• 한국재료학회지
• /
• 제25권8호
• /
• pp.398-402
• /
• 2015

Fundamental studies of microstructural changes and high temperature deformation of titanium aluminide (TiAl) were conducted from the view point of the effect of Al content in order to develop the manufacturing process of TiAl. Microstructures in an as cast state consisted mainly of lamellar structure irrespective of Al content. By homogenization at 1473 K, the microstructures of Ti-49Al and Ti-51Al were transformed into an equiaxial structure which was composed of ${\gamma}$-TiAl, while the lamellar structure that was observed in Ti-46Al and Ti-47Al was much more stable. We found that the reduction of Al content suppressed the formation of equiaxial grains and resulted in a microstructure of only a lamellar structure. On Ti-49Al and Ti-51Al, dynamic recrystallization occurred during high temperature deformation, and the microstructure was transformed into a fine equiaxial one, while the microstructures of Ti-46Al and Ti-47Al contained few recrystallized grains and consisted mainly of a deformed lamellar structure. We observed that on the low-Al alloys the lamellar structure under hard mode deformation conditions deformed as kink observed B2-NiAl. High temperature deformation characteristics of TiAl were strongly affected by Al content. An increase of Al content resulted in a decrease of peak stress and activation energy for plastic deformation and an increase of the recrystallization ratio in TiAl.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2009년도 춘계 학술논문 발표대회 학계
• /
• pp.119-122
• /
• 2009

As architectures have recently become high-risers and mega-structured, stable high strength products have been ensured. Accordingly, use of precast concrete accouplement has been increased in order to facilitate air compression and rationalize construction. Since not only external heating but a1so internal temperature rise caused by the accumulation of cement hydration heat in manufacturing process, precast concrete members with large cross-section used for high-rise mega-structure's columns and beams may exhibit different temperature history compared to the precast concrete members for wall and sub-floor with relatively small cross-sections. Therefore, this study aims to elucidate the characteristics of temperature history of mass concrete members cast with high-strength concrete fur precast concrete application. In this study, large cross-sectional precast concrete mock-up, unit cement quantity, and temperature histories in manufacturing precast concrete member under different curing condition were inclusively investigated.

• 한국전기전자재료학회논문지
• /
• 제20권11호
• /
• pp.948-952
• /
• 2007

In this study, a low temperature sintering multilayer piezoelectric transformer for a DC-DC converter was manufactured using $(Pb,Ca,Sr,)(Ti,Mn,Sb)O_3$ ceramics. Its electrical properties were investigated according to the variation in frequency and load resistance. The voltage step-up ratio of the multilayer piezoelectric transformer showed a maximum value at a resonant frequency of input part and increased with an increase of load resistance. The efficiency of the multilayer piezoelectric transformer showed the highest value at a load resistance of 17 $\Omega$. The output power was increased with increasing input voltage. Temperature increase of the multilayer piezoelectric transformer was increased with the increase of output power. At the load resistance of 17 $\Omega$, the multilayer piezoelectric transformer showed the temperature rises of about $20^{\circ}C$ at the output power of 18 W, and stable driving characteristics.

• 상하수도학회지
• /
• 제11권1호
• /
• pp.33-41
• /
• 1997

An attempt was made to enhance anaerobic treatment efficiency by adopting the anaerobic sequencing batch reactor(ASBR) process at a thermophilic temperature. Operational characteristics of the ASBR process were studied using laboratory scale reactors and concentrated organic wastewater composed of soluble starch and essential nutrients. Effects of fill to react ratio (F/R) were examined in the Phase I experiment, where the equivalent hydraulic retention time(HRT) was maintained at 5 days with the influent COD of 10g/L. A continuous stirred tank reactor(CSTR) was operated in parallel as a reference. Treatment efficiency was higher for the ASBRs because of continuous accumulation of volatile suspended solids(VSS) compared to the CSTR. However, the rate of gas production and organic removal per unit VSS in the ASBRs was much lower than the CSTR. This was caused by reduced methane fermentation due to accumulation of volatile acids(VA), especially for the case of low F/R, during the fill period. When the F/R was high, maximum VA was low and the VA decreased in short period. Consequently, more stable operation was possible with higher F/R. Effects of hydraulic loading rate on the efficiency was studied in the Phase II experiment, where the organic loading rate was elevated to 3333mg/L-d with the F/R of 0.12. Reduction of organic removal along with rapid increase of VA was observed and the stability of reaction was seriously impaired, when the influent COD was doubled. However, operation of the ASBR was quite stable, when the hydraulic loading rate was doubled and a cycle time was adjusted to 12 hour. It is essential to avoid rapid accumulation of VA during the fill period in order to maintain operational stability of the ASBR.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.821-825
• /
• 2002

