• 한국자동차공학회논문집
• /
• 제14권2호
• /
• pp.114-120
• /
• 2006

The basic effects of hydrogen addition for engine performance and emission were investigated in single cylinder research engine. Seven commercial injectors were tested to choose a suitable injector for hydrogen injection prior to its engine implementation. The hydrogen fuel leakage and flow rate were evaluated for each injector and KN3-1(Keihin, CO.) showed the best performance for hydrogen fuel. At the higher excess air ratio(${\lambda}=1.7$, 2.0), the better combustion stability was found with hydrogen addition even though its effect was small at lower excess air ratio (${\lambda}=1.0$, 1.3). Stable operation of the engine was even guaranteed at ${\lambda}=2.0$, if the amount of hydrogen gas was near 15% of total energy. In the lean region, ${\lambda}>1.3$, thermal efficiency was improved slightly while it was not clearly observed at ${\lambda}=1.0$, 1.3. It is considered that, in some cases, high temperature environment due to hydrogen combustion caused further heat loss to surroundings. Except for ${\lambda}=1.0$, with larger amount of hydrogen addition, CO was reduced drastically but it was emitted more at the leaner region. Nitric oxides(NOx) was increased a little more with hydrogen addition at ${\lambda}=1.0$, 1.3. However, at ${\lambda}>1.3$ its relative amount of emission was low. In addition, the amount of NOx was continuously decreased with hydrogen addition, but, at ${\lambda}=2.0$ the amount of NOx was lowered to 1/100 of that of ${\lambda}=1.0$. THC emission was significantly increased as air/fuel ratio was raised to leaner region due to misfire and partial burn.

• Journal of Microbiology and Biotechnology
• /
• 제14권4호
• /
• pp.829-835
• /
• 2004

A fibrinolytic enzyme has been found in several bacteria isolated from fermented food. This study was carried out to investigate the purification and characteristics of the fibrinolytic enzyme produced by Bacillus subtilis KCK-7 originated from Chungkookjang. The fibrinolytic enzyme was purified to homogeneity from the culture supernatant using ammonium sulfate fractionation and chromatographies on DEAE-cellulose and on Sephadex G-100. The final specific activity of the purified enzyme increased 11.0-fold, and the protein amount in the purified enzyme was about 16% of that in the culture supernatant. The molecular weight of the purified enzyme was estimated to be about 45,000 by SDS-PAGE. The optimum pH and temperature for the enzyme activity were pH 7.0 and $60^{\circ}C$, respectively. The enzyme activity was relatively stable up to $60^{\circ}C$ over the pH range of 7.0-10.0. The fibrinolytic enzyme activity increased by $Ca^{2+}$ and $Cu^{2+}$, whereas it was inhibited by $Hg^{2+}$ and $Ba^{2+}$. In addition, it was severely inhibited by PMSF and DFT. It is suggested that the purified enzyme was a serine protease for the fibrinolysis. The purified enzyme could completely hydrolyze fibrin in vitro within 8 h. Hence, it is suggested that the purified enzyme can be put into practice as an effective thrombolytic agent.

• 한국미생물·생명공학회지
• /
• 제17권3호
• /
• pp.213-218
• /
• 1989

Cloning을 위한 host와 vector의 이용 가능성을 타진하기 위해 호알칼리성 Bacillus속 K-17을 host로, pUB110과 pBD64를 vector로 사용하여 Bacillus속 K-17의 protoplast 형질전환조건을 검토하였다. 원형질체의 형성은 200$\mu\textrm{g}$/$m\ell$의 Iysozyme 을 처리하였으며, 원형질체 형성의 최적 온도, PH및 배양시간은 각각 4$0^{\circ}C$, 7.0 및 4시간으로 나타났다. 원형질체는 DM3 재생배지에서 재생시켰으며 0.8% agar, 0.5M sodium succinate 농도에서 가장재생이 좋았다. 형질전환시 PEG의 농도는 40%(w/v) PEG 6,000 30%(v/v)가 최적으로 나타났다. 형질전환체의 특성을 조사한 결과, plasmid 안정성은 pUB110이 pBD64보다 더 안정하였으며, 최대 효소활성은 비슷하였지만 효소 분비시간은 pUB110 은 2.5일, pBD64의 경우는 3일로 Bacillus속 K-17의 2일에 비해 약간 지연되었다.

