• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 학술대회 논문집
• /
• pp.257-260
• /
• 2003

Bi-2223 tape is one of the most widely used HTS tapes for power application. This paper presents the basic properties such as temperature and resistivity rise of the Bi-2223 tape which is exposed to the over current. Temperature and resistivity were measured by E-type thermocouple and voltage taps. Results of the measurement showed that rise of voltage depended on the magnitude of the over current until several times of the rated current. When the current largely exceeded the rated current, rise of voltage depended on the magnitude of the resistivity of the Ag matrix because temperature of the matrix increased to a great extend.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.560-567
• /
• 2011

Wheel and rail wear is a fundamental and complicate problem in railway field. The life of railway is usually limited by wear. The wheel surface is subjected to high normal and tangential contact stress. The removal of material from the surface by wear is function of the sliding and contact stress. In the present paper, the wear characteristic depended on slip rate, contact pressure and temperature are investigated and is used to twin disc tester. The result shows that the wear in wheel-rail interface is remarkably depended on slip rate and contact pressure.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1000-1007
• /
• 2011

Wheel and rail wear is a fundamental and complicate problem in railway field. The life of railway is usually limited by wear. The wheel surface is subjected to high normal and tangential contact stress. The removal of material from the surface by wear is function of the sliding and contact stress. In the present paper, the wear characteristic depended on slip rate, contact pressure and temperature are investigated and is used to twin disc tester. The result shows that the wear in wheel-rail interface is remarkably depended on slip rate and contact pressure.

• 한국환경과학회지
• /
• 제15권7호
• /
• pp.635-642
• /
• 2006

Present study evaluated the low-temperature destruction of n-hexane and benzene using mesh-type transition-metal platinum(Pt)/stainless steel(SS) catalyst. The parameters tested for the evaluation of catalytic destruction efficiencies of the two volatile organic compounds(VOC) included input concentration, reaction time, reaction temperature, and surface area of catalyst. It was found that the input concentration affected the destruction efficiencies of n-hexane and benzene, but that this input-concentration effect depended upon VOC type. The destruction efficiencies increased as the reaction time increased, but they were similar between two reaction times for benzene(50 and 60 sec), thereby suggesting that high temperatures are not always proper for thermal destruction of VOCs, when considering the destruction efficiency and operation costs of thermal catalytic system together. Similar to the effects of the input concentration on destruction efficiency of VOCs, the reaction temperature influenced the destruction efficiencies of n-hexane and benzene, but this temperature effect depended upon VOC type. As expected, the destruction efficiencies of n-hexane increased as the surface area of catalyst, but for benzene, the increase rate was not significant, thereby suggesting that similar to the effects of the re- action temperature on destruction efficiency of VOCs, high catalyst surface areas are not always proper for economical thermal destruction of VOCs. Depending upon the inlet concentrations and reaction temperatures, almost 100% of both n-hexane and benzene could be destructed, The current results also suggested that when applying the mesh type transition Metal Pt/SS catalyst for the better catalytic pyrolysis of VOC, VOC type should be considered, along with reaction temperature, surface area of catalyst, reaction time and input concentration.

• 한국주조공학회지
• /
• 제37권6호
• /
• pp.199-206
• /
• 2017

In this study, the variations of microstructures and tensile properties of Ti-(44-54)at.%Al binary alloys were investigated. The heat-treated microstructure depended greatly on their solidification structure and annealing temperature. We measured the variations of volume fractions of primary and secondary lamellar structure as a function of the heat treatment temperature in a Ti-47at.%Al alloy. The variation of ductility as a function of Al content was in good agreement with the change of fracture mode in the tensile fracture surface. It can be inferred that the variations of yield stress and hardness of ${\gamma}$ phase in a single ${\gamma}$-phase field region are enhanced by anti-site defects created by deviations from the stoichiometric composition. In a Ti-47at.%Al alloy within the (${\alpha}_2+{\gamma}$) two-phase field, the yield stress tended to be the maximum at a near equal volume fraction of lamellar and ${\gamma}$ grains. The ductility depended sensitively on the overall grain size and Al content. The calculation of fracture strain using Chan's model indicated that the change of ductility as a function of annealing temperature was primarily determined by the variations in the overall grain size and lamellar volume fraction.