ZnO thick films by Sol-Gel processing were investigated electrics, optics and the sensing characteristics of CO gas. Using the znic acetate dihydrate and acetylaceton (AcAc) as a chelating agent, stable ZnO sol was synthesized. ZnO phase was crystallized through the heat-treatment at $70^{\circ}C$ for 4hrs and influenced the sensing characteristics of the electrics and CO gas by uniform particle distributions not related particle size. The samples on the alumina substrate by thick films were investigated the properties of electrics and the effect of sensing. The sensitivity was so excellent in the sample of the heat-treatment at $600^{\circ}C$ for 12hrs and good in the heat-treatment for 1hrs generally. Crystallization and volatilization of organic materials according to the change of heating treatment temperature of thick films were analyzed by TG-DTA, XRD and mirostructure of thick films were observed by SEM.

• 한국연소학회지
• /
• 제3권2호
• /
• pp.29-40
• /
• 1998

Flame structures and NOx formation characteristics in the flame lets of coflow and counterflow diffusion flame are numerically studied. Calculations were carried out twice with the $C_2-Full$ and $C_2-Thermal$ Mechanism for each flame. Mixture fractions and scalar dissipation rates are used as the parameters to compare the flame let structures and NOx formation characteristics quantitatively. It was found that there is a similarity in flame temperature and stable species profiles except radical profiles between two flamelets. And there are some differences in NOx concentration and production rates. These results imply that the flow effects must be considered in calculations for NOx formation of turbulent flames using Laminar Flamelet Model.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2002년도 제25회 KOSCI SYMPOSIUM 논문집
• /
• pp.71-79
• /
• 2002

The characteristics of the catalytically supported combustion with Pd and Pd/Pt based catalyst using the bench-scaled high pressure combustor have been investigated up to 5atm. This study aimed to investigate combustion characteristics of the stable flame attached to the exit of catalyst bed and NOx emissions with respect to the position of axial and radial direction in the combustor. NOx emissions were increased along the axial distance after the catalyst bed exit and radially decreased from the center to the wall of the combustor. At the higher pressure, the NOx emission decreased slightly due to the lower flame temperature in the combustor at the high pressure.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.145-148
• /
• 2008

Fuel flexibility of CFBC boiler was examined. Combustion characteristics of low grade coal, coal sludge, coal RDF mixture and RDF were compared. The operation result of a commercial 130TPH CFBC co-generation boiler burning a low grade Chinese coal were analysed. Burning characteristics of coal/RDF mixture and coal and industrial sludge mixture were studied in a 0.1MWth scale CFBC test rig. Also RDF fuel were tested in a 8TPH CFBC test facility. Though fuel characteristics were different, the combustion modes were all very stable. The temperature were maintained in between $800-950^{\circ}C$.

• 대한전자공학회논문지
• /
• 제27권1호
• /
• pp.81-90
• /
• 1990

In this study, ion beam deposited tungsten thin film for gate material of GaAs SAGFET(Self Aligned Gate FET) was annealed from 800\ulcorner to 900\ulcorner using RTA and detailed investigations of structural and electrical characteristics of this film were carried out using four-point probe, XRD, SEM, AES and current-voltage measurement. Investigated results showed phase of as deposited tungsten film was fine grain \ulcornerphase and phase tdransformation of this film into \ulcornerphase occured at annealing condition of 900\ulcorner, 6sec. But regardless of phase transformation, electrical characteristics of tungsten film were very stable to 900\ulcorner and in case of 900\ulcorner, 4sec annealing condition Schottky barrier height obtained from 10 diodes measurements was 0.66 + 0.003 eV.

• 한국세라믹학회지
• /
• 제26권3호
• /
• pp.381-389
• /
• 1989

Effects of annealing temperature, time, and atmospehre on the flow characteristics of Atmospheric Pressure Chemical Vapor Deposition-borophosphosilicate glass were investigated. Stable step coverage can be obtained by annealing the BPSG film at 90$0^{\circ}C$ for 30 minutes in N2 atmosphere, but further heat treatment isnot effective. Flow characteristics of the BPSG film was better in steam atmosphere than in N2 atmosphere, and the factors which cause it were analyzed. The concentration of boron in the BPSG film was measured pretty accurately by FTIR spectrum. Boron content in the BPSG film was reduced by annealing treatment. The decrement of boron was greater in steam atmosphere than in the N2 atmosphere. Also it was found from the FTIR spectroscopic analysis that PH3 inhibited the oxidation of B2H6.