• Journal of the Korean Chemical Society
• /
• v.43 no.4
• /
• pp.423-429
• /
• 1999

A spectrofluorimetric method for the determination of Fe(III) in aqueous solution with 4,5-dihydroxy-1,3-benzenedisulfonic acid(Tiron) as a fluorimetric reporter was developed. Tiron, which is very soluble in water,is a good fluorimetric reagent. However, when Tiron was complexed with Fe(III), the fluorescent intensity was decreased proportionally with the concentration of Fe(III) by a quenching effect. The excitation and fluorescene wavelength of Tiron showing the quenching effect by Fe(III) at pH 4.5 were 312 nm and 341 nm, respectively. The highest sensitivities were shown at Tiron concentration of $1.0{\times}10^{-2}M$. To enhance the quenching effect, the Fe(III)-Tiron complex solution was heated to 80$^{\circ}C$ for 90 minutes. As for Fe(III), the most interfering ion was Cu(II). The interference effects could be mostly eliminated by pH adjustment or by adding EDTA. The concentration ranges showing the linear response to Fe(III) was from $5.0{\times}10^{-7}M\;to\;6.0{\times}10^{-5}M$ With this proposed method, the detection limits of Fe(III) was $2.8{\times}10^{-6}M$. Recovery of Fe(lII) in a synthetic sample was almost quantitative. Based on experimental results, it is proposed that the above technique can be applied to the practical determination of Fe(III).

• Journal of the Korean Chemical Society
• /
• v.40 no.4
• /
• pp.243-248
• /
• 1996

New routes have been developed for the practical syntheses of dl-Muscone(1) employing cyclopentadecanone(2) as the starting material. In this experiment, addition of bromine to cyclopentadecanone in dried E. Ether solution with a trace of $AlCl_3$ as the catalyst were produced 2-bromocyclopentadecanone(3). This process was enhanced formation of regioselective enolate anion at $C_2$ position. 2-Bromocyclopentadecanone was put into $Li_2CO_3$-LiBr-DMF solution at 140∼150$^{\circ}C$, were produced trans- and cis-2-cyclopentadecen-1-one(4) mixture. Other by-products were reduced by control of reaction temperature and time. Trans- and cis-2-cyclopentadecen-1-one(4) mixture was directly put into dried E. Ether solvent and induce to react dropwise with $CH_3MgBr-Cu_2Cl_2$ complex, all of them got into 1,4-addition, dl-Muscone (1) was formed as the result. Conculsion, through three steps procedure from cyclopentadecanone(2) to dl-Muscone(1), the pure dl-Muscone was obtained with the high proportion of 85%, and synthetic cost was able to be much lower than any other conventional methods as there were no chemical separating steps.

• Restorative Dentistry and Endodontics
• /
• v.24 no.2
• /
• pp.330-336
• /
• 1999

In biological systems, the mineral that forms hard tissue is of an apatitic nature, and hydroxyapatite($Ca_5OH(PO_4)_3$: HA) is generally considered as the prototype for such a mineral. Thus, the precipitation of HA, having biological implications, has been the subject of several investigations. Crystal growth studies using HA seeds in supersaturated solutions have enhanced our understanding of the process and mechanism involved in seeded crystal growth. From these studies, it has become apparent that the precipitation rate of HA onto the seed crystals depends on the various conditions, especially on the additives. The relation between the supersaturated solution containing fluoride and the process of HA crystal growth enhances the understanding of mechanism of HA crystal growth. Until recently, the studies have been on the crystal growth of enamel minerals and synthetic HA seeds in the supersaturated solution containing 1~2 ppm fluoride. The purpose of the present investigation is to study the effect that fluoride of high concentration has on the crystal growth kinetics of HA. In order to produce the composition found in the secretory enamel fluid, experimental solutions of 1mM Ca, 3mM P, and 100mM Tris as background electrolyte were used. Then this experimental solutions were added to 0, 2, 4, 6, 8, 10 ppm fluoride. The effect of fluoride at high concentrations on the precipitation was examined in a bench-top crystal growth model adopting a miniaturized reaction column. Chemical analysis was employed for characterization of working solutions before and after the experimentation. Remarkable findings were : 1) the amount of crystal growth was gradually accelerated as the fluoride concentration increased until 6 ppm, but decreased in 8 and 10 ppm fluoride; 2) the amount of fluoride ion consumed in crystal formation was constant despite the increase in fluoride concentration.

