• 천문학회보
• /
• 제42권2호
• /
• pp.61.3-61.3
• /
• 2017

We have studied the high-resolution $H{\alpha}$ and Ca II $8542{\AA}$ line profiles of Ellerman Bombs (EBs) obtained with the Fast Imaging Solar Spectrograph (FISS) installed on the 1.6m Goode Solar Telescope (GST) in Big Bear Solar Observatory (BBSO). The FISS spectra of EBs are compared with synthetic profiles computed using RH non-LTE radiative transfer code and a set of 1D atmospheric models with local transient heating, the latter of which is modeled by varying local temperature enhancement in magnitude and height. We could reproduce each of the observed $H{\alpha}$ and Ca II line profiles separately with different atmospheric models, but not with a single atmospheric model. To fit the observed $H{\alpha}$ lines we often need much higher temperature enhancements than those needed for fitting Ca II lines. Possible causes for this temperature mismatch are briefly discussed.

• 한국결정성장학회지
• /
• 제15권4호
• /
• pp.129-134
• /
• 2005

초크랄스키 단결정장치내 실리콘 유동의 자기장효과에 대한 수치해석을 하였다. 8" 단결정 성장과정에서 난류 모형을 사용하여 수송현상을 계산하였다. 도가니 회전수가 작으면 자연대류가 지배적이었다. 도가니 회전수가 증가할수록 강제대류가 증가되며 온도 분포는 더 넓어진다. cusp 자기장을 인가하면 도가니근처의 유동이 크게 감소하며 온도분포는 전도의 경우와 비슷해진다.

• 한국군사과학기술학회지
• /
• 제20권5호
• /
• pp.654-664
• /
• 2017

The temperature profiles upon high speed impact of reactive structural materials were analyzed. A two color pyrometer, which included high-speed camera, spectral splitter, and band pass filters, was utilized to measure transient temperature profiles during and after reactive metal samples impacted into steel plate with velocities of 1600~1700 m/s. The spatial temperature distribution was analyzed from the ratio of spectral radiances at two different wavelength in infrared zone, i.e. 700 and 900 nm. The measured temperatures were calibrated with black body source. Two different types of metal samples, namely aluminum and nickel, were employed to understand reaction behavior upon the impact of samples in ambient condition. According to our experiments, the Ni sample appeared to barely react with ambient air producing an instant small fireball, while Al sample reacts violently with air generating a relatively prolong fireball.

• 대한기계학회논문집B
• /
• 제26권11호
• /
• pp.1481-1487
• /
• 2002

The thin SiC filament technique has been employed to identify the possibility of measuring flame temperature, and especially unstable near-extinction flame temperature in an oxidizer deficient ambience, by comparing the relative visible (non-IR) luminosities of SiC filaments with thermocouple measured temperature in co-flowing, laminar propane/air diffusion flames. The results show good agreement between the digitized relative visible luminosity profiles of the SiC filaments and temperature profiles measured using a thermocouple at temperatures above $700^{\circ}C$, although, a non-linear calibration is probably required far the whole temperature range. The highest radial peak temperature exists near to the nozzle exit. and the centerline temperatures were virtually unchanged with increasing flame height in an oxidizer deficient near-extinction flame.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1997년도 Proceedings of the 12th KACG Technical Meeting and the 4th Korea-Japan EMGS (Electronic Materials Growth Symposium)
• /
• pp.197-201
• /
• 1997

The momentum, heat and mass trasfer phenomena in the silicon melt of the Czochralki crystal growth system are calculated using a three dimensional numerical simulation thechnique. Even though axisymmetrical boundary conditions are imposed to all calculations in a 3cm diameter crucible, several types of non-axisymmetric profiles of velocities, temperature and oxygen concentration appeared in the melt. Because of the non-axisymmetric profiles of velocities, temperature and oxygen concentration appeared in the melt. Because of the non-axisymmetric profiles and rotations of fluid induced by the crucible rotation, temperatures and oxygen concentrations in the silicon melt fluctuate. The rotating velocity of the profile is calculated from the phase shift of the data of temperature or oxygen at two different points which have same radius from center but 90 degree angular difference. From this calculation, it is found that the rotating veolocity of the oxygen and temperature is different from the crucible rotation rates. Therefore the frequencies of the oscillating temperature and oxygen concentrations are not same to the frequencies of the crucible rotations. Futhermore, the components of the frequencies of the temperature and oxygen concentration at the same point are not same. The fluctuation behaviors of the temperature or oxygen themselves are also different when the points are different. The calculation show that the temperature and the oxygen concentration near the interface also fluctuate. The results suggest that the striation pattern found in the grown silicon single crystals may ben generated by the oxygen concentration and the temperature oscillations of the melt occurred near the interface.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2006년도 Proceedings of ISRS 2006 PORSEC Volume I
• /
• pp.250-252
• /
• 2006

