is that When the anchorage is installed in slab end, a plenty of anchor bolts were required because the only tangential stress of anchor bolt received a tendon force. Then, for this reason, the wide end anchorage was required and the shape was complicate. But this reinforcement method using method that inserts anchor key at concrete surface cut a groove gets big internal force comparing to the anchorage using existing anchor bolt. Furthermore, the number of anchor bolt for installing apparently will be reduced, and the operation will be convenient because a small anchorage of a simple shape will be received a great tendon force

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.1009-1014
• /
• 2001

This study is to develop the end anchorage of external steel reinforcement of RC slab bridges. External prestress method using the existing steel is that When the anchorage is installed in slab end, a plenty of anchor bolts were required because the only tangential stress of anchor bolt received a tendon force. Then, for this reason, the wide end anchorage was required and the shape was complicate. But this reinforcement method using method that inserts anchor key at concrete surface cut a groove gets big internal force comparing to the anchorage using existing anchor bolt. Furthermore, the number of anchor bolt for installing apparently will be reduced, and the operation will be convenient because a small anchorage of a simple shape will be received a great tendon force.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1285-1288
• /
• 1997

The basic technology of virtual reality can be described as the cognition of the condition change in virtual world by stimulating the visual, auditory, kinesthetic and tactile sensation. Among these, the kinesthetic and tactile sensation is one of the most important things to recognize the interaction. In this paper, it is addressed the haptic device which help the human feel the sense of the operator, and is designed in modular type to expand for five fingers later. the haptic device is driven by tendon and ultrasonic motors located in the wrist part. Each joint is actuated by coupled tendons and adopts more actrator by one than the number of the joints, called 'N+1 type'. The haptic device adopts metamorphic 4-bar linkage structure and the length of linkages, shape and the location of joint displacement sensor are optimized through the analysis.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.6
• /
• pp.63-70
• /
• 2008

Strengthening method of steel-concrete composite bridges using external tendons has been found as one of the most effective techniques of reinforcement and its application is increasing. In this paper, experimental test was carried out to show the effects on the yield loading and ultimate loading of steel-concrete composite beams strengthened with various configurations of external tendons. Quantitative analysis is carried out to evaluate the effects of experimental variables such as tendon force, deviator, tendon eccentricity and the shape of strands.

• Journal of Korean Foot and Ankle Society
• /
• v.13 no.2
• /
• pp.193-196
• /
• 2009

The first metatarsophalangeal joint injury is common in professional soldiers and athletes. But this was rarely reported. A professional soldier has varus instability in the first metatarsophalangeal joint due to hyperextension. In the MR Imaging, weavy appearance in lateral collateral ligament and high signal change in plantar plate was shown. So he has surgical treatment using reconstructive procedure. At first, $4^{th}$ extensor digitorum longus tendon was splitted longitudinally and harvested, second triangular shape reconstruction on lateral joint line was done using harvested tendon. One year later, fifteen degrees was limited compared with intact side. Reconstruction using $4^{th}$ extensor digitorum longus tendon in traumatic dynamic hallux varus was good method.

• Korean Journal of Environmental Biology
• /
• v.37 no.3
• /
• pp.343-350
• /
• 2019

Cyllorhynchites ursulus drills holes in acorn and cuts branches with mandibles. To understand this special behavior, we observed the mouthpart of this species using several microscope methods. The stereoscopic microscope used in this study shows that the adductor tendon is thicker than the abductor tendon which confirms that mandibles exert more force pulling inwards than pushing outwards. Also, the shape and position differences were observed using an optical microscope. We found differences of the shape, position, and movement of mandibles among C. ursulus, Curculio sikkimensis and Paracycnotrachelus longiceps by way of observation using SEM. The width of the adductor tendon and the abductor tendon of males of the C. ursulus species was 32.87 ㎛, and 53.83 ㎛, respectively. And, the width of females was 40.81 ㎛ and 75.55 ㎛, respectively. Based on a variety of observations and analyses, we found that the unusual behavior of C. ursulus is deeply related to the morphological features, and these features could be applied to biomimicry.