• 한국식품과학회지
• /
• 제25권5호
• /
• pp.576-581
• /
• 1993

김치 조직의 연화에 관여하는 효소인 polygalacturonase(PG)를 배추에서 추출하여 황산암모늄 분획, 이온교환크로마토그래피 및 FPLC를 이용하여 D-PG, C-1, C-2 PG 세 분획으로 분리 정제하여 특성을 조사하였다. 분리된 세 분획의 활성 최적 온도는 $65^{\circ}C$, 최적 pH가 5.2였으며 pH$4.5{\sim}8.0$ 범위에서 안정하였다. NaCl에 의한 영향은 0.3M NaCl에서 최대의 활성을 보였으나 0.6M 이상에서는 저해를 받았으며 $CaCl_2$의 경우 $0{\sim}0.5mM$ 농도에서는 활성이 크게 영향을 받지 않았으나 0.8mM에서는 저해를 받았다. 열불활성화 특성은 isozyme간에 큰 차이가 없었으며 1차 반응을 따랐다. 이 효소 isozyme의 z값은 $8.4{\sim}9.3^{\circ}C,\;80^{\circ}C$에세 D값은 $102{\sim}126$초였다. 이 호소의 불활성화 값을 이용하여 retort pouch 김치 살균공정에 적용하고 역가의 잔존 가능성에 대하여 고찰하였다.

• 멤브레인
• /
• 제18권3호
• /
• pp.250-255
• /
• 2008

열적, 기계적, 화학적 안정성이 우수한 제올라이트 분리막의 물/에탄올 선택도를 이온교환 실험을 통해 더욱 효과적으로 높이고자 하였다. KA형 제올라이트 분리막을 직접 합성하는 것은 용이하지 않으므로 NaA형 제올라이트 분리막을 합성한 후 이를 다시 이온교환 하여 KA형 제올라이트 분리막을 제조하였다. 공급되는 에탄올의 농도 변화 및 투과 증발실험 온도의 변화가 투과플럭스와 물 선택도에 미치는 영향을 고찰하였다. 이온교환 실험 후 전체 투과플럭스는 감소하였고 물 선택도는 증가함을 관찰할 수 있었다.

• 한국항공우주학회지
• /
• 제39권9호
• /
• pp.858-865
• /
• 2011

본 논문은 연료전지 항공기를 위한 고체상태 $NaBH_4$의 수소발생 및 연료전지 구동 특성에 대해서 기술하고 있다. 수소 저장밀도를 높이기 위해서 고체상태 $NaBH_4$와 염산을 반응시켜 수소를 발생시키는 방법을 사용하였다. 다양한 반응 조건에서 고체상태 $NaBH_4$의 수소 발생률을 측정하였다. 고체 $NaBH_4$의 수소 발생률은 염산의 주입속도와 농도에 영향을 받지만, 환경온도에 영향을 받지 않는 것을 확인하였다. 연료전지를 고체 $NaBH_4$ 수소 발생기에 연결하였다. 전기적 부하가 서서히 혹은 급격히 증가하여도 안정적인 출력을 유지하는 것을 확인하였다.

• Journal of Pharmaceutical Investigation
• /
• 제40권2호
• /
• pp.85-90
• /
• 2010

Docetaxel-loaded liposomes were prepared by emulsion-solvent evaporation method, then coated with chitosan at room temperature and lyophilized. This system was designed in order to improve solubility and stability of docetaxel in the GI tract for oral drug delivery. The solubilizing effect of some frequently used solubilizers and/or liposome was determined. Among the results docetaxel-loaded liposomes prepared with 0.5% TPGS as a solubilizer showed 100-fold higher solubility than docetaxel. In a stability test, mean particle size of different liposome formulations was measured by a particle size analyzer in simulated gastric fluid (SGF) and in simulated intestinal fluid (SIF). The particle size of uncoated liposomes was significantly increased compared with that of chitosan-coated liposomes in SGF, however, there was no significant difference between coated and uncoated liposome in SIF. It is evident that chitosan-coated liposomes were more stable in GI conditions. The release characteristics of docetaxel-loaded liposomes were also investigated in three buffer solutions (pH 1.2, 4.0, 6.8). Docetaxel release did not occur in pH 1.2 for 4 hrs. However, in pH 4.0 and 6.8 conditions, docetaxel was gradually released over 24 hrs as a sustained release. It seems that aggregation and precipitation of particles by electrostatic interaction might protect docetaxel from being released. In Conclusion, the results from this study show that the chitosan-coated liposomes may be useful in enhancing solubility and GI stability of docetaxel.