• Horticultural Science & Technology
• /
• v.16 no.2
• /
• pp.222-225
• /
• 1998

The objective of this study was to observe the effects of potassium-carboxymethyl cellulose (K-CMC), which is a natural polymer derivative, and polyacrylamide (PAM), which is a commercial synthetic polymer, on soil physicochemical properties and yields of the cabbage. To increase water absorbing capacity (WAC), hydrophilic carboxymethyl group was introduced to cellulose chain and it was confirmed by FT-IR. WAC was tested by tea-bag method in distilled water and 3% NaCl solution. PAM is slightly more absorptive than K-CMC in distilled water, but in NaCl solution, K-CMC is more absorptive than PAM. Soil particle sizes above $1_{mm}$ were immediately increased from 9.6 to approximately 16.6% by the application of K-CMC and PAM, respectively. Infiltration rates of soil were approximately twice as great as those of the control when conditioned with the K-CMC and PAM treatment. K content of soil treated with K-CMC was significantly higher than those of PAM and control, but the other components of soil chemical properties were not different. The early growth and vegetative production of cabbage in the K-CMC and PAM treatments were significantly higher than the control. The contents of vitamin C were increased with the treatment of K-CMC. It was proposed that K-CMC treatment influence K component of the soil and vitamin C content of the cabbage, therefore, it improved the yields as well as crop quality.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.5
• /
• pp.191-198
• /
• 2022

Zirconia and titanium alloys, which are mainly used for dental implant materials, have poor osseointegration and osteogenesis abilities due to their bioinertness with low bioactivity on surface. In order to improve their surface bioinertness, surface modification with a bioactive material is an easy and simple method. In this study, akermanite (Ca₂MgSi₂O₇), a silicate-based bioceramic material with excellent bone bonding ability, was synthesized by a solid-state reaction and investigated its bioactivity from the analysis of surface dissolution and precipitation of hydroxyapatite particles in SBF solution. Calcium carbonate (CaCO₃), magnesium carbonate (MgCO₃), and silicon dioxide (SiO₂) were used as starting materials. After homogeneous mixing of starting materials by ball milling and the drying of at oven, uniaxial pressing was performed to form a compacted disk, and then heat-treated at high temperature to induce the solid-state reaction to akermanite. Bioactivity of synthesized akermanite disk was evaluated with the reaction temperature from the immersion test in SBF solution. The higher the reaction temperature, the more pronounced the akermanite phase and the less the surface dissolution at particle surface. It resulted that synthesized akermanite particles had high bioactivity on particle surface, but it depended on reacted temperature and phase composition. Moderate dissolution occurred at particle surfaces and observed the new precipitated hydroxyapatite particles in synthetic akermanite with solid-state reaction at 1100℃.

• Resources Recycling
• /
• v.31 no.5
• /
• pp.34-41
• /
• 2022

Smelting reduction of spent lithium-ion batteries results in metallic alloys, slag, and dust containing Li(I). Precipitation of Li₂CO₃ was performed using the synthetic leachate of the dust. Herein, the effects of the precipitant and addition of non-aqueous solvents on the precipitation of Li(I) were investigated. Na₂CO₃ was a more effective precipitating agent than (NH₄)₂CO₃ owing to the hydrolysis reaction of dissolved ammonium and carbonate. The addition of acetone or ethanol improved the Li(I) precipitation percentage for both the precipitants. When using (NH₄)₂CO₃, the Li(I) precipitation percentage increased at a solution pH of 12. Under the same conditions, the Li(I) precipitation percentage using Na₂CO₃ was much higher than that using (NH₄)₂CO₃.

