• Journal of the Korean Magnetics Society
• /
• v.25 no.2
• /
• pp.47-51
• /
• 2015

To achieve a high tunneling magneto resistance (TMR) of sputtered magnetic tunnel junctions (MTJs) with an MgO barrier, the annealing process is indispensable. The structural and compositional changes as consequences of the annealing greatly affect the spin-dependent transport properties of MTJs. Higher TMR could be obtained for MTJs annealed at higher annealing temperature. The diffusion of Ru, Mn and/or Ta in the MTJs may occur during annealing process, which is known to be detrimental to spin-dependent tunneling effect. The rapid thermal annealing (RTA) process was used for annealing the MTJs with synthetic antiferromagnets. To suppress the diffusion of Mn, Ru and/or Ta in the MTJs, the process time and temperature of RTA were minutely controlled.

• Mass Spectrometry Letters
• /
• v.5 no.1
• /
• pp.24-29
• /
• 2014

An advanced and reliable high performance liquid chromatography (HPLC)/ultraviolet detector (UV)/ion-trap time-of-flight (IT-TOF) mass spectrometry was developed for the simultaneous quantification of 19 marker compounds in Bang-poong-tong-sung-san (BPTS), a traditional oriental prescription. Various parameters affecting HPLC separation and IT-TOF detection were investigated, and optimized conditions were identified. The separation was achieved on a Capcell PAK C18 column ($1.5mm{\times}250mm$, $5{\mu}m$ particle size) using a gradient elution of acetonitrile and water containing 0.1% formic acid at a flow rate of 0.1 mL/min. The column temperature was maintained at $40^{\circ}C$ and the injection volume was $2{\mu}L$. IT-TOF system was equipped with an electrospray ion source (ESI) operating in positive or negative ion mode. The optimized electrospray ionization parameters were as follows: ion spray voltage, +4.5 kV (positive ion mode), or -3.5 kV (negative ion mode); drying gas ($N_2$), 1.5 L/min; heat block temperature, $200^{\circ}C$. Automatic $MS^n$ (n = 1~3) analyses were carried out to obtain structural information of analytes. Elemental compositions and their mass errors were calculated based on their accurate masses obtained from a formula predictor software. The marker compounds in BPTS were identified by comparisons between $MS^n$ spectra from standards and those from extracts. Moreover, the libraries of $MS^2$ and $MS^3$ spectra and accurate masses of parent and fragment ions for marker compounds were constructed. The developed method was successfully applied to the BPTS extracts and identified 17 out of 19 marker compounds in the BPTS extracts.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.3
• /
• pp.191-198
• /
• 2008

Pot life of two-component adhesives such as epoxy resin used in saturating FRP composite is defined as a certain time periods which can guarantee the bond performance and workability of epoxy resin. Therefore, adhesion procedure in strengthening RC members should be completed before chemical hardening is going on at job site. It has been known that there are two types of test method to evaluate the pot life of structural adhesive based on apparent viscosity or temperature change. This study is to verify the test methods how to assess pot life of structural adhesive for FRP composites by means of changing in apparent viscosity and means of exothermic reaction temperature proposed in existing test standards. Results of each test method were compared and analyzed, and reasonable test and evaluation method were suggested.

• Journal of Adhesion and Interface
• /
• v.5 no.3
• /
• pp.1-9
• /
• 2004

Using the methods which described in ISO 4588, ASTM D2651 and the selected literature, we investigated the best conditions of acid treatment for stainless steel and carbon steel. The acid treatments were conducted with four different acid solutions which were prepared for stainless steel and carbon steel specimen. We observed the contact angle and morphology and roughness of the metal surface and the thickness change at various treatment conditions as treatment temperature and time. Also, we investigated the characteristics of the surface aging according to air exposure after surface treatment. As a result, the optimal temperature of the acid treatment for stainless steel and carbon steel were each obtained at $83^{\circ}C$ and $63^{\circ}C$. Also, it was confirmed that the acid treatments for the metal surface were accompanied with the decrease of thickness and the change of surface morphology due to significant erosion that depend on treatment methods. And also, it was characterized that the aspect of surface aging by air exposure was highly depended on the method of acid treatment.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.25 no.4
• /
• pp.51-60
• /
• 2017

Bottom ash(BA) from coal-fired power plants is burnt and remaining ash at high temperature. Since the BA is baked at high temperature, it is considered to be the same function as the elvan. Nowadays, the demand for mortar with far infrared rays, antibacteria, antifungus, deodorization, aridity and humidity function is increasing as the materials such as Hwangtoh(yellow soil) and elvan rather than general mortar. As a result of comparing the functionality of eco-friendly bio BA mortar with that of general mortar, the far infrared ray emissivity is about $0.02{\times}10^2W/m^2$ more and the deodorization function is about 26% or more. Even in the case of humidity control, BA motors showed about 1.8 times higher than general mortar, and more than 10% higher than the "good" standards of moisture absorption and damp proofing construction materials established by the Ministry of Land, Transport and Maritime Affairs.