The land surface temperature (LST) can be defined as a weighted average temperature of components which constitute a pixel. The coefficients of split-window algorithm for MTSAT-1R were obtained by means of a statistical regression analysis from radiative transfer simulations using MODTRAN 4.0 for a wide range of atmospheric, satellite viewing angle (SVA) and lapse rate conditions. 6 types of atmospheric profile data imbedded in the MODTRAN 4 are used for the radiative transfer simulations. The RMSE is clearly larger on warm and humid profiles than cold and dry profiles, especially when the satellite viewing angle and lapse rate are large. The derivation of LST equations according to the atmospheric profiles clearly decreased the RMSE without regard to the SVA and lapse rate. The bias and RMSE are decreased as the more controls factors included. This preliminary result indicates that the characteristics of atmosphere, SVA and lapse rate should be included in the LST equation.

• 대한원격탐사학회지
• /
• 제22권5호
• /
• pp.385-388
• /
• 2006

The land surface temperature (LST) can be defined as a weighted average temperature of components which constitute a pixel. The coefficients of split-window algorithm for MTSAT-1R were obtained by means of a statistical regression analysis from radiative transfer simulations using MODTRAN 4.0 for a wide range of atmospheric, satellite viewing angle (SVA) and lapse rate conditions. 6 types of atmospheric profile data imbedded in the MODTRAN 4 are used for the radiative transfer simulations. The RMSE is clearly larger on warm and humid profiles than cold and dry profiles, especially when the satellite viewing angle and lapse rate are large. The derivation of LST equations according to the atmospheric profiles clearly decreased the RMSE without regard to the SVA and lapse rate. The bias and RMSE are decreased as the more controls factors included. This preliminary result indicates that the characteristics of atmosphere, SVA and lapse rate should be included in the LST equation.

• 대한기계학회논문집
• /
• 제1권3호
• /
• pp.146-155
• /
• 1977

The free convection in a vertical tube open at both ends and heated at the heated at the wall is studied by analytical approach and checked by experiment. The flow is assumed to be both stable and laminar. The incompressible boundary layer equations fot the system were solved by a finite difference method for conditions of constant wall temperature and conctant wall heat flux. Temperature profiles of the flow in the tube were measured by thermocouples and are compared with the calculated profiles. Agreement of the analytical and experimental results was good.

• 한국음향학회지
• /
• 제6권1호
• /
• pp.29-38
• /
• 1987

Hyperthermia의 임상 응용에서 측정할 수 있는 온도치는 수 점의 온도치로 제한되는데 효과적인 치료를 위해서는 그 외의 점에서의 정확한 온도분포를 알아야 할 필요가 있다. 이를 위하여, 본 논문에서는 생체 열전달 방정식을 1차원 2경계치 문제로 단순화시켜 계산시간을 줄였으며 Galerkin법을 이용하여 그 근사해률 구하였다. 그 결과를 동심환 초음파 변환기에 적용하여 축방향의 온도분포를 계산하였으며 측정된 수 점의 온도로부터 축방향의 온도분포를 추정할 수 있는 알고리즘을 제시하였다.

• 한국주조공학회지
• /
• 제20권2호
• /
• pp.80-88
• /
• 2000

Continuous casting equipment was designed to cast the metallic uranium rods, and a thermal analysis was carried out to calculate the temperature and solidification profiles. Fluid flow and heat transfer analysis model including the effects of phase change was used to simulate the continuous casting process by finite volume method. In the design of continuous casting equipment, the casting speed, pouring temperature and cooling conditions should be considered as significant factors. In this study, the effects of casting speed, pouring temperature, and air gap between the uranium and mold were investigate. The results represented that the temperature and solidification profiles of continuous casting equipment varied with the casting speed, pouring temperature, and air gap.