• 한국세라믹학회지
• /
• 제32권6호
• /
• pp.748-760
• /
• 1995

Pyroelectric properties, figure of merits, and the other properties of the Pb(Zn1/3Nb2/3)O3-Pb(Fe1/2Nb1/2)O3 system, as expected to have excellent pyroelectric properties in the operating temperature range of pyroelectric type infrared sensor, were investigated. In the Pb(Zn1/3Nb2/3)O3-Pb(Fe1/2Nb1/2)O3 system, suppression of the pyrochlore phase depended on sintering condition, as like sintering temperature, holding time, sintering atmosphere. The specimen, sintered by the same composition atmosphere powder at 105$0^{\circ}C$ for 1.5h, possessed the best physical property. It was found that the piezoelectric parameters were mainly depended on the amount of spontaneous polarization and then the 0.2PZN-0.8PFN showed the best pyro- and piezoelectric properties. In terms of the experimental method, two pyroelectric-testing methods, i.e. static and dynamic methods, had a same tendency. Also the result of pyroelectric testing by the static method indicated that the diffuse phase transitiion resulted in the temperature difference of phase transition between dielectric constant and pyroelectric coefficient.

• Journal of Magnetics
• /
• 제12권1호
• /
• pp.45-48
• /
• 2007

[ $Co_{100-X}Zr_X$ ] (x=10-40) alloys were prepared by using a mechanical alloying technique. Phase constitution of the crystallised material depended on the annealing temperature. The $Co_{82}Zr_{18}$ alloy crystallised at lower temperature around $550^{\circ}C$ consisted of $Co_{23}Zr_6$, $Co_5Zr$ and fcc-Co phases, while the alloy crystallised at higher temperature around $800^{\circ}C$ consisted of $Co_{23}Zr_6$ and fcc-Co phases. Phase constitution of the crystallised material also depended on the chemical composition of the alloy. The material with lower Zr content less than 10 at% Zr consisted of $Co_{23}Zr_6$ and fcc-Co, and the material with higher Zr-content over 30 at% consisted of $Co_2Zr$ phase. The material containing 15-20 at% Zr consisted of $Co_{23}Zr_6$, $Co_5Zr$ and fcc-Co. Only the material containing $Co_5Zr$ phase exhibited substantial coercivity, and it was confirmed that coercivity in the mechanically alloyed Co-Zr alloy was originated from the $Co_5Zr$ phase.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권7호
• /
• pp.347-351
• /
• 2004

The $ZnNb_2O_{6}$ ceramics with CuO(1, 3, 5wt%) were prepared by the conventional mixed oxide method. The ceramics were sintered at the temperature of $950^{\circ}C$∼$1075^{\circ}C$ for 3hr in air The structural properties and the microwave dielectric properties of $ZnNb_2O_{6}$ ceramics were investigated with sintering temperature and the addition of CuO. Increasing the addition of CuO, the peak of second phase($Cu_3Nb_2O_{8}$) was increased. The grain size of the $ZnNb_2O_{6}$ ceramics with CuO was increased with CuO addition at same temperature. The dielectric constant of $ZnNb_2O_{6}$ ceramics with CuO was increased with sintering temperature and CuO addition. While the quality factor of the $ZnNb_2O_{6}$ ceramics with lwt% CuO depended on sinterability, the quality factor of $ZnNb_2O_{6}$ with 3wt% and 5wt% CuO depended on second Phase due to the CuO addition. The optimum dielectric Properties of $\varepsilon$$_{r}$ = 21.73 Q${\times}$f = 19,276 were obtained from the condition of 3wt% CuO addition and sintering temperature of $1025^{\circ}C$(3hr).

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2009년도 정보통신설비 학술대회
• /
• pp.391-394
• /
• 2009

In this paper, achieved rise temperature distribution about degradation phenomenon of 2 MVA distribution mold transformer using finite element method (FEM). Usually, life of transformer is depended on temperature distribution of specification region than thermal special quality of transformer interior. Specially, life of transformer by decline of dielectric strength decreases rapidly in case rise by strangeness transformer interior hot spot temperature value permits. Because calculating high-voltage winding and low-voltage winding of mold transformer and Joule's loss of core for improvement these life, forecasted heat source, and high-voltage winding and low-voltage winding of mold transformer and rise temperature distribution of core for supply of electric power and temperature distribution of highest point on the basis of the result Also, calculated temperature rise limit of mold transformer and permission maximum temperature using analysis by electron miracle heat source alculate and forecasted rise temperature distribution by heat source of thermal analysis with calculated result.

• 한국분말재료학회지
• /
• 제11권5호
• /
• pp.363-368
• /
• 2004

In the present study, the focus is on the analysis of the effect of the mold dimensions on the temperature distribution of a die during plasma activated sintering. The temperature distribution of a cylindrical mold with various dimensions was measured using K-type thermocouples. The temperature homogeneity of the die was studied based on the direction and dimensions of the die. A temperature gradient existed in the radial direction of the die during the plasma activated sintering. Also, the magnitude of the temperature gradient was increased with increasing sintering temperature. In the longitudinal direction, however, there was no temperature gradient. The temperature gradient of the die in the radial direction strongly depended on a ratio of die volume to punch area.