• Journal of Biomedical Engineering Research
• /
• v.41 no.1
• /
• pp.55-61
• /
• 2020

Recently, there have been many research on fever management using u-healthcare technology. Especially, fever of infants requires continuous monitoring of body temperature by parents. For infants between 4 weeks and under 5 years old, it is recommended to use an electronic thermometer or chemical thermometer in the axilla, or to use an infrared thermometer. However, in order to overcome the reality of not being able to waste significant time on continuous monitoring, there have been demands of patch type thermometers with the internet of things (IoT) and wireless communication technologies. Existing IoT thermometers are difficult to attach to infants' body because they do not take into account its size, and their interoperability is not guaranteed because they do not comply with standards in communication. Therefore, in this study, a patch-type thermometer with a diameter of 20 mm and a weight of 2.9 g was developed to manage the fever of infants, while it communicates wirelessly with Bluetooth Low Energy (BLE) communication protocol and complies with IEEE 11073 PHD(Personal Health Device) at the same time. We verified its performance under the requirements of thermometers regulated by the Korean Ministry of Food and Drug Safety.

• Journal of the Korean Institute of Gas
• /
• v.21 no.6
• /
• pp.81-87
• /
• 2017

SOFC(Solid Oxide Fuel Cell) is one of the high-temperature fuel cells, SOFC system and Stack has a high temperature operating Characteristics. These Characteristics cause a lot of trouble in the design of the system and selection materials, securing durability, and securing safety performance. Therefore, For Commercialization and Supply of SOFC, the development of safety performance assessment techniques and evaluation systems should go together. In this study, we analyzed the evaluation items of SOFC Safety performance standards and risk factors of the stack for design of stack safety performance evaluation system. Based on the analyzed data, the evaluation item was deducted for design of stack safety performance evaluation system. Through the results of this study, we expect to facilitate the supply of SOFC and contribute to a safe use environment.

• Journal of the Korean Chemical Society
• /
• v.36 no.3
• /
• pp.419-427
• /
• 1992

The performance of homemade thermal field-flow fractionation (ThFFF) and the optimization for separation are investigated in terms of retention parameters and selectivity using polystyrene standards. The ribbonlike channel was constructed by sandwiching two Mylar spacers between two highly polished copper bars which serve as channel walls. The hot bar was heated by two electrical cartridge heaters and the cold bar had holes through the entire length, allowing tap water as coolant to enter. It has been observed that the retention of polystyrenes increases as the temperature gradient increases. And the retention decreases as the cold wall temperature increases from 20 to $45^{\circ}C$. In comparison with size exclusion chromatography, ThFFF is more selective but has relatively low efficiency. It has been found that the plate height is proportional to the flow velocity and good estimates of polydispersities can be made directly from the ThFFF data.

• Korean Journal of Materials Research
• /
• v.24 no.1
• /
• pp.48-52
• /
• 2014

The Mg-enriched magnesium aluminum silicate (MAS) glass is known for its higher mechanical strength and chemical resistance. Among such glasses, cordierite ($Mg_2Al_4Si_5O_{18}$) is well known to have a low thermal expansion and low melting point. Polycrystalline engineering ceramics such as alumina can be strengthened by a surface modification with low thermal expansion materials. The present study involves the synthesis of cordierite by a sol-gel process and investigates the effect of glass penetration on the surface of alumina. The cordierite powders were prepared from $Al(OC_3H_7)_3$, $Mg(OC_2H_5)_2$ and tetraethyl orthosilicate by hydrolysis and condensation reaction. The cordierite powders were characterized by X-ray diffraction (XRD, Rigaku), scanning electron microscope (SEM, JEOL: JSM-5610), energy dispersive spectroscopy (EDS, JEOL: JSM-5610), and universal testing machine (UTM, INSTRON). The X-ray diffraction patterns showed that the synthesized particles were ${\mu}$-cordierite calcined at $1100^{\circ}C$ for 1 h. The shape of synthesized cordierite was changed from ${\mu}$-cordierite to ${\alpha}$-cordierite with increasing calcination temperature. Synthesized cordierite was used for surface modification of alumina. Cordierite powders penetrated deeply into the alumina sample along grain boundaries with increasing temperature. The results of surface modification tests showed that the strength of the prepared alumina sample increased after surface modification. The strength of a surface modified with synthesized cordierite increased the most, to about 134.6MPa.

• Journal of the Korean Society of Systems Engineering
• /
• v.4 no.1
• /
• pp.35-43
• /
• 2008

Generally, in analysis of reliability of Design and Development Phase, reliability of electrical components is analyzed based on standards such as MIL-HDBK-217F, Bellcore Issue 4,5,6 by analyzing stress of architectural side (Power, Voltage, Current and quality level of components) of weapon system and stress of operational side (operational environment, operational temperature, Operational Profile). But the reliability of mechanical components is analyzed based on the data book of failure history of mechanical parts called NPRD-95(Nonelectronic Parts Reliability Data-95) without any analysis of above stress. However, even if it's the same mechanical parts, it might have different failure rate(fatigue, wear, corrosion) during operation depending on how weary(stress : pressure, vibration, temperature during operation) the parts are. Therefore, analyzing reliability using just data book can cause big difference in reliability instead of analyzing based upon stressfulness that parts might have, operational concept, and other various factors. Thus, This paper will guide the way of predicting reliability by organizing ways of predicting reliability for system organization and adopt ing NSWC-98/LE1(Naval Surface Warfare Center-98/LE1) for mechanical components.