• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.80-83
• /
• 2000

The post-annealing treatments on rf magnetron sputtered PZT($Pb_{1.05}(Zr_{0.52},\;Ti_{0.48})O_3$) thin films($4000{\AA}$) have been investigated for a structure of PZT/Pt/Ti/Coming glass(1737). Crystallization properties of PZT films were strongly dependent on RTA(Rapid Thermal Annealing) annealing temperature and time. We were able to obtain a perovskite structure of PZT at $650^{\circ}C$ and 10min. P-E curves of Pd/PZT/Pt capacitor demonstrate typical hysteresis loops. The measured values of $P_r$, $E_c$ were $8.1[{\mu}C/cm^2]$, 95[kV/cm] respectively. Polarization value decrease about 25% after $10^9$ cycles.

• Journal of Ecology and Environment
• /
• 제33권3호
• /
• pp.223-228
• /
• 2010

Soil microbes perform crucial roles in the nutrient cycles of forest ecosystems, by effecting the decomposition of organic matter. Enzyme activities have been used to evaluate decomposition rates, as well as microbial activities. The principal objectives of this study were to determine the activities of different soil enzymes, to compare enzyme activities at different elevations, and to elucidate the most important controlling variables for enzyme activities. We conducted a field survey at three sites in Mt. Jumbong on a monthly basis from May, 2004 to September, 2005. Enzyme activities did not change substantially over different seasons. However, the spatial differences were distinct; the lowest elevation site evidenced the lowest levels of enzyme activity. Soils at the lowest elevation were nutrient-depleted soils, and enzyme activities appeared to be affected by precipitation and temperature. However, enzyme activities in fertile soils at high elevations were associated with nutrients and organic matter. The enzyme activities detected in this study differed significantly at the three elevations, and their controlling variables also evidenced different factors.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.201-206
• /
• 2002

The purpose of this study is to improve the anti-corrosive properties of coated reinforcing bar using polymer cement slurry. Poymer cement slurry are prepared with three types of polymer dispersions and corrosion inhibiting admixture. And tested for corrosion accelerating tests such as immersion in NaCl 10% solution NaCl 10% solution spray, high temperature and pressure steam in condition of 8cycles, carbonation before and after, penetration of NaCl solution. From the test results, it is concluded that the anti-corrosive properties are considerably improved by coating using polymer cement slurry at surface of reinforcing bar. And this trend is marked by adding of corrosion inhibiting admixture. The difference of the anti-corrosive properties is hardly recognized according to types of polymer dispersions. The anti-corrosive properties of coated reinforcing bar using polymer foment slurry are improved to a great extent compared to those of plain reinforcing bar accordiy to increasing content of chloride ion in cement concrete.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1250-1254
• /
• 1992

This paper describes the designed and fabricated thermal imaging system with the SPRITE(Signal PRocessing in The Element) detector, operating in the 3-12 micron band. This system consists of an afocal telescope, a scan unit containing the SPRITE detector, an electronic processor unit and a cooler. The optical scan system utilizing rotating polygon and oscillating mirror, is 2-dimensional serial/parallel scan type using five elements of the detector. And the electronic processor unit performs digital scan conversion to reform the parallel data stream into serial analog data compatable with conventional RS-170 video. The scan field of view is 40 ${\times}$ 26.7 and the MRTD(Minium Resolvable Temperature Difference) is 0.6 K at 7.5 cycles/mm. The acquired thermal image indicates that this system has a satisfactory performance.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.154-159
• /
• 2007

Some shape memory alloys like NiTi show noticeable high damping property in pseudoelastic range. Due to its instinct characteristics, a NiTi alloy is commonly used for passive damping applications, in which the energy may be dissipated by the conversion from mechanical to thermal energy. Previous researches found the NiTi wires own higher damping property than the bars; therefore the wire form is adopted in this study. A loss factor is introduced for measuring the damping property of the NiTi wires. The experimental observation shows the mechanical behaviors of NiTi wires are dependent on temperature, strain rate and strain amplitude. Moreover, it is found the first several decades of loading-unloading cycles can obviously influence the property of NiTi wires under the same working conditions.

• 한국정밀공학회지
• /
• 제19권8호
• /
• pp.71-76
• /
• 2002

In this study low cycle fatigue (LCF) behavior of 12Cr steel at high temperature are described. Secondly, comparisons between predicted lives and experimental lives are made for the several sample life prediction models. Two minute hold period in either tension or compression reduce the number of cycles to failure by about a factor of two. Twenty minute hold periods in compression lead to shorter lives than 2 minute hold periods in compression. Experiments showed that life predictions from classical phenomenological models have limitations. More LCF experiments should be pursued to gain understanding of the physical damage mechanisms and to allow the development of physically-based models which can enhance the accuracy of the predictions of components. From a design point-of-view, life prediction has been judged acceptable for these particular loading conditions but extrapolations to thermo-mechanical fatigue loading, for example, require more sophisticated models including physical damage mechanisms.

• Tribology and Lubricants
• /
• 제21권6호
• /
• pp.263-267
• /
• 2005

The tribological performance of multi-walled carbon nanotubes (MWNT) in mineral oils is investigated at ambient temperature. The frictional forces, wear amounts and cycles to scuffing of the oils with nanotubes and without those were measured using the ball-on-disk tester. It was found that there were little differences in the frictional forces and wear amounts of two oils. However, the scuffing times of oils with nanotubes were much longer than those of oils without nanotubes in sliding tests. The nanotubes were very effective on maintaining the oil gap and protecting the surfaces in boundary lubricated sliding.

• 한국산업융합학회 논문집
• /
• 제3권1호
• /
• pp.69-75
• /
• 2000

Multichip packages are comprised of dissimilar materials which expand at different rates on heating. The differential expansion must be accommodated by the various structural elements of the package. A types of heat exposures occur operation cycles. This study presents a finite element analysis simulation of flip-chip among multichip. The effects of geometries and material properties on the reliability were estimated during the analysis of temperature and thermal stress of flip-chip. From the results, it could be obtained that the more significant parameters to the reliability of flip-chip arc chip power cycle, heat convection and height of solder bump.

• Steel and Composite Structures
• /
• 제19권4호
• /
• pp.953-966
• /
• 2015

Carbonation depth was verified in 40 points of two 57 years old concrete viaducts. Field testing (phenolphthalein spraying) was performed on the structures. Data obtained were statistically analyzed by the Kolmogrov-Smirnov's test, one-way analysis of variance (ANOVA's test), and Fisher's method. The results revealed significant differences between maximum carbonation depths of different elements of the same concrete structure. Significant differences were also found in the carbonation of different concrete structures inserted in the same macroclimate. Microclimatic factors such as temperature and local humidity, sunshine, wind, wetting and drying cycles, among others, may have been responsible by the behavior of carbonation in concrete.

• 한국주조공학회지
• /
• 제18권6호
• /
• pp.578-585
• /
• 1998

A multi-purpose code MAGMA was employed for mold design and process control in producing Al wheel by lowpressure die casting. Three-dimensional solid modeling was followed by mesh generation of casting and molds(top, bottom and side). The simulation of stability of casting cycle time, mold filling simulation with pressure variation from P1 to P2, solidification simulation by solidification time and feeding criteria, and temperature distribution of molds during processes were studied in this research. The thermal stability of molds was attained after 5 cycles when molds were preheated at $400^{\circ}C$. The pressure increase from P1 to P2 for mold filling was evaluated as slightly higher, and 6 seconds were taken for the mold filling. The cycle time was believed to be designed properly judged from the solidification time of casting and open/close time of molds.