• Applied Biological Chemistry
• /
• 제38권2호
• /
• pp.106-110
• /
• 1995

알칼리성 protease를 생산하는 균을 고추장에서 분리하여 Alteromonas sp. CN301로 동정하고 그 알칼리성 protease를 생산하여 정제효소의 성질을 조사한 결과, 최적 pH 12.0, 최적 온도 $35^{\circ}C$이었으며 pH 안정성은 $pH\;6.0{\sim}13.0$ 범위에서 80% 이상의 잔존효소 활성을 나타냈고 $50^{\circ}C$에서 1시간 처리로 64%의 활성을 보였다. SDS-PAGE에 의한 분자량은 31,000 dalton이었고 $Hg^{2+}$를 제외한 다른 금속이온에 대해서는 저해를 받지 않았다. 계면활성제인 Triton X-100, Tween 20과 80은 이 효소의 활성을 상승시키는 효과를 보였으며 EDTA와 PMSF에 의하여 효소활성이 저해되므로 효소분자 중에 금속이온을 가지는 serine protease로 생각되었다.

• 한국식품조리과학회지
• /
• 제24권4호
• /
• pp.480-486
• /
• 2008

구기자의 수용성 추출물을 첨가한 시럽에 집청한 유과(YU-G)를 제조하여 PE 필름 봉지에 넣고 함기 포장한 후 상온에서 12주간 저장하면서 유과의 품질 특성을 검토하였다. 저장하는 동안 YU-G는 구기자 추출물을 첨가하지 않은 시럽에 집청한 유과(YU-NG)에 비해 수분함량은 높았고 기계적 경도는 낮았다. 저장시 YU-NG와 YU-G의 L값은 감소하고 a값과 b값은 증가하였다. 상온 저장 시 유과의 과산화물가와 산가가 증가하였으며, YU-G는 YUNG에 비해 과산화물가와 산가가 낮았다. 12주 저장 후 YU-G 의 과산화물가는 식품공전 기준치인 40 meq/kg 보다 낮았고 산가는 식품공전기준치인 4 KOH mg/g 보다 낮은 값을 보였으나, YU-NG의 과산화물가는 6주 저장 후, 산가는 10주 저장 후 식품공전 기준치를 초과하였다. 유과의 관능검사 결과, YU-G는 YU-NG보다 저장하는 동안 전반적인 선호도가 높았다.

• Transactions on Electrical and Electronic Materials
• /
• 제8권2호
• /
• pp.67-72
• /
• 2007

High Pressure Micro Jet (HPMJ) pad conditioning system was investigated as an alternative to diamond disc conditioning in copper CMP. A series of comparative 50-wafer marathon runs were conducted at constant wafer pressure and sliding velocity using Rohm & Haas IC1000 and Asahi-Kasei EMD Corporation (UNIPAD) concentrically grooved pads under ex-situ diamond conditioning or HPMJ conditioning. SEM images indicated that fibrous surface was restored using UNIPAD pads under both diamond and HPMJ conditioning. With IC1000 pads, asperities on the surface were significantly collapsed. This was believed to be due to differences in pad wear rates for the two conditioning methods. COF and removal rate were stable from wafer to wafer using both diamond and HPMJ conditioning when UNIPAD pads were used. Also, HPMJ conditioning showed higher COF and removal rate when compared to diamond conditioning for UNIPAD. On the other hand, COF and removal rates for IC1000 pads decreased significantly under HPMJ conditioning. Regardless of pad conditioning method adopted and the type of pad used, linear correlation was observed between temperature and COF, and removal rate and COF.