• Journal of Oral Medicine and Pain
• /
• v.30 no.1
• /
• pp.1-14
• /
• 2005

The maintenance of good oral health in adults is often hindered by oral malodor and periodontal diseases which are known to be commonly caused by some species of Gram-negative anaerobic bacteria, with low sensitivity to common synthetic antibiotics or antibacterial chemical agents. Therefore the development of a nonharmful natural antibacterial oral rinsing remedy against the causative bacteria is thought to be very important. The purpose of this study is to obtain the basic data for development of a nonharmful natural antibacterial oral rinsing remedy using colloidal silver. The author applied colloidal silver solution with concentration of 10, 30, 50, 80 ppm to some strains in species of Prevotella intermedia, Porphyromonas gingivalis, Fusobaterium nucleatum, and evaluated the effects of colloidal silver on the growth of experimental bacterial strains in aspects of minimal inhibitory concentration (MIC), minimal bactericidal concentration (MBC) and growth pattern after incubation for 24, 48, 72 hours. The obtained results were as follows: MIC of colloidal silver solution against experimental strains was 30 ppm in P. intermedia, 10 or 30 ppm in P. gingivalis, and 30, 50, or 80 ppm in F. nucleatum. And MBC of colloidal silver solution against experimental strains was 30 ppm in P. intermedia, 30 or 50 ppm in P. gingivalis, 30 or 80 ppm in F. nucleatum. Therefore it was concluded that colloidal silver exhibited bacteriostatic or/and bacteriocidal effects against some experimental strain. And the inhibition of growth of experimental strains were markedly or considerably exhibited under 30 ppm$\sim$50 ppm of colloidal silver solution for 48 hours$\sim$72 hours in P. intermedia, 10 ppm$\sim$30 ppm for 24 hours$\sim$48 hours in P. gingivalis, 30 ppm for 24 hours in F. nucleatum. These results indicate that the colloidal silver inhibited effectively the growth of some species of Gram-negative anaerobic bacteria by exhibition of bacteriostatic or/and bacteriocidal effects, and can be used as a possible major ingredient of the nonharmful natural antibacterial oral rinsing remedy to oral malodor and periodontal diseases.

• Economic and Environmental Geology
• /
• v.26 no.3
• /
• pp.327-335
• /
• 1993

Phase relations in the system Pd-Sb-Te were investigated at $1000^{\circ}$, $800^{\circ}$, and $600^{\circ}C$, using the sealed-capsule technique; the quenched products were studied by reflected light microscopy, X-ray diffraction, and electron microprobe analysis. At $1000^{\circ}C$, the solid phases Pd, $Pd_{20}Sb_7$, $Pd_8Sb_3$, $Pd_{31}Sb_{12}$, and $Pd_5Sb_2$ are stable with a liquid phase that occupies most of the isothermal diagram. Additional solid phases at $800^{\circ}C$ are $Pd_5Sb_3$, PdSb, $Pd_8Te_3$, $Pd_7Te_3$, and a continuous $Pd_{20}Te_7-Pd_{20}Sb_7$ solid solution becomes stable. At $600^{\circ}$, $PdSb_2$, $Pd_{17}Te_4$, $Pd_9Te_4$, PdTe, $PdTe_2$, $Sb_2Te_3$, and Sb and continuous PdSb-PdTe and $PdTe-PdTe_2$ solid solutions are stable. All the solid phases exhibit solid solution, mainly by substitution between Sb and Te to an extent that varies with temperature of formation. The maximum substitution (at.%) of Te for Sb in the Pd-Sb phases is: 44.3 in $Pd_8Sb_3$, 52.0 in $Pd_{31}Sb_{12}$, 46.2 in $Pd_5Sb_2$ at $800^{\circ}C$; 15.3 in $Pd_5Sb_3$, 68.3 in $PdSb_2$ at $600^{\circ}C$. The maximum substitution (at.%) of Sb for Te in the Pd-Te phases is 34.5 in $Pd_5Sb_3$ at $800^{\circ}C$, and 41.6 in $Pd_7Te_3$, 5.2 in $Pd_{17}T_4$, 12.4 in $Pd_9Te_4$, and 19.1 in $PdTe_2$ at $600^{\circ}C$. Physical properties and X-ray data of the synthetic $Pd_9Te_4$, PdTe, $PdTe_2$, $Pd_8Sb_3$, PdSb, and $Sb_2Te_3$ correspond very well with those of telluropalladinite, kotulskite, merenskyite, mertieite II, sudburyite, and tellurantimony, respectively. Because X-ray powder diffraction data consistently reveal a 310 peak ($2.035{\AA}$), the $PdSb_2$ phase is most probably of cubic structure with space group $P2_13$. The X-ray powder pattern of a phase with PdSbTe composition, synthesized at $600^{\circ}C$, compares well with that of testibipalladite. Therefore, testibiopalladite may be a member of the $PdSb_2-Pd(Sb_{0.32}Te_{0.68})$ solid solution series which is cubic and $P2_13$ in symmetry. Thus the ideal fonnula for testibiopalladite, presently PdSbTe, must be revised to PdTe(Sb, Te). Borovskite($pd_3SbTe_4$) has not been found in the synthetic system in the temperature range $1000^{\circ}-600^{\circ}C$.

