• 마이크로전자및패키징학회지
• /
• 제23권3호
• /
• pp.43-49
• /
• 2016

박형 package-on-package에 대해 T/H (temperature/humidity) 시험, TC (temperature cycling) 시험과 HTS(high temperature storage) 시험을 사용하여 신뢰성을 분석하였다. T/H 시험은 $85^{\circ}C/85%$의 조건으로 500시간, TC 시험은 $-40{\sim}100^{\circ}C$의 조건으로 1000회, HTS 시험은 $155^{\circ}C$의 조건으로 1,000시간 범위에서 평가하였다. 폴리이미드 써멀테이프를 사용하여 제작한 24개의 package-on-package (PoP) 시편에 대해 신뢰성 시험 전에 측정한 솔더접속 배선의 평균저항은 $0.56{\pm}0.05{\Omega}$이었으며, 24개 시편에서 모두 유사한 값이 측정되었다. 500시간까지의 T/H 시험, 1000회의 TC 시험 및 1,000시간까지의 HTS 시험후에도 솔더 접속부의 오픈 불량은 발생하지 않았다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2002년도 추계학술발표강연 및 논문개요집
• /
• pp.87-87
• /
• 2002

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 1999년도 Pre-symposium of the 10th ISWPC Recent Advances in Paper Science and Technology
• /
• pp.361-365
• /
• 1999

This study examined the effects of multiple recycling on deinkability and properties of recycled paper from laser computer printout (LCPO). First, alkaline paper with a 20% printed area was disintegrated by TAPPI standard disintegrator at room temperature. After dewatering, the pulp was flotated and dried in oven at80$^{\circ}C$ for 24 hrs. A sequence of wetting, disintegrating, flotating and drying was one recycling cycle and this cyclic treatment was repeated from zero to five times. The recycled handsheet dropped to 90% of the original brightness after five cycles, and lost the most brightness after five cycles, and lost the most brightness in the first two cycles. However, it had a gain of 10% in opacity after five cycles as the same as the case of nonprinting. And, in this study, the method for determining residual ink(toner) content in recycled handsheets ere established by means of SEM-EDX and Py-GC. The change of residual ink percentage on recycled paper showed the effect of recycling numbers on deinkability of waste paper. A slight decrease in deinkability was noted for the recycled handsheets, which may be due to the change of fiber surface free energy connected with fiber swelling.

• 한국재료학회지
• /
• 제19권8호
• /
• pp.432-436
• /
• 2009

A Cu-Fe-P copper alloy was processed by accumulative roll-bonding (ARB) for ultra grain refinement and high strengthening. Two 1mm thick copper sheets, 30 mm wide and 300 mm long, were first degreased and wire-brushed for sound bonding. The sheets were then stacked on top of each other and roll-bonded by about 50% reduction rolling without lubrication at ambient temperature. The bonded sheet was then cut into two pieces of the same dimensions and the same procedure was repeated for the sheets up to eight cycles. Microstructural evolution of the copper alloy with the number of the ARB cycles was investigated by optical microscopy (OM), transmission electron microscopy(TEM), and electron back scatter diffraction(EBSD). The grain size decreased gradually with the number of ARB cycles, and was reduced to 290 nm after eight cycles. The boundaries above 60% of ultrafine grains formed exhibited high angle boundaries above 15 degrees. In addition, the average misorientation angle of ultrafine grains was 30 degrees.

• 한국재료학회지
• /
• 제25권10호
• /
• pp.571-576
• /
• 2015

The effects of coating thickness on the delamination and fracture behavior of thermal barrier coating (TBC) systems were investigated with cyclic flame thermal fatigue (FTF) and thermal shock (TS) tests. The top and bond coats of the TBCs were prepared by electron beam-physical vapor deposition and low pressure plasma spray methods, respectively, with a thickness ratio of 2:1 in the top and bond coats. The thicknesses of the top coat were 200 and $500{\mu}m$, and those of the bond coat were 100 and $250{\mu}m$. FTF tests were performed until 1140 cycles at a surface temperature of $1100^{\circ}C$ for a dwell time of 5 min. TS tests were also done until more than 50 % delamination or 1140 cycles with a dwell time of 60 min. After the FTF for 1140 cycles, the interface microstructures of each TBC exhibited a sound condition without cracking or delamination. In the TS, the TBCs of 200 and $500{\mu}m$ were fully delaminated (> 50 %) within 171 and 440 cycles, respectively. These results enabled us to control the thickness of TBC systems and to propose an efficient coating in protecting the substrate in cyclic thermal exposure environments.

• 대한금속재료학회지
• /
• 제49권12호
• /
• pp.945-949
• /
• 2011

The cycling characteristics of $MgH_2$ made by hydriding chemical vapor deposition method have been investigated. The particle size of $MgH_2$ made by HCVD was about $1{\mu}m$. The cycling experiment was performed by measuring hydrogen quantity absorbed at 673 K and under 35 atm of hydrogen pressure for 30 min. Up to 3 cycles the hydrogen storage capacity increased, but from 4 to 6 cycles the hydrogen storage capacity decreased rapidly. During this cycling test the particle size increased gradually from $1{\mu}m$ to $6{\mu}m$. This increase was due to sintering by the high reaction temperature and the heat of reaction during hydrogen absorption. From 7 to 30 cycles, the hydrogen storage capacity was maintained at 5.8 wt%. Even after 30 cycles, the plateau pressure was constant.