• Korean Journal of Mineralogy and Petrology
• /
• v.35 no.2
• /
• pp.101-109
• /
• 2022

The mobility and transport of radioactive cesium are crucial factors to consider for the safety assessment of high-level radioactive waste disposal sites in granite. The retardation of radionuclides in the fractured crystalline rock is mainly controlled by the hydrochemical condition of groundwater and surface reactions with minerals present in the fractures. This paper reports the experimental results of cesium sorption to the Wonju Granite, a typical Mesozoic granite in Korea, performed in an anaerobic chamber that mimics the anoxic environment of a deep disposal site. We measured the rates and amounts of cesium (¹³³Cs) removed by crushed granite samples in different electrolyte (NaCl, KCl, and CaCl₂) solutions and a synthetic groundwater solution, with variations in the initial cesium concentration (10^-5, 5×10^-6, 10^-6, 5×10^-7 M). The cesium sorption kinetic and isotherm data were successfully simulated by the pseudo-second-order kinetic model (r²= 0.99) and the Freundlich isotherm model (r²= 0.99), respectively. The sorption distribution coefficient of granite increased almost linearly with increasing biotite content in granite samples, indicating that biotite is an effective cesium scavenger. The cesium removal was minimal in KCl solution compared to that in NaCl or CaCl₂ solution, regardless of the ionic strength and initial cesium concentration that we examined, showing that K⁺ is the most competitive ion against cesium in sorption to granite. Because it is the main source mineral of K⁺ in fracture fluids, biotite may also hinder the sorption of cesium, which warrants further research.

• Korean Journal of Mineralogy and Petrology
• /
• v.35 no.2
• /
• pp.111-123
• /
• 2022

Carbonate green rust (CGR) and sulfate green rust (SGR) commonly occur in nature. In this study, CGR and SGR were synthesized through co-precipitation, and their formation mechanisms and physicochemical properties were investigated. X-ray diffraction (XRD) and Rietveld refinement showed both CGR and SGR with layered double hydroxide structure were successfully synthesized without any secondary phases under each synthetic condition. Refined structural parameters (unit cell) for two green rusts were a (=b) = 3.17 Å and c = 22.52 Å for CGR and a (=b) = 5.50 Å and c = 10.97 Å for SGR with the crystallite size 57.8 nm in diameter from (003) reflection and 40.1 nm from (001) reflections, respectively. Scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS) results showed that both CGR and SGR had typical hexagonal plate-like crystal morphologies but their chemical composition is different in the content of C and S. In addition, Fourier transform infrared (FT-IR) spectroscopy analysis revealed that carbonate (CO₃^2-) and sulfate (SO₄^2-) molecules were occupied as interlayer anions of CGR and SGR, respectively. These SEM/EDS and FT-IR results were in good agreement with XRD results. Changes in the solution chemistry (i.e., pH, Eh and residual iron concentrations (Fe(II):Fe(III)) of the mixed solution) were observed as a function of the injection time of hydroxyl ion (OH^-) into the iron solution. Three different stages were observed in the formation of both CGR and SGR; precursor, intermediator, and green rust in the formation of both CGR and SGR. This study provides co-precipitation methods for CGR and SGR in a way of the stable synthesis. In addition, our findings for the formation mechanisms of the two green rusts and their physicochemical properties will provide crucial information with researches and industrials in utilizing green rust.