• 한국재료학회지
• /
• 제24권11호
• /
• pp.585-590
• /
• 2014

Microstructural evolution in the thickness direction of an oxygen free copper processed by accumulative rollbonding (ARB) is investigated by electron back scatter diffraction (EBSD) measurement. For the ARB, two copper alloy sheets 1 mm thick, 30 mm wide and 300 mm long are first degreased and wire-brushed for sound bonding. The sheets are then stacked and roll-bonded by about 50% reduction rolling without lubrication at an ambient temperature. The bonded sheet is then cut to the two pieces of the same dimensions and the same procedure was repeated on the sheets up to eight cycles. The specimen after 1 cycle showed inhomogeneous microstructure in the thickness direction so that the grains near the surface were finer than those near the center. This inhomogeneity decreased with an increasing number of ARB cycles, and the grain sizes of the specimens after 3 cycles were almost identical. In addition, the aspect ratio of the grains decreased with an increasing number of ARB cycles due to the subdivision of the grains by shear deformation. The fraction of grains with high angle grain boundaries also increased with continuing process of the ARB so that it was higher than that of the low angle grain boundaries in specimens after 3 cycles. A discontinuous dynamic recrystallization occurred partially in specimens after 5 cycles.

• 전기학회논문지
• /
• 제60권6호
• /
• pp.1163-1168
• /
• 2011

Most transformers use insulating and cooling fluids derived from petroleum crude oil, but mineral oil has some possibility of environmental pollution and fire with explosion. vegetable oil fluids extracted from seed has superior biodegradation and fire-resistant properties including an exceptionally high fire point enhancing fire safety. In this study, it is aimed at the practicality of substituting natural ester dielectric fluid for mineral oil in liquid insulation system of transformers. As a rise in coil winding temperature has a direct influence on transformer life time, it is important to evaluate the temperature rise of coil winding in vegetable oil in comparison with mineral oil. Four transformers for the test are designed with 10KVA, 13.2KV, one phase unit. The temperature are directly measured in insulating oil of these transformers with the two sorts of natural ester and mineral oil dielectric fluid respectively. Experiment for aging carry out two means. First means remained $120^{\circ}C$ that transformer of mineral oil were operated at 185% load. Second means is that insulating oils of two natural ester and mineral oil were aged by thermal cycles repeating from $30^{\circ}C$ to $120^{\circ}C$. For the heating, Transformers were operated at 185% load. For the cooling, cooling system was operated in the chamber. Samples were analyzed at 42, 63, 93, 143, 190, 240 300cycles. Analysis contents are dielectric strength, total acid value. Mineral oils compared results of first means with results of second means. And compared two sort natural esters respectively with mineral oil in second means.

• Membrane and Water Treatment
• /
• 제8권3호
• /
• pp.279-292
• /
• 2017

This study was aimed at ultrafiltration (UF) as a pretreatment before reverse osmosis (RO) within the scheme of hybrid reverse osmosis-multistage flush (RO-MSF) desalination. Seawater at elevated temperature (after MSF heat-exchangers) was used as a feed in this process. The pretreatment system was represented as a set of functionally-linked technological segments such as: UF filtration, backwashing, chemical- enhanced backwashing, cleaning, waste disposal, etc. The process represents the sequences of operating cycles. The cycle, in turn, consists of the following unit operations: filtration, backwashing and chemical-enhanced backwashing (CEB). Quantitative assessment was based on the following indicators: normalized permeability, transmembrane pressure, specific energy and water consumption, specific waste generation. UF pre-treatment is accompanied by the following waste streams: $W1=1.19{\times}10$ power of $-2m^3$ (disposed NaOCl with 0.0044% wt.)/$m^3$ (filtrate); $W2=5.95{\times}10$ power of $-3m^3$ (disposed $H_2SO_4$ with 0.052% wt.)/$m^3$(filtrate); $W3=7.26{\times}10$ power of $-2m^3$ (disposed sea water)/$m^3$ (filtrate). Specific energy consumption is $1.11{\times}10$ power of $-1kWh/m^3$ (filtrate). The indicators evaluated over the cycles with conventional (non-chemical) backwashing were compared with the cycles accompanied by CEB. A positive impact of CEB on performance indicators was demonstrated namely: normalized UF resistance remains unchanged within the regime accompanied by CEB, whereas the lack of CEB results in 30% of its growth. Those quantitative indicators can be incorporated into the target function for solving different optimization problems. They can be used in the software for optimisation of operating regimes or in the synthesis of optimal flow- diagram. The cycle characteristics, process parameters and water quality data are attached.

• 한국지반공학회논문집
• /
• 제29권1호
• /
• pp.81-92
• /
• 2013

본 논문에서는 계절적 환경변화로 인한 동결-융해 반복과정에 노출되는 옹벽의 시간 의존적 거동에 대한 수치 해석 연구 내용을 다루었다. 이를 위해 먼저 동결-융해 반복과정에 노출되는 옹벽에 대한 열-수리-응력 연계해석 기반의 모델링 기법을 정립하였으며 이러한 모델링 기법을 토대로 다양한 온도변화 조건에 대한 매개변수 연구를 수행하였다. 그 결과 다양한 온도변화 특성 중 옹벽의 거동에 미치는 주된 영향인자는 계절적 평균동결온도와 반복회수인 것으로 나타났다. 반면 동결온도의 지속시간에 대한 영향을 검토한 결과 벽체변위 및 수평토압에 큰 영향을 미치지 않는 것으로 검토되었다. 한편, 벽체에 작용하는 수평토압은 동결-융해 작용에 의한 영향을 거의 받지 않는 것으로 검토되어 결국 동결-융해로 인한 벽체 변위 증가 현상은 토압 증가에 그 원인을 찾기 보다는 동결-융해 현상으로 인한 재료적 열화 현상에 그 원인을 찾아야 할 것으로 검토되었다.